//***************************************************************************** // // Copyright (C) 2014 Texas Instruments Incorporated - http://www.ti.com/ // // // Redistribution and use in source and binary forms, with or without // modification, are permitted provided that the following conditions // are met: // // Redistributions of source code must retain the above copyright // notice, this list of conditions and the following disclaimer. // // Redistributions in binary form must reproduce the above copyright // notice, this list of conditions and the following disclaimer in the // documentation and/or other materials provided with the // distribution. // // Neither the name of Texas Instruments Incorporated nor the names of // its contributors may be used to endorse or promote products derived // from this software without specific prior written permission. // // THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS // "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT // LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR // A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT // OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, // SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT // LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, // DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY // THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT // (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE // OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. // //***************************************************************************** #ifndef __HW_APPS_CONFIG_H__ #define __HW_APPS_CONFIG_H__ //***************************************************************************** // // The following are defines for the APPS_CONFIG register offsets. // //***************************************************************************** #define APPS_CONFIG_O_PATCH_TRAP_ADDR_REG \ 0x00000000 // Patch trap address Register // array #define APPS_CONFIG_O_PATCH_TRAP_EN_REG \ 0x00000078 #define APPS_CONFIG_O_FAULT_STATUS_REG \ 0x0000007C #define APPS_CONFIG_O_MEMSS_WR_ERR_CLR_REG \ 0x00000080 #define APPS_CONFIG_O_MEMSS_WR_ERR_ADDR_REG \ 0x00000084 #define APPS_CONFIG_O_DMA_DONE_INT_MASK \ 0x0000008C #define APPS_CONFIG_O_DMA_DONE_INT_MASK_SET \ 0x00000090 #define APPS_CONFIG_O_DMA_DONE_INT_MASK_CLR \ 0x00000094 #define APPS_CONFIG_O_DMA_DONE_INT_STS_CLR \ 0x00000098 #define APPS_CONFIG_O_DMA_DONE_INT_ACK \ 0x0000009C #define APPS_CONFIG_O_DMA_DONE_INT_STS_MASKED \ 0x000000A0 #define APPS_CONFIG_O_DMA_DONE_INT_STS_RAW \ 0x000000A4 #define APPS_CONFIG_O_FAULT_STATUS_CLR_REG \ 0x000000A8 #define APPS_CONFIG_O_RESERVD_REG_0 \ 0x000000AC #define APPS_CONFIG_O_GPT_TRIG_SEL \ 0x000000B0 #define APPS_CONFIG_O_TOP_DIE_SPARE_DIN_REG \ 0x000000B4 #define APPS_CONFIG_O_TOP_DIE_SPARE_DOUT_REG \ 0x000000B8 //****************************************************************************** // // The following are defines for the bit fields in the // APPS_CONFIG_O_PATCH_TRAP_ADDR_REG register. // //****************************************************************************** #define APPS_CONFIG_PATCH_TRAP_ADDR_REG_PATCH_TRAP_ADDR_M \ 0xFFFFFFFF // When PATCH_TRAP_EN[n] is set bus // fault is generated for the // address // PATCH_TRAP_ADDR_REG[n][31:0] from // Idcode bus. The exception routine // should take care to jump to the // location where the patch // correspond to this address is // kept. #define APPS_CONFIG_PATCH_TRAP_ADDR_REG_PATCH_TRAP_ADDR_S 0 //****************************************************************************** // // The following are defines for the bit fields in the // APPS_CONFIG_O_PATCH_TRAP_EN_REG register. // //****************************************************************************** #define APPS_CONFIG_PATCH_TRAP_EN_REG_PATCH_TRAP_EN_M \ 0x3FFFFFFF // When PATCH_TRAP_EN[n] is set bus // fault is generated for the // address PATCH_TRAP_ADD[n][31:0] // from Idcode bus. The exception // routine should take care to jump // to the location where the patch // correspond to this address is // kept. #define APPS_CONFIG_PATCH_TRAP_EN_REG_PATCH_TRAP_EN_S 0 //****************************************************************************** // // The following are defines for the bit fields in the // APPS_CONFIG_O_FAULT_STATUS_REG register. // //****************************************************************************** #define APPS_CONFIG_FAULT_STATUS_REG_PATCH_ERR_INDEX_M \ 0x0000003E // This field shows because of // which patch trap address the // bus_fault is generated. If the // PATCH_ERR bit is set, then it // means the bus fault is generated // because of // PATCH_TRAP_ADDR_REG[2^PATCH_ERR_INDEX] #define APPS_CONFIG_FAULT_STATUS_REG_PATCH_ERR_INDEX_S 1 #define APPS_CONFIG_FAULT_STATUS_REG_PATCH_ERR \ 0x00000001 // This bit is set when there is a // bus fault because of patched // address access to the Apps boot // rom. Write 0 to clear this // register. //****************************************************************************** // // The following are defines for the bit fields in the // APPS_CONFIG_O_MEMSS_WR_ERR_CLR_REG register. // //****************************************************************************** #define APPS_CONFIG_MEMSS_WR_ERR_CLR_REG_MEMSS_WR_ERR_CLR \ 0x00000001 // This bit is set when there is a // an error in memss write access. // And the address causing this // error is captured in // MEMSS_ERR_ADDR_REG. To capture // the next error address one have // to clear this bit. //****************************************************************************** // // The following are defines for the bit fields in the // APPS_CONFIG_O_MEMSS_WR_ERR_ADDR_REG register. // //****************************************************************************** //****************************************************************************** // // The following are defines for the bit fields in the // APPS_CONFIG_O_DMA_DONE_INT_MASK register. // //****************************************************************************** #define APPS_CONFIG_DMA_DONE_INT_MASK_ADC_WR_DMA_DONE_INT_MASK_M \ 0x0000F000 // 1= disable corresponding // interrupt;0 = interrupt enabled // bit 14: ADC channel 7 interrupt // enable/disable bit 13: ADC // channel 5 interrupt // enable/disable bit 12: ADC // channel 3 interrupt // enable/disable bit 11: ADC // channel 1 interrupt // enable/disable #define APPS_CONFIG_DMA_DONE_INT_MASK_ADC_WR_DMA_DONE_INT_MASK_S 12 #define APPS_CONFIG_DMA_DONE_INT_MASK_MCASP_WR_DMA_DONE_INT_MASK \ 0x00000800 // 1= disable corresponding // interrupt;0 = interrupt enabled #define APPS_CONFIG_DMA_DONE_INT_MASK_MCASP_RD_DMA_DONE_INT_MASK \ 0x00000400 // 1= disable corresponding // interrupt;0 = interrupt enabled #define APPS_CONFIG_DMA_DONE_INT_MASK_CAM_FIFO_EMPTY_DMA_DONE_INT_MASK \ 0x00000200 // 1= disable corresponding // interrupt;0 = interrupt enabled #define APPS_CONFIG_DMA_DONE_INT_MASK_CAM_THRESHHOLD_DMA_DONE_INT_MASK \ 0x00000100 // 1= disable corresponding // interrupt;0 = interrupt enabled #define APPS_CONFIG_DMA_DONE_INT_MASK_SHSPI_WR_DMA_DONE_INT_MASK \ 0x00000080 // 1= disable corresponding // interrupt;0 = interrupt enabled #define APPS_CONFIG_DMA_DONE_INT_MASK_SHSPI_RD_DMA_DONE_INT_MASK \ 0x00000040 // 1= disable corresponding // interrupt;0 = interrupt enabled #define APPS_CONFIG_DMA_DONE_INT_MASK_HOSTSPI_WR_DMA_DONE_INT_MASK \ 0x00000020 // 1= disable corresponding // interrupt;0 = interrupt enabled #define APPS_CONFIG_DMA_DONE_INT_MASK_HOSTSPI_RD_DMA_DONE_INT_MASK \ 0x00000010 // 1= disable corresponding // interrupt;0 = interrupt enabled #define APPS_CONFIG_DMA_DONE_INT_MASK_APPS_SPI_WR_DMA_DONE_INT_MASK \ 0x00000008 // 1= disable corresponding // interrupt;0 = interrupt enabled #define APPS_CONFIG_DMA_DONE_INT_MASK_APPS_SPI_RD_DMA_DONE_INT_MASK \ 0x00000004 // 1= disable corresponding // interrupt;0 = interrupt enabled #define APPS_CONFIG_DMA_DONE_INT_MASK_SDIOM_WR_DMA_DONE_INT_MASK \ 0x00000002 // 1= disable corresponding // interrupt;0 = interrupt enabled #define APPS_CONFIG_DMA_DONE_INT_MASK_SDIOM_RD_DMA_DONE_INT_MASK \ 0x00000001 // 1= disable corresponding // interrupt;0 = interrupt enabled //****************************************************************************** // // The following are defines for the bit fields in the // APPS_CONFIG_O_DMA_DONE_INT_MASK_SET register. // //****************************************************************************** #define APPS_CONFIG_DMA_DONE_INT_MASK_SET_ADC_WR_DMA_DONE_INT_MASK_SET_M \ 0x0000F000 // write 1 to set mask of the // corresponding DMA DONE IRQ;0 = no // effect bit 14: ADC channel 7 DMA // Done IRQ bit 13: ADC channel 5 // DMA Done IRQ bit 12: ADC channel // 3 DMA Done IRQ bit 11: ADC // channel 1 DMA Done IRQ #define APPS_CONFIG_DMA_DONE_INT_MASK_SET_ADC_WR_DMA_DONE_INT_MASK_SET_S 12 #define APPS_CONFIG_DMA_DONE_INT_MASK_SET_MCASP_WR_DMA_DONE_INT_MASK_SET \ 0x00000800 // write 1 to set mask of the // corresponding DMA DONE IRQ;0 = no // effect #define APPS_CONFIG_DMA_DONE_INT_MASK_SET_MCASP_RD_DMA_DONE_INT_MASK_SET \ 0x00000400 // write 1 to set mask of the // corresponding DMA DONE IRQ;0 = no // effect #define APPS_CONFIG_DMA_DONE_INT_MASK_SET_CAM_FIFO_EMPTY_DMA_DONE_INT_MASK_SET \ 0x00000200 // write 1 to set mask of the // corresponding DMA DONE IRQ;0 = no // effect #define APPS_CONFIG_DMA_DONE_INT_MASK_SET_CAM_THRESHHOLD_DMA_DONE_INT_MASK_SET \ 0x00000100 // write 1 to set mask of the // corresponding DMA DONE IRQ;0 = no // effect #define APPS_CONFIG_DMA_DONE_INT_MASK_SET_SHSPI_WR_DMA_DONE_INT_MASK_SET \ 0x00000080 // write 1 to set mask of the // corresponding DMA DONE IRQ;0 = no // effect #define APPS_CONFIG_DMA_DONE_INT_MASK_SET_SHSPI_RD_DMA_DONE_INT_MASK_SET \ 0x00000040 // write 1 to set mask of the // corresponding DMA DONE