default scanvideo to support 125mhz system clock for 640x480 - also means better compatibility as 25Mhz is better than 24Mhz when compared to 25.175Mhz

README.md

@@ -67,5 +67,4 @@ Name|Description
 ## Networking
 Name|Description
 ---|---
-[usb_host_webserver](net/usb_host_webserver)| A simple web server implemented as  
-
+[usb_host_webserver](net/usb_host_webserver)| A simple web server

apps/popcorn/CMakeLists.txt

@@ -24,6 +24,8 @@ if (PICO_ON_DEVICE)
                 VIDEO_DBI
 
                 PICO_SCANVIDEO_LINKED_SCANLINE_BUFFERS=1 # we do two rows at a time
+
+                #PICO_SCANVIDEO_48MHZ # still uses this for now
                 )
 
         target_link_libraries(popcorn

apps/popcorn/popcorn.c

@@ -1617,7 +1617,11 @@ void setup_audio() {
 }
 
 int main(void) {
+#if PICO_SCANVIDEO_48MHZ
     set_sys_clock_48mhz();
+#else
+    set_sys_clock_khz(50000, true);
+#endif
 
 #if USE_RGB_LOW_FOR_DEBUG_PINS
     gpio_dir_out_mask(0x421);

scanvideo/demo1/CMakeLists.txt

@@ -7,6 +7,7 @@ if (TARGET pico_scanvideo_dpi)
 
     target_compile_definitions(demo1
             PRIVATE
+            #PICO_SCANVIDEO_48MHZ
             # video overlay is distracting
 #            PICO_SCANVIDEO_PLANE_COUNT=3
             )

scanvideo/demo1/demo1.c

@@ -43,17 +43,6 @@ bool render_scanline_test_pattern(struct scanvideo_scanline_buffer *dest, int co
 bool render_scanline_pi(struct scanvideo_scanline_buffer *dest, int core);
 
 extern const struct scanvideo_pio_program video_24mhz_composable;
-const struct scanvideo_mode vga_mode_320x256_60 =
-        {
-                .default_timing = &vga_timing_640x480_60_default,
-                .pio_program = &video_24mhz_composable,
-                .width = 320,
-                .height = 256,
-                .xscale = 2,
-                .yscale = 480,
-                .yscale_denominator = 256
-        };
-
 
 //#define vga_mode vga_mode_1080p
 //#define vga_mode vga_mode_720p
@@ -612,7 +601,9 @@ int main(void) {
 
     gpio_put(27, 0);
 #if PICO_ON_DEVICE && !PICO_ON_FPGA
+#if PICO_SCANVIDEO_48MHz
     set_sys_clock_khz(96000, true);
+#endif
 //    set_sys_clock_48();
 #endif
 

scanvideo/flash_stream/flash_stream.c

@@ -133,7 +133,7 @@ void __time_critical_func(render_scanline)(struct scanvideo_scanline_buffer *des
 }
 
 int main(void) {
-    set_sys_clock_khz(192000, true);
+    set_sys_clock_khz(200000, true);
     setup_default_uart();
 
 #ifdef PICO_SMPS_MODE_PIN

scanvideo/flash_stream/img/pack.sh

@@ -6,4 +6,4 @@ rm -f *.bin pack.uf2
 ./packtiles -sdf bgar5515 Stone_Mountain_by_Brad_Huchteman.png stone_mountain.bin
 ./packtiles -sdf bgar5515 Voss_by_fortuneblues.png voss.bin
 cat *.bin > pack.bin
-uf2conv -f pico -b 0x1003c000 pack.bin -o pack.uf2
+uf2conv -f pico -b 0x1003c000 pack.bin -o pack.uf2

scanvideo/hscroll_dma_tiles/hscroll_dma_tiles.c

@@ -572,7 +572,9 @@ void go_core1(void (*execute)()) {
 }
 
 int main(void) {
+#if PICO_SCANVIDEO_48MHz
     set_sys_clock_48mhz();
+#endif
     setup_default_uart();
 
