Wykres commitów

21 Commity (d46dc5e1738d843b83f1668798669ff177119d03)

Autor SHA1 Wiadomość Data
Damien George 82b4ab7576 stm32/boards: Move includes to after defines in all hal_conf.h files.
The include of HAL headers should come after the HAL configuration defines,
so that the headers can see whether the defines were made or not, to
provide defaults and configure various things.

Signed-off-by: Damien George <damien@micropython.org>
2023-09-28 17:30:38 +10:00
Jim Mussared f5f9edf645 all: Rename UMODULE to MODULE in preprocessor/Makefile vars.
This work was funded through GitHub Sponsors.

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2023-06-08 17:54:11 +10:00
Jim Mussared 6250337c9c ports: Make all network-capable boards use bundle-networking.
This will ensure that any board with networking support gets:
 - webrepl
 - mip
 - urequests
 - ntptime

This work was funded through GitHub Sponsors.

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2023-02-01 12:42:06 +11:00
Damien George df3f59ca4b ports: Update board.json files to link to new board images.
Signed-off-by: Damien George <damien@micropython.org>
2022-01-07 11:33:28 +11:00
Jim Mussared e359b077dd ports: Add board.json for all boards.
This will be used by https://micropython.org/download/ to generate the
full listing of boards and firmware files.

Optionally supports a board.md for additional customisation of the
download page, as well as deploy.md for flashing instructions.

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2021-10-27 14:04:53 +11:00
Mike Causer 47b778332a all: Replace busses with buses.
"buses" is the widely accepted plural form of "bus".
2021-05-20 23:22:03 +10:00
Damien George 009b1f6559 stm32/boards: Rework all stm32??xx_hal_conf.h files to use common code.
This eliminates a lot of duplicated code in these header files.
2019-06-25 14:18:24 +10:00
Damien George 5da60ff9cb stm32/boards: Enable ussl module via mbedtls for boards with network. 2019-06-24 17:48:28 +10:00
Damien George 9670b26526 stm32: Rename MICROPY_HW_HAS_SDCARD to MICROPY_HW_ENABLE_SDCARD.
For consistency with the majority of other MICROPY_HW_ENABLE_xxx macros.
2019-04-01 15:21:26 +11:00
Damien George e61862d063 stm32/boards: Update to use new build config for lwip component. 2019-03-04 23:34:03 +11:00
Damien George b3513f54d3 stm32/boards/STM32F7DISC: Enable lwIP and Ethernet peripheral. 2019-02-26 23:32:19 +11:00
Andrew Leech 338635ccc6 stm32/main: Add configuration macros for board to set heap start/end.
The macros are MICROPY_HEAP_START and MICROPY_HEAP_END, and if not defined
by a board then the default values will be used (maximum heap from SRAM as
defined by linker symbols).

As part of this commit the SDRAM initialisation is moved to much earlier in
main() to potentially make it available to other peripherals and avoid
re-initialisation on soft-reboot.  On boards with SDRAM enabled the heap
has been set to use that.
2018-10-05 17:30:18 +10:00
forester3 02fbb0a455 stm32/boards/STM32F7DISC: Enable onboard SDRAM.
The default SYSCLK frequency is reduced to 192MHz because SDRAM requires it
to be 200MHz or less.
2018-08-14 16:04:10 +10:00
Damien George a7ebac2eae stm32/can: Allow CAN pins to be configured per board.
This patch allows a given board to configure which pins are used for the
CAN peripherals, in a similar way to all the other bus peripherals (I2C,
UART, SPI).  To enable CAN on a board the mpconfigboard.h file should
define (for example):

    #define MICROPY_HW_CAN1_TX (pin_B9)
    #define MICROPY_HW_CAN1_RX (pin_B8)
    #define MICROPY_HW_CAN2_TX (pin_B13)
    #define MICROPY_HW_CAN2_RX (pin_B12)

And the board config file should no longer define MICROPY_HW_ENABLE_CAN.
2018-04-11 16:35:24 +10:00
Damien George ed75b2655f stm32/Makefile: Allow a board to config either 1 or 2 firmware sections.
This patch forces a board to explicitly define TEXT1_ADDR in order to
split the firmware into two separate pieces.  Otherwise the default is now
to produce only a single continuous firmware image with all ISR, text and
data together.
2018-03-27 21:24:15 +11:00
Damien George 7aec06ca9a stm32/boards: Allow boards to have finer control over the linker script.
This patch allows a particular board to independently specify the linker
scripts for 1) the MCU memory layout; 2) how the different firmware
sections are arranged in memory.  Right now all boards follow the same
layout with two separate firmware section, one for the ISR and one for the
text and data.  This leaves room for storage (filesystem data) to live
between the firmware sections.

The idea with this patch is to accommodate boards that don't have internal
flash storage and only need to have one continuous firmware section.  Thus
the common.ld script is renamed to common_ifs.ld to make explicit that it
is used for cases where the board has internal flash storage.
2018-03-27 21:17:48 +11:00
Damien George 34911f1a57 stm32/boards: Update all boards to work with new USB configuration. 2018-02-13 18:57:01 +11:00
Damien George 3eb0694b97 stm32: Update HAL macro and constant names to use newer versions.
Newer versions of the HAL use names which are cleaner and more
self-consistent amongst the HAL itself.  This patch switches to use those
names in most places so it is easier to update the HAL in the future.
2018-02-13 15:37:35 +11:00
Damien George 02f88cb2df stm32/boards: Remove all config options that are set to defaults.
mpconfigboard_common.h now sets the defaults so there is no longer a need
to explicitly list all configuration options in a board's mpconfigboard.h
file.
2018-02-09 18:40:40 +11:00
Damien George 6906255dcd stm32/boards: Remove obsolete and unused board-specific defines.
These board-level macros have been completely replaced by feature-level
config options.
2017-11-20 15:25:28 +11:00
Damien George 01dd7804b8 ports: Make new ports/ sub-directory and move all ports there.
This is to keep the top-level directory clean, to make it clear what is
core and what is a port, and to allow the repository to grow with new ports
in a sustainable way.
2017-09-06 13:40:51 +10:00