IRQ;0 = no // effect #define APPS_CONFIG_DMA_DONE_INT_MASK_SET_HOSTSPI_WR_DMA_DONE_INT_MASK_SET \ 0x00000020 // write 1 to set mask of the // corresponding DMA DONE IRQ;0 = no // effect #define APPS_CONFIG_DMA_DONE_INT_MASK_SET_HOSTSPI_RD_DMA_DONE_INT_MASK_SET \ 0x00000010 // write 1 to set mask of the // corresponding DMA DONE IRQ;0 = no // effect #define APPS_CONFIG_DMA_DONE_INT_MASK_SET_APPS_SPI_WR_DMA_DONE_INT_MASK_SET \ 0x00000008 // write 1 to set mask of the // corresponding DMA DONE IRQ;0 = no // effect #define APPS_CONFIG_DMA_DONE_INT_MASK_SET_APPS_SPI_RD_DMA_DONE_INT_MASK_SET \ 0x00000004 // write 1 to set mask of the // corresponding DMA DONE IRQ;0 = no // effect #define APPS_CONFIG_DMA_DONE_INT_MASK_SET_SDIOM_WR_DMA_DONE_INT_MASK_SET \ 0x00000002 // write 1 to set mask of the // corresponding DMA DONE IRQ;0 = no // effect #define APPS_CONFIG_DMA_DONE_INT_MASK_SET_SDIOM_RD_DMA_DONE_INT_MASK_SET \ 0x00000001 // write 1 to set mask of the // corresponding DMA DONE IRQ;0 = no // effect //****************************************************************************** // // The following are defines for the bit fields in the // APPS_CONFIG_O_DMA_DONE_INT_MASK_CLR register. // //****************************************************************************** #define APPS_CONFIG_DMA_DONE_INT_MASK_CLR_ADC_WR_DMA_DONE_INT_MASK_CLR_M \ 0x0000F000 // write 1 to clear mask of the // corresponding DMA DONE IRQ;0 = no // effect bit 14: ADC channel 7 DMA // Done IRQ mask bit 13: ADC channel // 5 DMA Done IRQ mask bit 12: ADC // channel 3 DMA Done IRQ mask bit // 11: ADC channel 1 DMA Done IRQ // mask #define APPS_CONFIG_DMA_DONE_INT_MASK_CLR_ADC_WR_DMA_DONE_INT_MASK_CLR_S 12 #define APPS_CONFIG_DMA_DONE_INT_MASK_CLR_MACASP_WR_DMA_DONE_INT_MASK_CLR \ 0x00000800 // write 1 to clear mask of the // corresponding DMA DONE IRQ;0 = no // effect #define APPS_CONFIG_DMA_DONE_INT_MASK_CLR_MCASP_RD_DMA_DONE_INT_MASK_CLR \ 0x00000400 // write 1 to clear mask of the // corresponding DMA DONE IRQ;0 = no // effect #define APPS_CONFIG_DMA_DONE_INT_MASK_CLR_CAM_FIFO_EMPTY_DMA_DONE_INT_MASK_CLR \ 0x00000200 // write 1 to clear mask of the // corresponding DMA DONE IRQ;0 = no // effect #define APPS_CONFIG_DMA_DONE_INT_MASK_CLR_CAM_THRESHHOLD_DMA_DONE_INT_MASK_CLR \ 0x00000100 // write 1 to clear mask of the // corresponding DMA DONE IRQ;0 = no // effect #define APPS_CONFIG_DMA_DONE_INT_MASK_CLR_SHSPI_WR_DMA_DONE_INT_MASK_CLR \ 0x00000080 // write 1 to clear mask of the // corresponding DMA DONE IRQ;0 = no // effect #define APPS_CONFIG_DMA_DONE_INT_MASK_CLR_SHSPI_RD_DMA_DONE_INT_MASK_CLR \ 0x00000040 // write 1 to clear mask of the // corresponding DMA DONE IRQ;0 = no // effect #define APPS_CONFIG_DMA_DONE_INT_MASK_CLR_HOSTSPI_WR_DMA_DONE_INT_MASK_CLR \ 0x00000020 // write 1 to clear mask of the // corresponding DMA DONE IRQ;0 = no // effect #define APPS_CONFIG_DMA_DONE_INT_MASK_CLR_HOSTSPI_RD_DMA_DONE_INT_MASK_CLR \ 0x00000010 // write 1 to clear mask of the // corresponding DMA DONE IRQ;0 = no // effect #define APPS_CONFIG_DMA_DONE_INT_MASK_CLR_APPS_SPI_WR_DMA_DONE_INT_MASK_CLR \ 0x00000008 // write 1 to clear mask of the // corresponding DMA DONE IRQ;0 = no // effect #define APPS_CONFIG_DMA_DONE_INT_MASK_CLR_APPS_SPI_RD_DMA_DONE_INT_MASK_CLR \ 