This adds new compile-time infrastructure to parse source code files for
`MP_REGISTER_ROOT_POINTER()` and generates a new `root_pointers.h` header
file containing the collected declarations. This works the same as the
existing `MP_REGISTER_MODULE()` feature.
Signed-off-by: David Lechner <david@pybricks.com>
Some devices, such as the LightBlue BTLE app on iOS, try to use Bluetooth 5
when connecting to a device. This means that they will send a
BLE_GAP_EVT_PHY_UPDATE_REQUEST message to shift to a new physical layer.
If this event isn't handled, LightBlue (and likely other Bluetooth 5.0
central devices) will try to connect and then fail, staying in
"Connecting..." state forever. This message should be replied to with
sd_ble_gap_phy_update, as documented in
drivers/bluetooth/s140_nrf52_6.1.1/s140_nrf52_6.1.1_API/include/ble_gap.h.
This commit handles the event. LightBlue can now successfully connect to a
BTLE device on a P10059 nRF52840 dongle running MicroPython. Two other
related events have logging added in case they are needed in the future.
Commit 0e28a1f0e5 made it possible to set
-march=armv6m. It needs to be used when freezing for rp2.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Since nlr_jump_fail() exits the process, it can leave the terminal in raw
mode which means characters are not echoed. Fix this by restoring the
original terminal mode.
Signed-off-by: David Lechner <david@pybricks.com>
When a flash write/erase is in progress, we need to ensure that the
other core cannot be using XIP.
This also implements MICROPY_BEGIN_ATOMIC_SECTION as a full mutex, which
is necessary as it's used to syncronise access to things like the scheduler
queue.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The goal is to avoid a situation where core 1 is shut down while holding
the tinyusb spinlock, which could happen during soft reset if
mp_thread_deinit is called while core1 is running tud_task().
This also fixes a latent race where the two cores are competing to
decrement and compare `vm_hook_divisor` with no mem fence or atomic
protection -- only core0 will now do this.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
To override it a board must define MICROPY_BOARD_FATAL_ERROR to a function
that takes a string message and does not return.
Signed-off-by: Damien George <damien@micropython.org>
The file `ports/unix/moduos.c` uses `errno` so it needs to include
`errno.h`, otherwise a compiler error can occur.
Signed-off-by: David Lechner <david@pybricks.com>
Ensure that nimble and cyw43-driver are initialised when the board requires
it. Also make these work with `make submodules`.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Commit 9670a156da missed one renaming of
MICROPY_PY_WIZNET5K to MICROPY_PY_NETWORK_WIZNET5K which prevented the
Wiznet interface from being enabled.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This includes:
- Configuration file for the cyw43-driver.
- Integration of cyw43-driver into the build, using lwIP.
- Enhancements to machine.Pin to support extension IO pins provided by the
CYW43xx.
- More mp-hal pin helper functions.
- mp_hal_get_mac_ascii MAC address helper function.
- Addition of rp2.country() function to set the country code.
A board can enable this driver by setting MICROPY_PY_NETWORK_CYW43 in their
cmake snippet.
Work done in collaboration with Graham Sanderson and Peter Harper.
Signed-off-by: Damien George <damien@micropython.org>
It is more reliable and scales better when more components need it.
Work done in collaboration with Graham Sanderson and Peter Harper.
Signed-off-by: Damien George <damien@micropython.org>
Prior to this commit the following code would lock up the device when
Ctrl-D is entered at the REPL:
import gc, _thread
def collect_thread():
while True:
gc.collect()
_thread.start_new_thread(collect_thread, [])
Fixes part of #8494.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This gets basic machine.lightsleep([n]) behaviour working on the rp2 port.
It supports:
- Calling lightsleep without a specified period, in which case it uses xosc
dormant mode. There's currently no way to wake it up from this state,
unless you write to raw registers to enable a GPIO wake up source.
- Calling lightsleep with a period n in milliseconds. This period must be
less than about 72 minutes and uses timer alarm3 to wake it up.
