In that case, no Pin will be configured for the CS signal, even if it is
internally still generated. That setting allows to use any pin for CS,
which then must be controlled by the Python script.
Also make the default cs=-1 to match other ports (software CS).
The new teensy loader keeps the file system under certain conditions:
- The file size is properly set in the file header.
- The header version is 4.3
These changes are implemented here, requiring a backport of
fsl_flexspi_nor_boot.c. There is still a problem with the command line
version of the teensy loader, which fails on the first attempt. At the
second attempt it works. The GUI version of the teensy loader is fine.
Changes in this commit:
- Manifest include's now use the directory path where possible (no longer
necessary to include the manifest.py file explicitly).
- Add manifest.py for all drivers and components that are referenced by
port/board manifests.
- Replace all uses of freeze() with package()/module(), except for port and
board modules.
- Use opt=3 everywhere, for consistency and to reduce code size.
- Use require() instead of include() for all micropython-lib references.
- Remove support for optional board-level manifest.py in mimxrt port, to
make it behave the same as other ports (the board must set
FROZEN_MANIFEST to a custom manifest.py, which can optionally include the
default, port-level manifest).
- Also reinstates modules that were accidentally removed from the esp8266
512k build in fbe9417b90.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Signed-off-by: Damien George <damien@micropython.org>
uart.flush()
flush() will wait until all characters have been sent.To avoid a
permanent lock, a timeout applies depending on the size of txbuf
and the baud rate.
ret = uart.txdone()
ret is True if no transfer is in progress.
ret is False otherwise.
Previously the desired output type was specified. Now make the type part
of the function name. Because this function is used in a few places this
saves code size due to smaller call-site.
This makes `mp_obj_new_str_type_from_vstr` a private function of objstr.c
(which is almost the only place where the output type isn't a compile-time
constant).
This saves ~140 bytes on PYBV11.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Since commit e65d1e69e8 there is no longer an
io.FileIO class, so this option is no longer needed.
This option also controlled whether or not files supported being opened in
binary mode (eg 'rb'), and could, if disabled, lead to confusion as to why
opening a file in binary mode silently did the wrong thing (it would just
open in text mode if MICROPY_PY_IO_FILEIO was disabled).
The various VFS implementations (POSIX, FAT, LFS) were the only places
where enabling this option made a difference, and in almost all cases where
one of these filesystems were enabled, MICROPY_PY_IO_FILEIO was also
enabled. So it makes sense to just unconditionally enable this feature
(ability to open a file in binary mode) in all cases, and so just remove
this config option altogether. That makes configuration simpler and means
binary file support always exists (and opening a file in binary mode is
arguably more fundamental than opening in text mode, so if anything should
be configurable then it should be the ability to open in text mode).
Signed-off-by: Damien George <damien@micropython.org>
These were added in Python 3.5.
Enabled via MICROPY_PY_BUILTINS_BYTES_HEX, and enabled by default for all
ports that currently have ubinascii.
Rework ubinascii to use the implementation of these methods.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
For bare metal ARM & xtensa targets, passing -g will make the ELF file
larger but doesn't change the binary size. However, this means tools like
gdb, addr2line, etc can extract source-level information from the ELF.
Also standardise -ggdb to -g, these produce the exact same ELF file on
arm-none-eabi-gcc and will use DWARF format for all these ports.
Fixes:
- Should read `definitions` rather than `defintions`.
- Should read `resolution` rather than `resoultion`.
- Should read `inefficient` rather than `inefficent`.
- Should read `closed` rather than `closded`.
Signed-off-by: Tim Gates <tim.gates@iress.com>
rp2: change tud_task() to tud_task_ext().
mimxrt: use lib/tinyusb/src/portable/chipidea/ci_hs/dcd_ci_hs.c instead of
lib/tinyusb/src/portable/nxp/transdimension/dcd_transdimension.c.
nrf: add a definition for the changed tud_task(). tud_task() is changed
to tud_task_ext(), and the #define for backward compatibility is in
src/device/usbd.h.
The items I know which are fixed with this version:
- Fix for the SAMD USB lock-up.
- Support the MIMXRT11XX series of MCUs.
- Fix a wrong pin definition for MIMXRT1050_EVKB.
Tested with the MIMXRT boards, rp2 Pico, SAMD boards, nrf board.
All ports that use mbedtls use the custom error messages in
mp_mbedtls_errors.c. This commit simplifies the build so that ports don't
need to explicitly add this file, it's now used by default when mbedtls is
enabled.
Signed-off-by: Damien George <damien@micropython.org>
All in-tree uses of MICROPY_PORT_ROOT_POINTERS have been replaced with
MP_REGISTER_ROOT_POINTER(), so now we can remove both
MICROPY_PORT_ROOT_POINTERS and MICROPY_BOARD_ROOT_POINTERS from the code
and remaining config files.