0x00000004 // write 1 to clear mask of the // corresponding DMA DONE IRQ;0 = no // effect #define APPS_CONFIG_DMA_DONE_INT_MASK_CLR_SDIOM_WR_DMA_DONE_INT_MASK_CLR \ 0x00000002 // write 1 to clear mask of the // corresponding DMA DONE IRQ;0 = no // effect #define APPS_CONFIG_DMA_DONE_INT_MASK_CLR_SDIOM_RD_DMA_DONE_INT_MASK_CLR \ 0x00000001 // write 1 to clear mask of the // corresponding DMA DONE IRQ;0 = no // effect //****************************************************************************** // // The following are defines for the bit fields in the // APPS_CONFIG_O_DMA_DONE_INT_STS_CLR register. // //****************************************************************************** #define APPS_CONFIG_DMA_DONE_INT_STS_CLR_DMA_INT_STS_CLR_M \ 0xFFFFFFFF // write 1 or 0 to clear all // DMA_DONE interrupt; #define APPS_CONFIG_DMA_DONE_INT_STS_CLR_DMA_INT_STS_CLR_S 0 //****************************************************************************** // // The following are defines for the bit fields in the // APPS_CONFIG_O_DMA_DONE_INT_ACK register. // //****************************************************************************** #define APPS_CONFIG_DMA_DONE_INT_ACK_ADC_WR_DMA_DONE_INT_ACK_M \ 0x0000F000 // write 1 to clear corresponding // interrupt; 0 = no effect; bit 14: // ADC channel 7 DMA Done IRQ bit // 13: ADC channel 5 DMA Done IRQ // bit 12: ADC channel 3 DMA Done // IRQ bit 11: ADC channel 1 DMA // Done IRQ #define APPS_CONFIG_DMA_DONE_INT_ACK_ADC_WR_DMA_DONE_INT_ACK_S 12 #define APPS_CONFIG_DMA_DONE_INT_ACK_MCASP_WR_DMA_DONE_INT_ACK \ 0x00000800 // write 1 to clear corresponding // interrupt; 0 = no effect; #define APPS_CONFIG_DMA_DONE_INT_ACK_MCASP_RD_DMA_DONE_INT_ACK \ 0x00000400 // write 1 to clear corresponding // interrupt; 0 = no effect; #define APPS_CONFIG_DMA_DONE_INT_ACK_CAM_FIFO_EMPTY_DMA_DONE_INT_ACK \ 0x00000200 // write 1 to clear corresponding // interrupt; 0 = no effect; #define APPS_CONFIG_DMA_DONE_INT_ACK_CAM_THRESHHOLD_DMA_DONE_INT_ACK \ 0x00000100 // write 1 to clear corresponding // interrupt; 0 = no effect; #define APPS_CONFIG_DMA_DONE_INT_ACK_SHSPI_WR_DMA_DONE_INT_ACK \ 0x00000080 // write 1 to clear corresponding // interrupt; 0 = no effect; #define APPS_CONFIG_DMA_DONE_INT_ACK_SHSPI_RD_DMA_DONE_INT_ACK \ 0x00000040 // write 1 to clear corresponding // interrupt; 0 = no effect; #define APPS_CONFIG_DMA_DONE_INT_ACK_HOSTSPI_WR_DMA_DONE_INT_ACK \ 0x00000020 // write 1 to clear corresponding // interrupt; 0 = no effect; #define APPS_CONFIG_DMA_DONE_INT_ACK_HOSTSPI_RD_DMA_DONE_INT_ACK \ 0x00000010 // write 1 to clear corresponding // interrupt; 0 = no effect; #define APPS_CONFIG_DMA_DONE_INT_ACK_APPS_SPI_WR_DMA_DONE_INT_ACK \ 0x00000008 // write 1 to clear corresponding // interrupt; 0 = no effect; #define APPS_CONFIG_DMA_DONE_INT_ACK_APPS_SPI_RD_DMA_DONE_INT_ACK \ 0x00000004 // write 1 to clear corresponding // interrupt; 0 = no effect; #define APPS_CONFIG_DMA_DONE_INT_ACK_SDIOM_WR_DMA_DONE_INT_ACK \ 0x00000002 // write 1 to clear corresponding // interrupt; 0 = no effect; #define APPS_CONFIG_DMA_DONE_INT_ACK_SDIOM_RD_DMA_DONE_INT_ACK \ 0x00000001 // write 1 to clear corresponding // interrupt; 0 = no effect; //****************************************************************************** // // The