kopia lustrzana https://github.com/micropython/micropython
44 wiersze
1.7 KiB
C
44 wiersze
1.7 KiB
C
#define HYDRABUSV10
|
|
|
|
#define MICROPY_HW_BOARD_NAME "HydraBus1.0"
|
|
#define MICROPY_HW_MCU_NAME "STM32F4"
|
|
|
|
#define MICROPY_HW_HAS_SWITCH (1)
|
|
#define MICROPY_HW_HAS_SDCARD (1)
|
|
#define MICROPY_HW_HAS_MMA7660 (0)
|
|
#define MICROPY_HW_HAS_LIS3DSH (0)
|
|
#define MICROPY_HW_HAS_LCD (0)
|
|
#define MICROPY_HW_ENABLE_RNG (1)
|
|
#define MICROPY_HW_ENABLE_RTC (0)
|
|
#define MICROPY_HW_ENABLE_TIMER (1)
|
|
#define MICROPY_HW_ENABLE_SERVO (0)
|
|
#define MICROPY_HW_ENABLE_DAC (1)
|
|
#define MICROPY_HW_ENABLE_I2C1 (1)
|
|
#define MICROPY_HW_ENABLE_SPI1 (1)
|
|
#define MICROPY_HW_ENABLE_SPI2 (1)
|
|
#define MICROPY_HW_ENABLE_SPI3 (1)
|
|
#define MICROPY_HW_ENABLE_CAN (0)
|
|
|
|
// USRSW/UBTN (Needs Jumper UBTN) is pulled low. Pressing the button makes the input go high.
|
|
#define MICROPY_HW_USRSW_PIN (pin_A0)
|
|
#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL)
|
|
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING)
|
|
#define MICROPY_HW_USRSW_PRESSED (1)
|
|
|
|
// The HydraBus has 1 LED (Needs jumper on ULED)
|
|
#define MICROPY_HW_LED1 (pin_A4) // green
|
|
#define MICROPY_HW_LED2 (pin_A4) // same as LED1
|
|
#define MICROPY_HW_LED3 (pin_A4) // same as LED1
|
|
#define MICROPY_HW_LED4 (pin_A4) // same as LED1
|
|
#define MICROPY_HW_LED_OTYPE (GPIO_MODE_OUTPUT_PP)
|
|
#define MICROPY_HW_LED_ON(pin) (pin->gpio->BSRRL = pin->pin_mask)
|
|
#define MICROPY_HW_LED_OFF(pin) (pin->gpio->BSRRH = pin->pin_mask)
|
|
|
|
// SD card detect switch (not used, always on)
|
|
#define MICROPY_HW_SDCARD_DETECT_PIN (pin_A8)
|
|
#define MICROPY_HW_SDCARD_DETECT_PULL (GPIO_PULLUP)
|
|
#define MICROPY_HW_SDCARD_DETECT_PRESENT (1)
|
|
|
|
// USB config
|
|
#define MICROPY_HW_USB_OTG_ID_PIN (pin_A10)
|