kopia lustrzana https://github.com/micropython/micropython
97 wiersze
3.5 KiB
ReStructuredText
97 wiersze
3.5 KiB
ReStructuredText
.. currentmodule:: machine
|
|
|
|
class SPI -- a Serial Peripheral Interface bus protocol (master side)
|
|
=====================================================================
|
|
|
|
SPI is a synchronous serial protocol that is driven by a master. At the
|
|
physical level, a bus consists of 3 lines: SCK, MOSI, MISO. Multiple devices
|
|
can share the same bus. Each device should have a separate, 4th signal,
|
|
SS (Slave Select), to select a particular device on a bus with which
|
|
communication takes place. Management of an SS signal should happen in
|
|
user code (via machine.Pin class).
|
|
|
|
Constructors
|
|
------------
|
|
|
|
.. class:: SPI(id, ...)
|
|
|
|
Construct an SPI object on the given bus, ``id``. Values of ``id`` depend
|
|
on a particular port and its hardware. Values 0, 1, etc. are commonly used
|
|
to select hardware SPI block #0, #1, etc. Value -1 can be used for
|
|
bitbanging (software) implementation of SPI (if supported by a port).
|
|
|
|
With no additional parameters, the SPI object is created but not
|
|
initialised (it has the settings from the last initialisation of
|
|
the bus, if any). If extra arguments are given, the bus is initialised.
|
|
See ``init`` for parameters of initialisation.
|
|
|
|
Methods
|
|
-------
|
|
|
|
.. method:: SPI.init(baudrate=1000000, \*, polarity=0, phase=0, bits=8, firstbit=SPI.MSB, sck=None, mosi=None, miso=None, pins=(SCK, MOSI, MISO))
|
|
|
|
Initialise the SPI bus with the given parameters:
|
|
|
|
- ``baudrate`` is the SCK clock rate.
|
|
- ``polarity`` can be 0 or 1, and is the level the idle clock line sits at.
|
|
- ``phase`` can be 0 or 1 to sample data on the first or second clock edge
|
|
respectively.
|
|
- ``bits`` is the width in bits of each transfer. Only 8 is guaranteed to be supported by all hardware.
|
|
- ``firstbit`` can be ``SPI.MSB`` or ``SPI.LSB``.
|
|
- ``sck``, ``mosi``, ``miso`` are pins (machine.Pin) objects to use for bus signals. For most
|
|
hardware SPI blocks (as selected by ``id`` parameter to the constructor), pins are fixed
|
|
and cannot be changed. In some cases, hardware blocks allow 2-3 alternative pin sets for
|
|
a hardware SPI block. Arbitrary pin assignments are possible only for a bitbanging SPI driver
|
|
(``id`` = -1).
|
|
- ``pins`` - WiPy port doesn't ``sck``, ``mosi``, ``miso`` arguments, and instead allows to
|
|
specify them as a tuple of ``pins`` parameter.
|
|
|
|
.. method:: SPI.deinit()
|
|
|
|
Turn off the SPI bus.
|
|
|
|
.. method:: SPI.read(nbytes, write=0x00)
|
|
|
|
Read a number of bytes specified by ``nbytes`` while continuously writing
|
|
the single byte given by ``write``.
|
|
Returns a ``bytes`` object with the data that was read.
|
|
|
|
.. method:: SPI.readinto(buf, write=0x00)
|
|
|
|
Read into the buffer specified by ``buf`` while continuously writing the
|
|
single byte given by ``write``.
|
|
Returns ``None``.
|
|
|
|
Note: on WiPy this function returns the number of bytes read.
|
|
|
|
.. method:: SPI.write(buf)
|
|
|
|
Write the bytes contained in ``buf``.
|
|
Returns ``None``.
|
|
|
|
Note: on WiPy this function returns the number of bytes written.
|
|
|
|
.. method:: SPI.write_readinto(write_buf, read_buf)
|
|
|
|
Write the bytes from ``write_buf`` while reading into ``read_buf``. The
|
|
buffers can be the same or different, but both buffers must have the
|
|
same length.
|
|
Returns ``None``.
|
|
|
|
Note: on WiPy this function returns the number of bytes written.
|
|
|
|
Constants
|
|
---------
|
|
|
|
.. data:: SPI.MASTER
|
|
|
|
for initialising the SPI bus to master; this is only used for the WiPy
|
|
|
|
.. data:: SPI.MSB
|
|
|
|
set the first bit to be the most significant bit
|
|
|
|
.. data:: SPI.LSB
|
|
|
|
set the first bit to be the least significant bit
|