Such constants are MCU specific so shouldn't be specified in the board
config file (else it leads to too much duplication of code).
This patch also adds I2C timing values for the F767/F769 for 100k, 400k
and 1MHz I2C bus frequencies.
If an I2C send/recv fails then the peripheral is now checked to see if
it's in a "stuck" state waiting for the stop bit, and if so then it is
reset so that the next I2C transaction can proceed.
This patch also de-inits the I2C peripheral in the init() method, before
init'ing it again.
New keyword option in constructor and init() method is "dma=<bool>".
DMA is now disabled by default for I2C transfers because it currently does
not handle I2C bus errors very well (eg if slave device doesn't ACK or
NACK correctly during a transfer).
The main thing is to change the DMA code in a way that the structure
DMA_Stream_TypeDef (which is similar to DMA_Channel_TypeDef on stm32l4)
is no longer used outside of dma.c, as this structure only exists for the
F4 series. Therefore I introduced a new structure (dma_descr_t) which
handles all DMA specific stuff for configuration. Further the periphery
(spi, i2c, sdcard, dac) does not need to know the internals of the dma.
A standard I2C address is 7 bits but addresses 0b0000xxx and 0b1111xxx
are reserved. The scan() method is changed to reflect this, along with
the docs.
The first argument to the type.make_new method is naturally a uPy type,
and all uses of this argument cast it directly to a pointer to a type
structure. So it makes sense to just have it a pointer to a type from
the very beginning (and a const pointer at that). This patch makes
such a change, and removes all unnecessary casting to/from mp_obj_t.
In new hardware API, these classes implement master modes of interfaces,
and "mode" parameter is not accepted. Trying to implement new HW API
in terms of older pyb module leaves variuos corner cases:
In new HW API, I2C(1) means "I2C #1 in master mode" (? depends on
interpretation), while in old API, it means "I2C #1, with no settings
changes".
For I2C class, it's easy to make mode optional, because that's last
positional param, but for SPI, there's "baudrate" after it (which
is inconsistent with I2C, which requires "baudrate" to be kwonly-arg).
py/mphal.h contains declarations for generic mp_hal_XXX functions, such
as stdio and delay/ticks, which ports should provide definitions for. A
port will also provide mphalport.h with further HAL declarations.
Extracted GPIO clock enable logic into mp_hal_gpio_clock_enable
and called from anyplace which might need to use GPIO functions
on ports other than A-D.
Thanks to Dave Hylands for the patch.
This removes hard-coded DMA init params from dma_init(), instead defining
these parameters in a DMA_InitTypeDef struct that gets passed as an
argument to dma_init()
This makes dma_init more generic so it can be used for I2S and SD Card,
which require different initialization parameters.
Previous to this patch the printing mechanism was a bit of a tangled
mess. This patch attempts to consolidate printing into one interface.
All (non-debug) printing now uses the mp_print* family of functions,
mainly mp_printf. All these functions take an mp_print_t structure as
their first argument, and this structure defines the printing backend
through the "print_strn" function of said structure.
Printing from the uPy core can reach the platform-defined print code via
two paths: either through mp_sys_stdout_obj (defined pert port) in
conjunction with mp_stream_write; or through the mp_plat_print structure
which uses the MP_PLAT_PRINT_STRN macro to define how string are printed
on the platform. The former is only used when MICROPY_PY_IO is defined.
With this new scheme printing is generally more efficient (less layers
to go through, less arguments to pass), and, given an mp_print_t*
structure, one can call mp_print_str for efficiency instead of
mp_printf("%s", ...). Code size is also reduced by around 200 bytes on
Thumb2 archs.
With this patch str/bytes construction is streamlined. Always use a
vstr to build a str/bytes object. If the size is known beforehand then
use vstr_init_len to allocate only required memory. Otherwise use
vstr_init and the vstr will grow as needed. Then use
mp_obj_new_str_from_vstr to create a str/bytes object using the vstr
memory.
Saves code ROM: 68 bytes on stmhal, 108 bytes on bare-arm, and 336 bytes
on unix x64.
Blanket wide to all .c and .h files. Some files originating from ST are
difficult to deal with (license wise) so it was left out of those.
Also merged modpyb.h, modos.h, modstm.h and modtime.h in stmhal/.
Decided to write own script to pull documentation from comments in C code.
Style for writing auto generated documentation is: start line with ///
and then use standard markdown to write the comment. Keywords
recognised by the scraper begin with backslash. See code for examples.
Running: python gendoc.py modpyb.c accel.c adc.c dac.c extint.c i2c.c
led.c pin.c rng.c servo.c spi.c uart.c usrsw.c, will generate a HTML
structure in gendoc-out/.
gendoc.py is crude but functional. Needed something quick, and this was
it.
Damien George