The RTC continues to run during lightsleep, but other peripherals have
their clock turned off during the sleep.
It doesn't yet support longer periods than 72 minutes, or waking up from
GPIO IRQ.
Measured current consumption from the USB port on a PICO board is about
1.5mA when doing machine.lightsleep(5000), and about 0.9mA when doing
machine.lightsleep().
Addresses issue #8770.
Signed-off-by: Damien George <damien@micropython.org>
This ROM level is not yet fully defined, but it at least enables
MICROPY_PY_SYS_TRACEBACKLIMIT. The coverage build should have everything
enabled, so it makes sense to use this ROM level for it.
Signed-off-by: Damien George <damien@micropython.org>
So that the default configuration for the dev and coverage variants
includes all options set by MICROPY_CONFIG_ROM_LEVEL_EXTRA_FEATURES.
Note that enabling MICROPY_PY_SYS_STDIO_BUFFER on unix doesn't do anything
because unix doesn't use shared/runtime/sys_stdio_mphal.c.
Signed-off-by: Damien George <damien@micropython.org>
The default is the same as before: MICROPY_PY_USELECT=0 and
MICROPY_PY_USELECT_POSIX=1. But now this can be easily overridden at the
make command-line using, eg:
make VARIANT=dev CFLAGS_EXTRA=-DMICROPY_PY_USELECT=1
Signed-off-by: Damien George <damien@micropython.org>
Prior to this commit, running scan() without any APs available would give:
>>> wl.scan()
Traceback (most recent call last):
File "<stdin>", line 1, in <module>
RuntimeError: Wifi Unknown Error 0x0102
Signed-off-by: Damien George <damien@micropython.org>
When tested, this reduces default MP binary sizes by approx 2-2.5%, and
very marginally increases performance in benchmarks. Build times seem very
similar to non-LTO when using gcc 12.
See #8733 for further discussion.
Signed-off-by: Angus Gratton <gus@projectgus.com>
Prerequisite for enabling Link Time Optimisation.
The _bl_state address is the same as _estack, but _estack is referred to as
a uint32_t elsewhere in the code. LTO doesn't like it when the same symbol
has two different types.
Signed-off-by: Angus Gratton <gus@projectgus.com>
Replaces preprocessor macro for SDRAM option from #ifdef to #if in order to
allow always setting the define `MICROPY_HW_SDRAM_AVAIL` just with the
appropriate value 0/1. This eliminates one `if` in the Makefile.
Add esp32.wake_on_ulp() to give access to esp_sleep_enable_ulp_wakeup(),
which is needed to allow the ULP co-processor to wake the main CPU from
deep sleep.
Allow esp32.ULP.load_binary() to use the maximum amount of memory available
again, which is 2040 bytes unless MICROPY_HW_RTC_USER_MEM_MAX is
customized.
This value regressed in 3d49b157b8
Using it for the rx-timeout. The value is given as ms, which is then
converted to character times. A value of less than a character time will
cause the rx call to return immediately after 1 character, which may be
inefficient at high transmission rates.
Addresses #8778.
This separates extmod source files from `py.mk`. Previously, `py.mk`
assumed that every consumer of the py/ directory also wanted to include
extmod/. However, this is not the case. For example, building mpy-cross
uses py/ but doesn't need extmod/.
This commit moves all extmod-specific items from `py.mk` to `extmod.mk` and
explicitly includes `extmod.mk` in ports that use it.
Signed-off-by: David Lechner <david@pybricks.com>
The following changes are made:
- Guard entire file with MICROPY_PY_LWIP, so it can be included in the
build while still being disabled (for consistency with other extmod
modules).
- Add modlwip.c to list of all extmod source in py/py.mk and
extmod/extmod.cmake so all ports can easily use it.
- Move generic modlwip GIT_SUBMODULES build configuration code from
ports/rp2/CMakeLists.txt to extmod/extmod.cmake, so it can be reused by
other ports.