Signed-off-by: David Lechner <david@pybricks.com>
This uses MP_REGISTER_ROOT_POINTER() to register mod_network_nic_list and
removes the same from all mpconfigport.h.
Signed-off-by: David Lechner <david@pybricks.com>
This uses MP_REGISTER_ROOT_POINTER() to register the readline_history root
pointer array used by shared/readline.c and removes the registration from
all mpconfigport.h files.
This also required adding a new MICROPY_READLINE_HISTORY_SIZE config option
since not all ports used the same sized array.
Signed-off-by: David Lechner <david@pybricks.com>
Replaces preprocessor macro for SDRAM option from #ifdef to #if in order to
allow always setting the define `MICROPY_HW_SDRAM_AVAIL` just with the
appropriate value 0/1. This eliminates one `if` in the Makefile.
This separates extmod source files from `py.mk`. Previously, `py.mk`
assumed that every consumer of the py/ directory also wanted to include
extmod/. However, this is not the case. For example, building mpy-cross
uses py/ but doesn't need extmod/.
This commit moves all extmod-specific items from `py.mk` to `extmod.mk` and
explicitly includes `extmod.mk` in ports that use it.
Signed-off-by: David Lechner <david@pybricks.com>
The following changes are made:
- Guard entire file with MICROPY_PY_LWIP, so it can be included in the
build while still being disabled (for consistency with other extmod
modules).
- Add modlwip.c to list of all extmod source in py/py.mk and
extmod/extmod.cmake so all ports can easily use it.
- Move generic modlwip GIT_SUBMODULES build configuration code from
ports/rp2/CMakeLists.txt to extmod/extmod.cmake, so it can be reused by
other ports.
- Remove now unnecessary inclusion of modlwip.c in EXTMOD_SRC_C in esp8266
port, and in SRC_QSTR in mimxrt port.
Signed-off-by: Damien George <damien@micropython.org>
The nxp_driver v2.10 allows for/requires some changes to the code:
- Remove some part of pwm_backlog.*, which is provided by the lib now.
- Change eth.c: the newer versions have additional parameters of the
library versions.
- Change sdcard.c: use TransferBlocking instead of TransferNonblocking.
- Add some support for the MIMXRT1176 device.
- Set the clocks for UART, I2C, Timer.
- Integrate the I2S module and fix a rebase error.
- Use blocking transfer only for SPI. It's faster and interferes less with
other modules.
- Use the clock_config.c files of library v2.8.5. The mimxrt files keeps
the clock_config.c files from Verson 2.8.5. With clock_config.c from
v2.10, the boards do not work. Refactoring of the clock set-up is on the
to-do list.
- Enable expiry timers for UART, I2C and SPI, avoiding a stall in library
code.
- The clock_config.* files are moved from the board-specific directories to
the boards directory and given a MCU related name.
It's no longer needed because this macro is now processed after
preprocessing the source code via cpp (in the qstr extraction stage), which
means unused MP_REGISTER_MODULE's are filtered out by the preprocessor.
Signed-off-by: Damien George <damien@micropython.org>
For ports with MICROPY_VFS and MICROPY_PY_IO enabled their configuration
can now be simplified to use the defaults for mp_import_stat and
mp_builtin_open.
This commit makes no functional change, except for the following minor
points:
- the built-in "open" is removed from the minimal port (it previously did
nothing)
- the duplicate built-in "input" is removed from the esp32 port
- qemu-arm now delegates to VFS import/open
Signed-off-by: Damien George <damien@micropython.org>
This replaces occurences of
foo_t *foo = m_new_obj(foo_t);
foo->base.type = &foo_type;
with
foo_t *foo = mp_obj_malloc(foo_t, &foo_type);
Excludes any places where base is a sub-field or when new0/memset is used.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Changes in this commit:
- Fix USB CDC RX handling to not block when unprocessed. The fix follows
5873390226.
- Fix dupterm rx.
- Remove some obsolete lines.
This commit changes the method of waiting for SPI being not busy. Instead
of the FIFO size, the TransferBusyFlag is probed.
Also, raise an error if the transfer failed.
Changes in this commit:
- Start the RTC Timer at system boot. Otherwise time.time() will advance
only if an RTC() object was created.
- Set the time to a more recent date than Jan 1, 1970, if not set. That is
2013/10/14, 19:53:11, MicroPython's first commit.
- Compensate an underflow in in timeutils_seconds_since_2000(), called by
time.time(), if the time is set to a pre-2000 date.
This commit adds support for machine.I2S on the mimxrt port. The I2S API
is consistent with the existing stm32, esp32, and rp2 implementations.
