kopia lustrzana https://github.com/micropython/micropython
95 wiersze
4.2 KiB
ReStructuredText
95 wiersze
4.2 KiB
ReStructuredText
.. _mimxrt_general:
|
|
|
|
General information about the MIMXRT port
|
|
=========================================
|
|
|
|
The i.MXRT MCU family is a high performance family of devices made by NXP.
|
|
Based on an ARM7 core, they provide many on-chip I/O units for building
|
|
small to medium sized devices.
|
|
|
|
Multitude of boards
|
|
-------------------
|
|
|
|
There is a multitude of modules and boards from different sources which carry
|
|
an i.MXRT chip. MicroPython aims to provide a generic port which runs on
|
|
as many boards/modules as possible, but there may be limitations. The
|
|
NXP IMXRT1020-EVK and the Teensy 4.0 and Teensy 4.1 development boards are taken
|
|
as reference for the port (for example, testing is performed on them).
|
|
For any board you are using please make sure you have a data sheet, schematics
|
|
and other reference materials so you can look up any board-specific functions.
|
|
|
|
The following boards are supported by the port:
|
|
|
|
- MIMXRT1010-EVK
|
|
- MIMXRT1020-EVK
|
|
- MIMXRT1050-EVK
|
|
- MIMXRT1060-EVK
|
|
- MIMXRT1064-EVK
|
|
- Teensy 4.0
|
|
- Teensy 4.1
|
|
|
|
Supported MCUs
|
|
--------------
|
|
|
|
+-------------+--------------------+-------------------------+
|
|
| Product | CPU | Memory |
|
|
+=============+====================+=========================+
|
|
| i.MX RT1064 | Cortex-M7 @600 MHz | 1 MB SRAM, 4 MB Flash |
|
|
+-------------+--------------------+-------------------------+
|
|
| i.MX RT1061 | Cortex-M7 @600 MHz | 1 MB SRAM |
|
|
+-------------+--------------------+-------------------------+
|
|
| i.MX RT1062 | Cortex-M7 @600 MHz | 1 MB SRAM |
|
|
+-------------+--------------------+-------------------------+
|
|
| i.MX RT1050 | Cortex-M7 @600 MHz | 512 kB SRAM |
|
|
+-------------+--------------------+-------------------------+
|
|
| i.MX RT1020 | Cortex-M7 @500 MHz | 256 kB SRAM |
|
|
+-------------+--------------------+-------------------------+
|
|
| i.MX RT1015 | Cortex-M7 @500 MHz | 128 kB SRAM |
|
|
+-------------+--------------------+-------------------------+
|
|
| i.MX RT1010 | Cortex-M7 @500 MHz | 128 kB SRAM |
|
|
+-------------+--------------------+-------------------------+
|
|
|
|
Note: Most of the controllers do not have internal flash memory. Therefore
|
|
their flash capacity is dependent on an external flash chip.
|
|
|
|
To make a generic MIMXRT port and support as many boards as possible the
|
|
following design and implementation decision were made:
|
|
|
|
* GPIO pin numbering is based on the board numbering as well as on the
|
|
MCU numbering. Please have the manual/pin diagram of your board at hand
|
|
to find correspondence between your board pins and actual i.MXRT pins.
|
|
* All MCU pins are supported by MicroPython but not all are usable on any given board.
|
|
|
|
Technical specifications and SoC datasheets
|
|
-------------------------------------------
|
|
|
|
The data sheets and other reference material for i.MXRT chip are available
|
|
from the vendor site: https://www.nxp.com/products/processors-and-microcontrollers/arm-microcontrollers/i-mx-rt-crossover-mcus:IMX-RT-SERIES .
|
|
They are the primary reference for the chip technical specifications, capabilities,
|
|
operating modes, internal functioning, etc.
|
|
|
|
For your convenience, a few technical specifications are provided below:
|
|
|
|
* Architecture: ARM Cortex M7
|
|
* CPU frequency: up to 600MHz
|
|
* Total RAM available: up to 1 MByte (see table)
|
|
* BootROM: 96KB
|
|
* External FlashROM: code and data, via SPI Flash; usual size 2 - 16 MB
|
|
Some boards provide additional external RAM and SPI flash.
|
|
* GPIO: up to 124 (GPIOs are multiplexed with other functions, including
|
|
external FlashROM, UART, etc.)
|
|
* UART: 4 or 8 RX/TX UART. Hardware handshaking is supported by the MCU,
|
|
but the boards used for testing do not expose the signals.
|
|
* SPI: 2 or 4 low power SPI interfaces (software implementation available on every pin)
|
|
* I2C: 2 or 4 low power I2C interfaces (software implementation available on every pin)
|
|
* I2S: 1 to 3 I2S interfaces
|
|
* ADC: one or two 12-bit SAR ADC converters
|
|
* Ethernet controller (except i.MX RT1010/-1015)
|
|
* Programming: using BootROM bootloader from USB - due to external FlashROM
|
|
and always-available BootROM bootloader, the MIMXRT is not brickable
|
|
|
|
The lower numbers for UART, SPI and I2C apply to the i.MXRT 101x MCU.
|
|
|
|
For more information see the i.MXRT data sheets or reference manuals.
|
|
NXP provides software support through it's SDK packages.
|