following are defines for the bit fields in the // APPS_CONFIG_O_DMA_DONE_INT_STS_MASKED register. // //****************************************************************************** #define APPS_CONFIG_DMA_DONE_INT_STS_MASKED_ADC_WR_DMA_DONE_INT_STS_MASKED_M \ 0x0000F000 // 1= corresponding interrupt is // active and not masked. read is // non-destructive;0 = corresponding // interrupt is inactive or masked // by DMA_DONE_INT mask bit 14: ADC // channel 7 DMA Done IRQ bit 13: // ADC channel 5 DMA Done IRQ bit // 12: ADC channel 3 DMA Done IRQ // bit 11: ADC channel 1 DMA Done // IRQ #define APPS_CONFIG_DMA_DONE_INT_STS_MASKED_ADC_WR_DMA_DONE_INT_STS_MASKED_S 12 #define APPS_CONFIG_DMA_DONE_INT_STS_MASKED_MCASP_WR_DMA_DONE_INT_STS_MASKED \ 0x00000800 // 1= corresponding interrupt is // active and not masked. read is // non-destructive;0 = corresponding // interrupt is inactive or masked // by DMA_DONE_INT mask #define APPS_CONFIG_DMA_DONE_INT_STS_MASKED_MCASP_RD_DMA_DONE_INT_STS_MASKED \ 0x00000400 // 1= corresponding interrupt is // active and not masked. read is // non-destructive;0 = corresponding // interrupt is inactive or masked // by DMA_DONE_INT mask #define APPS_CONFIG_DMA_DONE_INT_STS_MASKED_CAM_FIFO_EMPTY_DMA_DONE_INT_STS_MASKED \ 0x00000200 // 1= corresponding interrupt is // active and not masked. read is // non-destructive;0 = corresponding // interrupt is inactive or masked // by DMA_DONE_INT mask #define APPS_CONFIG_DMA_DONE_INT_STS_MASKED_CAM_THRESHHOLD_DMA_DONE_INT_STS_MASKED \ 0x00000100 // 1= corresponding interrupt is // active and not masked. read is // non-destructive;0 = corresponding // interrupt is inactive or masked // by DMA_DONE_INT mask #define APPS_CONFIG_DMA_DONE_INT_STS_MASKED_SHSPI_WR_DMA_DONE_INT_STS_MASKED \ 0x00000080 // 1= corresponding interrupt is // active and not masked. read is // non-destructive;0 = corresponding // interrupt is inactive or masked // by DMA_DONE_INT mask #define APPS_CONFIG_DMA_DONE_INT_STS_MASKED_SHSPI_RD_DMA_DONE_INT_STS_MASKED \ 0x00000040 // 1= corresponding interrupt is // active and not masked. read is // non-destructive;0 = corresponding // interrupt is inactive or masked // by DMA_DONE_INT mask #define APPS_CONFIG_DMA_DONE_INT_STS_MASKED_HOSTSPI_WR_DMA_DONE_INT_STS_MASKED \ 0x00000020 // 1= corresponding interrupt is // active and not masked. read is // non-destructive;0 = corresponding // interrupt is inactive or masked // by DMA_DONE_INT mask #define APPS_CONFIG_DMA_DONE_INT_STS_MASKED_HOSTSPI_RD_DMA_DONE_INT_STS_MASKED \ 0x00000010 // 1= corresponding interrupt is // active and not masked. read is // non-destructive;0 = corresponding // interrupt is inactive or masked // by DMA_DONE_INT mask #define APPS_CONFIG_DMA_DONE_INT_STS_MASKED_APPS_SPI_WR_DMA_DONE_INT_STS_MASKED \ 0x00000008 // 1= corresponding interrupt is // active and not masked. read is // non-destructive;0 = corresponding // interrupt is inactive or masked // by DMA_DONE_INT mask #define APPS_CONFIG_DMA_DONE_INT_STS_MASKED_APPS_SPI_RD_DMA_DONE_INT_STS_MASKED \ 0x00000004 // 1= corresponding interrupt is // active and not masked. read is // non-destructive;0 = corresponding // interrupt is inactive or masked // by DMA_DONE_INT mask #define APPS_CONFIG_DMA_DONE_INT_STS_MASKED_SDIOM_WR_DMA_DONE_INT_STS_MASKED \ 0x00000002 // 1= corresponding interrupt is // active and not masked. read is // non-destructive;0 = corresponding // interrupt is inactive or masked // by DMA_DONE_INT mask #define APPS_CONFIG_DMA_DONE_INT_STS_MASKED_SDIOM_RD_DMA_DONE_INT_STS_MASKED \ 0x00000001 // 1= corresponding interrupt is // active and not masked. read is // non-destructive;0 = corresponding // interrupt is inactive or masked // by DMA_DONE_INT mask //****************************************************************************** // // The following are defines for the bit fields in the // APPS_CONFIG_O_DMA_DONE_INT_STS_RAW register. // //****************************************************************************** #define APPS_CONFIG_DMA_DONE_INT_STS_RAW_ADC_WR_DMA_DONE_INT_STS_RAW_M \ 0x0000F000 // 1= corresponding interrupt is // active. read is non-destructive;0 // = corresponding interrupt is // inactive bit 14: ADC channel 7 // DMA Done IRQ bit 13: ADC channel // 5 DMA Done IRQ bit 12: ADC // channel 3 DMA Done IRQ bit 11: // ADC channel 1 DMA Done IRQ #define APPS_CONFIG_DMA_DONE_INT_STS_RAW_ADC_WR_DMA_DONE_INT_STS_RAW_S 12 #define APPS_CONFIG_DMA_DONE_INT_STS_RAW_MCASP_WR_DMA_DONE_INT_STS_RAW \ 0x00000800 // 1= corresponding interrupt is // active. read is non-destructive;0 // = corresponding interrupt is // inactive #define APPS_CONFIG_DMA_DONE_INT_STS_RAW_MCASP_RD_DMA_DONE_INT_STS_RAW \ 0x00000400 // 1= corresponding interrupt is // active. read is non-destructive;0 // = corresponding interrupt is // inactive #define APPS_CONFIG_DMA_DONE_INT_STS_RAW_CAM_EPMTY_FIFO_DMA_DONE_INT_STS_RAW \ 0x00000200 // 1= corresponding interrupt is // active. read is non-destructive;0 // = corresponding interrupt is // inactive #define APPS_CONFIG_DMA_DONE_INT_STS_RAW_CAM_THRESHHOLD_DMA_DONE_INT_STS_RAW \ 0x00000100 // 1= corresponding interrupt is // active. read is non-destructive;0 // = corresponding interrupt is // inactive #define APPS_CONFIG_DMA_DONE_INT_STS_RAW_SHSPI_WR_DMA_DONE_INT_STS_RAW \ 0x00000080 // 1= corresponding interrupt is // active. read is non-destructive;0 // = corresponding interrupt is // inactive #define APPS_CONFIG_DMA_DONE_INT_STS_RAW_SHSPI_RD_DMA_DONE_INT_STS_RAW \ 0x00000040 // 1= corresponding interrupt is // active. read is non-destructive;0 // = corresponding interrupt is // inactive #define APPS_CONFIG_DMA_DONE_INT_STS_RAW_HOSTSPI_WR_DMA_DONE_INT_STS_RAW \ 0x00000020 // 1= corresponding interrupt is // active. read is non-destructive;0 // = corresponding interrupt is // inactive #define APPS_CONFIG_DMA_DONE_INT_STS_RAW_HOSTSPI_RD_DMA_DONE_INT_STS_RAW \ 0x00000010 // 1= corresponding interrupt is // active. read is non-destructive;0 // = corresponding interrupt is // inactive #define APPS_CONFIG_DMA_DONE_INT_STS_RAW_APPS_SPI_WR_DMA_DONE_INT_STS_RAW \ 0x00000008 // 1= corresponding interrupt is // active. read is non-destructive;0 // = corresponding interrupt is // inactive #define APPS_CONFIG_DMA_DONE_INT_STS_RAW_APPS_SPI_RD_DMA_DONE_INT_STS_RAW \ 0x00000004 // 1= corresponding interrupt is // active. read is non-destructive;0 // = corresponding interrupt is // inactive #define APPS_CONFIG_DMA_DONE_INT_STS_RAW_SDIOM_WR_DMA_DONE_INT_STS_RAW \ 0x00000002 // 1= corresponding interrupt is // active. read is non-destructive;0 // = corresponding interrupt is // inactive #define APPS_CONFIG_DMA_DONE_INT_STS_RAW_SDIOM_RD_DMA_DONE_INT_STS_RAW \ 0x00000001 // 1= corresponding interrupt is // active. read is non-destructive;0 // = corresponding interrupt is // inactive //****************************************************************************** // // The following are defines for the bit fields in the // APPS_CONFIG_O_FAULT_STATUS_CLR_REG register. // //****************************************************************************** #define APPS_CONFIG_FAULT_STATUS_CLR_REG_PATCH_ERR_CLR \ 0x00000001 // Write 1 to clear the LSB of // FAULT_STATUS_REG //****************************************************************************** // // The following are defines for the bit fields in the // APPS_CONFIG_O_RESERVD_REG_0 register. // //****************************************************************************** //****************************************************************************** // // The following are defines for the bit fields in the // APPS_CONFIG_O_GPT_TRIG_SEL register. // //****************************************************************************** #define APPS_CONFIG_GPT_TRIG_SEL_GPT_TRIG_SEL_M \ 0x000000FF // This bit is implemented for GPT // trigger mode select. GPT IP // support 2 modes: RTC mode and // external trigger. When this bit // is set to logic '1': enable // external trigger mode for APPS // GPT CP0 and CP1 pin. bit 0: when // set '1' enable external GPT // trigger 0 on GPIO0 CP0 pin else // RTC mode is selected. bit 1: when // set '1' enable external GPT // trigger 1 on GPIO0 CP1 pin else // RTC mode is selected. bit 2: when // set '1' enable external GPT // trigger 2 on GPIO1 CP0 pin else // RTC mode is selected. bit 3: when // set '1' enable external GPT // trigger 3 on GPIO1 CP1 pin else // RTC mode is selected. bit 4: when // set '1' enable external GPT // trigger 4 on GPIO2 CP0 pin else // RTC mode is selected. bit 5: when // set '1' enable external GPT // trigger 5 on GPIO2 CP1 pin else // RTC mode is selected. bit 6: when // set '1' enable external GPT // trigger 6 on GPIO3 CP0 pin else // RTC mode is selected. bit 7: when // set '1' enable external GPT // trigger 7 on GPIO3 CP1 pin else // RTC mode is selected. #define APPS_CONFIG_GPT_TRIG_SEL_GPT_TRIG_SEL_S 0 //****************************************************************************** // // The following are defines for the bit fields in the // APPS_CONFIG_O_TOP_DIE_SPARE_DIN_REG register. // //****************************************************************************** #define APPS_CONFIG_TOP_DIE_SPARE_DIN_REG_D2D_SPARE_DIN_M \ 0x00000007 // Capture data from d2d_spare pads #define APPS_CONFIG_TOP_DIE_SPARE_DIN_REG_D2D_SPARE_DIN_S 0 //****************************************************************************** // // The following are defines for the bit fields in the // APPS_CONFIG_O_TOP_DIE_SPARE_DOUT_REG register. // //****************************************************************************** #define APPS_CONFIG_TOP_DIE_SPARE_DOUT_REG_D2D_SPARE_DOUT_M \ 0x00000007 // Send data to d2d_spare pads - // eventually this will get // registered in top die #define APPS_CONFIG_TOP_DIE_SPARE_DOUT_REG_D2D_SPARE_DOUT_S 0 #endif // __HW_APPS_CONFIG_H__