I2S features:
- controller transmit and controller receive
- 16-bit and 32-bit sample sizes
- mono and stereo formats
- sampling frequencies from 8kHz to 48kHz
- 3 modes of operation:
- blocking
- non-blocking with callback
- uasyncio
- configurable internal buffer
- optional MCK
Tested with the following development boards:
- MIMXRT1010_EVK, MIMXRT1015_EVK, MIMXRT1020_EVK, MIMXRT1050_EVK
- Teensy 4.0, Teensy 4.1
- Olimex RT1010
- Seeed ARCH MIX
Tested with the following I2S hardware peripherals:
- UDA1334
- GY-SPH0645LM4H
- WM8960 codec on board the MIMXRT boards and separate breakout board
- INMP441
- PCM5102
- SGTL5000 on the Teensy audio shield
Signed-off-by: Mike Teachman <mike.teachman@gmail.com>
Ensure the symmetry of PWM: the duty rate of X and Q channels was not 50%,
when it should have been. That is evident at high frequencies, like 15Mhz
or 37.5 MHz. At low frequencies the deviation mattered less. The A/B
channels were fine.
Also round up or down non-integer division factors. Before, always the
floor value was used.
That caused Ethernet to lock up at high data rates after ~200MByte data
average in a row. Tested now with data bursts up to 10 GByte and overall
data rates of ~8MByte/s at the Eth100 port.
Sometimes frames could not be sent immediately because the controller was
still busy with previous frames. Then, an error was returned to lwip.
This fix adds a limited number of retries for this busy state, waiting
100µs before the next attempt. Typically the transmit succeeds now at the
second attempt.
Second change: Reset the controller for a clean state after soft reset.
OCOTP_Init() has been removed from mphalport.c. The library files are
missing for the MIMXRT1015, and for just reading the OCOTP the Init is not
required.
The inclusion of `umachine` in the list of built-in modules is now done
centrally in py/objmodule.c. Enabling MICROPY_PY_MACHINE will include this
module.
As part of this, all ports now have `umachine` as the core module name
(previously some had only `machine` as the name).
Signed-off-by: Damien George <damien@micropython.org>
The board.json file is intentionally excluded, until the board will be
sold. But including it into the mimxrt series make it easier to keep
the build up-to-date.
- Manufacturer, set by MICROPY_HW_USB_STR_MANUF; default "MicroPython"
- Board name, as set by MICROPY_HW_BOARD_NAME
- Unique-ID, same as returned by machine.unique_id()
- USB Vendor ID, as set by MICROPY_HW_USB_VID; default 0xf055
- USB Product ID, as set by MICROPY_HW_USB_PID; default 0x9802
Using the keyword argument cs=nnn in the constructor. The cs1
pin has to be defined in mpconfigboard.h.
Note: Only a few boards have the CS1 pin exposed to the connectors.
The Pin config setting by IOMUXC_SetPinConfig() is supplied by a
bit pattern. That pattern is specific for a MCU family. In preparation
for supporting the MIMXRT117x family, the constant bit pattern is
replaced by a function call, such that the bit pattern is created
at a single place. The code for this functions was taken from
machine_pin.c.
Note: A working port for the MIMXRT1176 exists already.
This library file has a bug, in that TransferBlocking returns before the
transfer has finished. That is a problem if a write follows immediately
a read.
If in a board's mkconfigboard.mk the following symbol is set:
MICROPY_HW_BOARD_FLASH_FILES = 1
then the files:
($BOARD)_flexspi_flash_config.h and
qspi_nor_flash_config.c and/or
qspi_hyper_flash_config.c
are expected in the board directory. Otherwise the common files from
the hal directory are used.
This is needed because these ports allocate mbedtls data on the MicroPython
heap, and SSL socket objects must be fully cleaned up when they are garbage
collected, to free this memory allocated by mbedtls. As part of this,
gc_sweep_all() will now ensure that the MP_STATE_PORT(mbedtls_memory)
linked-list is fully deallocated on soft reset.
Signed-off-by: Damien George <damien@micropython.org>
If MICROPY_PY_SYS_PATH_ARGV_DEFAULTS is enabled (which it is by default)
then sys.path and sys.argv will be initialised and populated with default
values. This keeps all bare-metal ports aligned.
Signed-off-by: Damien George <damien@micropython.org>
Frozen modules will be searched preferentially, but gives the user the
ability to override this behavior.
This matches the previous behavior where "" was implicitly the frozen
search path, but the frozen list was checked before the filesystem.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
- Move the qspi_xxxx_flash_config.c files to hal.
It turned out that they are less board than flash type specific.
- Change to a common flexspi_flash_config.h header file.
Thanks for the hint, Damien. The DEBUG build got very large recently.