- Remove now unnecessary inclusion of modlwip.c in EXTMOD_SRC_C in esp8266
port, and in SRC_QSTR in mimxrt port.
Signed-off-by: Damien George <damien@micropython.org>
The WLAN.config() method now supports "ssid", "security" and "key" as
aliases to the existing "essid", "authmode" and "password", which are now
deprecated. The help text and setup helper are also updated.
Addresses issue #8083.
The WLAN.config() method now supports "ssid", "security" and "key" as
aliases to the existing "essid", "authmode" and "password", which are now
deprecated.
Addresses issue #8083.
Updates the Zephyr port build instructions and CI to use the latest Zephyr
release tag.
Tested on frdm_k64f.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
When MICROPY_PY_MACHINE_I2C_TRANSFER_WRITE1 is enabled the port's hardware
I2C transfer functions should support the MP_MACHINE_I2C_FLAG_WRITE1
option, but software I2C will not. So add a flag to the I2C protocol
struct so each individual protocol can indicate whether it supports this
option or not.
Fixes issue #8765.
Signed-off-by: Damien George <damien@micropython.org>
Both led_init and led_state are configurable via MBOOT_BOARD_LED_INIT and
MBOOT_BOARD_LED_STATE respectively, so don't need to be MP_WEAK.
Furthermore, led_state and led0_state are private to ui.c so can be made
static.
Signed-off-by: Damien George <damien@micropython.org>
This IO was enabled in IDF commit 68f8b999bb69563f2f3d1d897bc073968f41f3bf,
which is available in IDF release v4.3.2 and above.
Signed-off-by: Damien George <damien@micropython.org>
Otherwise include directories are added unconditionally to the build
variables if the component (submodule) is checked out. This can lead to,
eg, the esp32 build using lib/lwip header files, instead of lwip header
files from the IDF.
Fixes issue #8727.
Signed-off-by: Damien George <damien@micropython.org>
System config block contains hardware unrelated to USB. So calling
`__SYSCFG_CLK_DISABLE()` during `HAL_PCD_MspDeInit()` has an adverse effect
on other system functionality.
Removing call to `__SYSCFG_CLK_DISABLE()` to rectify this issue.
This call was there since the beginning of the USB CDC code, added in
b30c02afa0.
According to ST Errata ES0206 Rev 18, Section 2.2.1, on STM32F427x,
STM32F437x, STM32F429x and STM32F439x.
If the system tick interrupt is enabled during stop mode while certain
bits are set in the DBGMCU_CR, then the system will immediately wake
from stop mode.
Suggested workaround is to disable system tick timer interrupt when
entering stop mode.
According to ST Errate ES0394 Rev 11, Section 2.2.17, on STM32WB55Cx and
STM32WB35Cx.
If the system tick interrupt is enabled during stop 0, stop 1 or stop 2
while certain bits are set in DBGMCU_CR, then system will immediately
wake from stop mode but the system remains in low power state. The CPU
therefore fetches incorrect data from inactive Flash, which can cause a
hard fault.
Suggested workaround is to disable system tick timer interrupt when
entering stop mode.
This was added by mistake in 8f68e26f79 when
adding support for G4 MCUs, which does not using this get_bank() function.
FLASH_OPTR_DBANK is only defined on G4 and L4 MCUs, so on H7 this
FLASH_BANK_2 code was being wrongly excluded.
Signed-off-by: Damien George <damien@micropython.org>
Also remove redundant modusocket.c and modnetwork.c sources, they are
already added by extmod/extmod.cmake.
Signed-off-by: Damien George <damien@micropython.org>
The callback passed to add_alarm_in_ms must return microseconds, even
though the initial delay is in milliseconds. Fix this use, and to avoid
further confusion use the add_alarm_in_us function instead.
Signed-off-by: Damien George <damien@micropython.org>
The nxp_driver v2.10 allows for/requires some changes to the code:
- Remove some part of pwm_backlog.*, which is provided by the lib now.