 #if PICO_NO_HARDWARE

scanvideo/mandelbrot/mandelbrot.c

@@ -239,19 +239,24 @@ void __time_critical_func(frame_update_logic)() {
 }
 
 int main(void) {
+    uint base_freq;
+#if PICO_SCANVIDEO_48MHZ
+    base_freq = 48000;
+#else
+    base_freq = 50000;
+#endif
 #if PICO_ON_DEVICE
 #ifdef TURBO_BOOST
     hw_set_bits(&mm_vreg_and_chip_reset->vreg, VREG_AND_CHIP_RESET_VREG_VSEL_BITS);
     sleep_ms(10);
-    set_sys_clock_khz(48000*6, true);
+    set_sys_clock_khz(base_freq*6, true);
 #else
-    //set_sys_clock(1536*MHZ, 4, 2);
-    set_sys_clock_khz(48000 * 4, true);
+    set_sys_clock_khz(base_freq * 3, true);
 #endif
 #endif
     // Re init uart now that clk_peri has changed
     setup_default_uart();
-    gpio_debug_pins_init();
+//    gpio_debug_pins_init();
 
     return vga_main();
 }

scanvideo/mario_tiles/mario_tiles.c

@@ -665,7 +665,9 @@ void go_core1(void (*execute)()) {
 }
 
 int main(void) {
+#if PICO_SCANVIDEO_48MHz
     set_sys_clock_48mhz();
+#endif
     setup_default_uart();
 
 #if PICO_NO_HARDWARE

scanvideo/scanvideo_minimal/scanvideo_minimal.c

@@ -104,7 +104,9 @@ void render_scanline(struct scanvideo_scanline_buffer *dest, int core) {
 
 
 int main(void) {
+#if PICO_SCANVIDEO_48MHz
     set_sys_clock_48mhz();
+#endif
     // Re init uart now that clk_peri has changed
     setup_default_uart();
 

scanvideo/sprite_demo/sprite_demo.c

@@ -176,6 +176,10 @@ int main(void) {
     sleep_ms(10);
     set_sys_clock(1536*MHZ, 4, 1);
 #else
+#if PICO_SCANVIDEO_48MHz
+    set_sys_clock_48mhz();
+#endif
+
     set_sys_clock_pll(1536 * MHZ, 4, 2);
 #endif
     // Re init uart now that clk_peri has changed

scanvideo/test_pattern/test_pattern.c

@@ -27,7 +27,6 @@ static semaphore_t video_initted;
 static bool invert;
 
 int main(void) {
-    set_sys_clock_48mhz();
     stdio_init_all();
 
     // create a semaphore to be posted when video init is complete

scanvideo/textmode/textmode.c

@@ -14,6 +14,9 @@
 #include "pico/sync.h"
 #include "font.h"
 
+// set this to 3, 4 or 5 for smallest to biggest font
+#define FRAGMENT_WORDS 4
+
 #if PICO_ON_DEVICE
 
 #include "hardware/structs/bus_ctrl.h"
@@ -168,8 +171,6 @@ uint32_t *font_raw_pixels;
 #else
 uint32_t font_raw_pixels[16384];
 #endif
-#define FRAGMENT_WORDS 4
-//#define FRAGMENT_WORDS 5
 #define FONT_WIDTH_WORDS FRAGMENT_WORDS
 #if FRAGMENT_WORDS == 5
 const lv_font_t *font = &ubuntu_mono10;
@@ -406,8 +407,8 @@ bool render_scanline_bg(struct scanvideo_scanline_buffer *dest, int core) {
     // todo for SOME REASON, 80 is the max we can do without starting to really get bus delays (even with priority)... not sure how this could be
     // todo actually it seems it can work, it just mostly starts incorrectly synced!?
 #define COUNT MIN(vga_mode.width/(FRAGMENT_WORDS*2)-1, 80)//MAX_SCANLINE_BUFFER_WORDS / 2 - 2)
-#undef COUNT
-#define COUNT 79
+//#undef COUNT
+//#define COUNT 79
     // we need to take up 5 words, since we have fixed width
 #if PICO_SCANVIDEO_PLANE1_FIXED_FRAGMENT_DMA
     dest->fragment_words = FRAGMENT_WORDS;
@@ -507,7 +508,9 @@ void go_core1(void (*execute)()) {
 }
 
 int main(void) {
+#if PICO_SCANVIDEO_48MHZ
     set_sys_clock_48mhz();
+#endif
     gpio_put(27, 0);
 
     setup_default_uart();