The major difference is, that inline function are now inlined and
not included as a function. That's good and maybe bad. The good thing is,
that the code speed si now close to the final code. It could be worse
in single step debugging. I'll see.
Setting this option caused a new warning and a formatting error
to pop up at different places. Fixed as well.
The ID is read in a single function and used for:
- machine.unique_id()
- Ethernet MAC addresses.
- ...
That facilitates use of other MCU using a different access method for
the ID (e.g. i.MX RT1176).
Just another choice for the PHY interface.
Added: Keyword option phy_clock=LAN.IN or LAN.OUT
to define the source of the 50MHZ clock for the PHY
interface. The RMII clock is not enabled if it
is generated by a PYH board. Constants:
LAN.IN The clock is provided by the PHY board.
LAN.OUT The clock is provided by the MCU board.
The default is LAN.OUT or the value set in mpconfigboard.h, which
is currently set to IN only for the SEEED ARCH MIX board. Usage etc:
lan = LAN(phy_type=LAN.PHY_DP83848, phy_clock=LAN.IN)
The initial problem with a wrong ICMP checksum was caused by
the test code setting a checksum and the HW taking that probably as
the start value and ending up with 0xffff. With a checksum field of 0
set by the test code the HW creates the proper checksum.
Useful for boards without a PHY interface, where that has to be
attached. Like the Seed ARCH MIX board or Vision SOM. Phy drivers
supported so far are:
- KSZ8081
- DP83825
- LAN8720
More to come. Usage e.g.:
lan = LAN(phy_type=LAN.PHY_LAN8720, phy_addr=1)
The default values are those set in mpconfigboard.h.
UART 0 is attached to the Debug USB port. The settings are
115200 Baud, 8N1.
For MIMXRT1010_EVK this is identical to UART1. For the other boards,
this is an additional UART.
Frequency range 15Hz/18Hz to > 1 MHz, with decreasing resolution of the
duty cycle. The basic API is supported as documentated, except that
keyword parameters are accepted for both the instatiaton and the
PWM.init() call.
Extensions: support PWM for channel pairs. Channel pairs are declared by
supplying 2-element tuples for the pins. The two channels of a pair must
be the A/B channel of a FLEXPWM module. These form than a complementary
pair.
Additional supported keyword arguments:
- center=value Defines the center position of a pulse within the pulse
cycle. The align keyword is actually shortcut for center.
- sync=True|False: If set to True, the channels will be synchronized to a
submodule 0 channel, which has already to be enabled.
- align=PWM.MIDDLE | PMW.BEGIN | PWM.END. It defines, whether synchronized
channels are Center-Aligned or Edge-aligned. The channels must be either
complementary a channel pair or a group of synchronized channels. It may
as well be applied to a single channel, but withiout any benefit.
- invert= 0..3. Controls ouput inversion of the pins. Bit 0 controls the
first pin, bit 1 the second.
- deadtime=time_ns time of complementary channels for delaying the rising
slope.
- xor=0|1|2 xor causes the output of channel A and B to be xored. If
applied to a X channel, it shows the value oif A ^ B. If applied to an A
or B channel, both channel show the xored signal for xor=1. For xor=2,
the xored signal is split between channels A and B. See also the
Reference Manual, chapter about double pulses. The behavior of xor=2 can
also be achieved using the center method for locating a pulse within a
clock period.
The output is enabled for board pins only.
CPU pins may still be used for FLEXPWM, e.g. as sync source, but the signal
will not be routed to the output. That applies only to FLEXPWM pins. The
use of QTMR pins which are not board pins will be rejected.
As part of this commit, the _WFE() statement is removed from
ticks_delay_us64() to prevent PWM glitching during calls to sleep().
- Add board.md files for MIMXRT1060_EVK and MIMXRT1064_EVK warning about
their experimental state.
- Add separate deploy_teensy.md and deploy_mimxrt.md files.
The ARCH MIX board exposes the Ethernet Pins at it's connectors. Therefore
the software is configured for using a LAN8720 PHY device. Breakout boards
with the LAN8720 are easily available.
This will be used by https://micropython.org/download/ to generate the
full listing of boards and firmware files.
Optionally supports a board.md for additional customisation of the
download page, as well as deploy.md for flashing instructions.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
By moving code to ITCM, like vm, gc, parse, runtime. The change affects
mostly the execution speed of MicroPython code. The speed is increased by
up to a factor of 6, especially for MCU with small cache.
Prior to this commit mp_hal_ticks_cpu() was not started properly. It only
started when the code was executed with a debugger attached, except for the
Teensy (i.MXRT1062) boards. As an additional fix, the CYYCNT timer is now
started at boot time.
Also rename mp_hal_ticks_cpu_init() to mp_hal_ticks_cpu_enable().
Jim Mussared