- Change eth.c: the newer versions have additional parameters of the
library versions.
- Change sdcard.c: use TransferBlocking instead of TransferNonblocking.
- Add some support for the MIMXRT1176 device.
- Set the clocks for UART, I2C, Timer.
- Integrate the I2S module and fix a rebase error.
- Use blocking transfer only for SPI. It's faster and interferes less with
other modules.
- Use the clock_config.c files of library v2.8.5. The mimxrt files keeps
the clock_config.c files from Verson 2.8.5. With clock_config.c from
v2.10, the boards do not work. Refactoring of the clock set-up is on the
to-do list.
- Enable expiry timers for UART, I2C and SPI, avoiding a stall in library
code.
- The clock_config.* files are moved from the board-specific directories to
the boards directory and given a MCU related name.
It's no longer needed because this macro is now processed after
preprocessing the source code via cpp (in the qstr extraction stage), which
means unused MP_REGISTER_MODULE's are filtered out by the preprocessor.
Signed-off-by: Damien George <damien@micropython.org>
This cleans up the parsing of MP_REGISTER_MODULE() and generation of
genhdr/moduledefs.h so that it uses the same process as compressed error
string messages, using the output of qstr extraction.
This makes sure all MP_REGISTER_MODULE()'s that are part of the build are
correctly picked up. Previously the extraction would miss some (eg if you
had a mod.c file in the board directory for an stm32 board).
Build speed is more or less unchanged.
Thanks to @stinos for the ports/windows/msvc/genhdr.targets changes.
Signed-off-by: Damien George <damien@micropython.org>
The following changes are made:
- Use software SPI for external SPI flash access when building mboot.
- Enable the mboot filesystem-loading feature, with FAT FS support.
- Increase the frequency of the CPU when in mboot to 96MHz, to increase the
speed of SPI flash accesses and programming.
Signed-off-by: Damien George <damien@micropython.org>
This allows a board to modify initial_r0 if needed.
Also make default board behaviour functions always available, named as
mboot_get_reset_mode_default and mboot_state_change_default.
Signed-off-by: Damien George <damien@micropython.org>
I2C transfers are much more efficient if they are combined, instead of
doing separate writes and reads.
Fixes issue #7134.
Signed-off-by: Damien George <damien@micropython.org>
This follows on from a5324a1074 and allows
mpy-cross to dynamically select whether ARMv7-M instructions are supported
in @micropython.asm_thumb functions.
The config option MICROPY_EMIT_INLINE_THUMB_ARMV7M is no longer needed, it
is now controlled by MICROPY_EMIT_THUMB_ARMV7M.
Signed-off-by: Damien George <damien@micropython.org>
For ports with MICROPY_VFS and MICROPY_PY_IO enabled their configuration
can now be simplified to use the defaults for mp_import_stat and
mp_builtin_open.
This commit makes no functional change, except for the following minor
points:
- the built-in "open" is removed from the minimal port (it previously did
nothing)
- the duplicate built-in "input" is removed from the esp32 port
- qemu-arm now delegates to VFS import/open
Signed-off-by: Damien George <damien@micropython.org>
The following changes are made:
- If MICROPY_VFS is enabled then mp_vfs_import_stat and mp_vfs_open are
automatically used for mp_import_stat and mp_builtin_open respectively.
- If MICROPY_PY_IO is enabled then "open" is automatically included in the
set of builtins, and points to mp_builtin_open_obj.
This helps to clean up and simplify the most common port configuration.
Signed-off-by: Damien George <damien@micropython.org>
This reverts commit 2668337f36.
The issue with potential breaking of the BLE RX path in the radio is fixed
since WS v1.12.0.
Signed-off-by: Damien George <damien@micropython.org>
This adds a new command line option to the unix port `-X realtime` to
enable realtime priority on threads. This enables high precision timers
for applications that need more accurate timers.
Related docs:
https://developer.apple.com/library/archive/technotes/tn2169/_index.html
Fixes issue #8621.
Signed-off-by: David Lechner <david@pybricks.com>
This adds the `mp_` prefix to the `thread_t` type. The name `thread_t`
conflicts with the same in `mach/mach_types.h` on macOS.
Signed-off-by: David Lechner <david@lechnology.com>
Reasons for removal:
- It did not work properly because it stopped the hardware watchdog
timer while keeping the software watchdog running (issue #8597).
- There isn't a deinit method for the WDT in any other port.
- "The watchdog is not intended to be stopped. That is a feature."
(See #8600.)
Replace the timer-based sleep with the standard win32 call since the former
has no benefits: even though it allows specifying the time in 100uSec
chunks, the actual resolution is still limited by the OS and is never
better than 1mSec.
For clarity move all of this next to the mp_hal_delay_ms definition so all
related functions are in one place.
This replaces occurences of
foo_t *foo = m_new_obj(foo_t);
foo->base.type = &foo_type;
with
foo_t *foo = mp_obj_malloc(foo_t, &foo_type);
Excludes any places where base is a sub-field or when new0/memset is used.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
* Change device name table to list style to show properly.
* Change the link of cable connection information to the latest.
Signed-off-by: Takeo Takahashi <takeo.takahashi.xv@renesas.com>
This contains a string useful for identifying the underlying machine. This
string is kept consistent with the second part of the REPL banner via the
new config option MICROPY_BANNER_MACHINE.
This makes os.uname() more or less redundant, as all the information in
os.uname() is now available in the sys module.
Signed-off-by: Damien George <damien@micropython.org>
This commit adds the git hash and build date to sys.version. This is
allowed according to CPython docs, and is what PyPy does. The docs state:
A string containing the version number of the Python interpreter plus
additional information on the build number and compiler used.
Eg on CPython:
Python 3.10.4 (main, Mar 23 2022, 23:05:40) [GCC 11.2.0] on linux
Type "help", "copyright", "credits" or "license" for more information.
>>> import sys
>>> sys.version
'3.10.4 (main, Mar 23 2022, 23:05:40) [GCC 11.2.0]'
and PyPy:
Python 2.7.12 (5.6.0+dfsg-4, Nov 20 2016, 10:43:30)
[PyPy 5.6.0 with GCC 6.2.0 20161109] on linux2
Type "help", "copyright", "credits" or "license" for more information.
>>>> import sys
>>>> sys.version
'2.7.12 (5.6.0+dfsg-4, Nov 20 2016, 10:43:30)\n[PyPy 5.6.0 with GCC ...
With this commit on MicroPython we now have:
MicroPython v1.18-371-g9d08eb024 on 2022-04-28; linux [GCC 11.2.0] v...
Use Ctrl-D to exit, Ctrl-E for paste mode
>>> import sys
>>> sys.version
'3.4.0; MicroPython v1.18-371-g9d08eb024 on 2022-04-28'
Note that the start of the banner is the same as the end of sys.version.
This helps to keep code size under control because the string can be reused
by the compiler.
Signed-off-by: Damien George <damien@micropython.org>
This commit adds a board definition for NUCLEO_G0B1RE. This board has the
REPL on UART2 which is connected to the on-board ST-link USB-UART.
Signed-off-by: Asensio Lorenzo Sempere <asensio.aerospace@gmail.com>
This implements self-triggering of the Flash NVIC interrupt on Cortex-M0
devices, which allows enabling internal storage on those MCUs.
Signed-off-by: Asensio Lorenzo Sempere <asensio.aerospace@gmail.com>
These files that are reformatted only now fall under the list of files to
apply uncrustify/black formatting to.
Signed-off-by: Damien George <damien@micropython.org>
To avoid any I/O glitches in mp_hal_pin_config, make sure a valid alternate
function is set in AFR first before switching the pin mode. When switching
from AF to INPUT or OUTPUT, the AF in AFR will remain valid up until the
pin mode is switched.
David Lechner