The legacy I2S "shim" is removed and replaced by the new I2S driver. The
new driver fixes a bug where mono audio plays only in one channel.
Application code size is reduced by 2672 bytes with this change. Tested on
ESP32, ESP32+spiram, ESP32-S3 using example code from
https://github.com/miketeachman/micropython-i2s-examples
Signed-off-by: Mike Teachman <mike.teachman@gmail.com>
The Python BLE IRQ handler will most likely run on the NimBLE task, so its
C stack must be large enough to accommodate reasonably complicated Python
code (eg a few call depths). So increase this stack size.
Also increase the headroom from 1024 to 2048 bytes. This is needed because
(1) the esp32 architecture uses a fair amount of stack in general; and (2)
by the time execution gets to setting the Python stack top via
`mp_stack_set_top()` in this interlock code, about 600 bytes of stack are
already used, which reduces the amount available for Python.
Fixes issue #12349.
Signed-off-by: Damien George <damien@micropython.org>
The standard Arduino pinout uses LEDR/G/B and LED_BUILTIN (if available).
This patch adds aliases to match the standard pinout, while retaining
LED_RED/GREEN/BLUE for compatibility with existing scripts and examples.
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
Instead, configure the default once at compile-time. This means the GAP
name will no longer be set to default after re-initializing Bluetooth.
Signed-off-by: Daniël van de Giessen <daniel@dvdgiessen.nl>
Disable unused EC curves and default certificate bundle which is not
implemented in MicroPython. This reduces the firmware size significantly.
This follows commit 68f166dae9.
Signed-off-by: Carlos Gil Gonzalez <carlosgilglez@gmail.com>
The installation instructions for ESP32 TinyPICO board contained a typo
that used a non-standard baud rate 912600 instead of 921600. This made the
upload command fail on some Windows computers.
Signed-off-by: Scott Zhao <zhaomh1998@outlook.com>
The amount of free IRAM in ESP32 SPIRAM builds is very small and went over
the limit due to commit 30b0ee34d3. This
commit enables further optimisations to reduce IRAM usage.
Signed-off-by: Damien George <damien@micropython.org>
At some point the config changed such that no messages above Error level
were compiled into the final binary.
Fixes issue #12815.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
This commit changes the Arduino board identifiers to correspond to their
official names. This helps to identify boards at runtime. At the moment
the Arduino Portenta H7 is reported as PORTENTA which is unfortunate as now
there is another Portenta board (Portenta C33) supported in MicroPython.
Also made the other identifiers for flash and network name consistent,
removed the incorrectly used MICROPY_PY_SYS_PLATFORM identifiers, and added
missing MICROPY_PY_NETWORK_HOSTNAME_DEFAULT identifiers.
Boards affected:
- stm32: ARDUINO_PORTENTA_H7, ARDUINO_GIGA, ARDUINO_NICLA_VISION
- renesas-ra: ARDUINO_PORTENTA_C33
- esp32: ARDUINO_NANO_ESP32
- rp2: ARDUINO_NANO_RP2040_CONNECT
Signed-off-by: Sebastian Romero <s.romero@arduino.cc>
For now, this implements the functionality required for esp32 and rp2,
including support for numeric pins, rp2 alternate functions, and rp2
extended pins.
This also updates the rp2 port to use the same structure for pins.h and
pins.csv as for esp32, and moves the pin definitions directly into the
table (rather than having a table of pointers), which is a small code size
improvement.
Support for "hidden" pins in pins.csv is added (matching the stm32
implementation).
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
All ports now use `--board-csv`, `--prefix`, `--output-souce`,
`--output-header` and no longer write to stdout. This matches the esp32
implementation.
Ports that have an AF input use `--af-csv` (to match `--board-csv`).
Any additional output files are now prefixed with `output-` (e.g.
`--output-af-const`).
Default arguments are removed (all makefiles should always specify all
arguments, using default values is likely an error).
Replaced the `af-defs-cmp-strings` and `hdr-obj-decls` args for stm32 with
just `mboot-mode`. Previously they were set on the regular build, now the
logic is reversed so mboot sets it.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Commit c4e63ace66 enabled the SPI Ethernet
driver and that cost about 13k of firwmare size, pushing the firmware over
the limit of the D2WD and OTA board variants available size.
To fix, disable SPI Ethernet on the D2WD variant, and build the OTA variant
with size optimisation rather than performance optimisation.
Signed-off-by: Damien George <damien@micropython.org>
SPI support was not enabled, and was not adapted for esp-idf v5.x. This
change enables SPI ethernet for all boards and adapts the code for esp-idf
v5.x. The change follows the sample implementation of @hemakumarm72, but
adds the changes for the other adapters as well. Further, it simplifies
the code by removing actions from netwwork_lan.c which are done in the
esp-idf drivers later, like setting the default values for .command_bits
and .address_bits, and registering the SPI interface.
Tested with a Wiznet W5500 breakout.
Signed-off-by: robert-hh <robert@hammelrath.com>
The machine_i2c_type, machine_spi_type and machine_timer_type symbols are
already declared in extmod/modmachine.h and should not be declared anywhere
else.
Also move declarations of machine_pin_type and machine_rtc_type to the
common header in extmod.
Signed-off-by: Damien George <damien@micropython.org>
Also remove corresponding commented line from esp8266/boards/manifest.py.
It doesn't have enough flash to have this frozen by default.
Signed-off-by: Glenn Moloney <glenn.moloney@gmail.com>
The IDF-provided version of TinyUSB defaults to Espressif's standard
VID:PID unless specific sdkconfig options are present. The numbers
already defined for the CUSTOM_* config options were ignored otherwise.
Signed-off-by: Luca Burelli <l.burelli@arduino.cc>
Add "CONFIG_BOOTLOADER_APP_ROLLBACK_ENABLE=y" to
ports/esp32/boards/sdkconfig.base so that all micropython esp32 images
support OTA rollback in the bootloader. These images can then be converted
to OTA-capable images as required by user tools.
Also remove CONFIG_BOOTLOADER_APP_ROLLBACK_ENABLE=y from board-specific
sdkconfig files as this is now the default.
Signed-off-by: Glenn Moloney <glenn.moloney@gmail.com>
Applies to newly-added ARDUINO_PORTENTA_C33 and UM_NANOS3.
Makes the list match the standard features defined in
24a6e951ec.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
sdkconfig.base: Add CONFIG_BOOTLOADER_SKIP_VALIDATE_IN_DEEP_SLEEP=y.
This reduces time to boot from deepsleep by at least 200ms and can
provide significant power savings for deepsleep-based battery
applications.
docs/library/esp32.rst: Add note cautioning not to enter deepsleep after
changing the boot partition, without first performing a hard reset.
Signed-off-by: Glenn Moloney <glenn.moloney@gmail.com>
This should have been added in 4815af75bc
when the variants were combined. The original non-USB variant got this
implicitly, and therefore was not in mpconfigvariant.h
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Board names need to be unique across ports, and GENERIC clashes with
the ESP8266 (which will be renamed to ESP8266_GENERIC).
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This was used to override the firmware filename generated by the build
server (to match the historical name before board definitions existed).
Now we're making everything use the board definition name (i.e. the
directory name).
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This is to support a future change to add the variant name to the build
directory and therefore should be the same style as the board name.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
To be consistent with the other partitions files (which have the "-
{2,8,16,32}MiB" suffix). Also renames partitions-ota.csv.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Unsure of the history of the ESP32_S2_WROVER board (and why it wasn't
named GENERIC_S2_...) but now it's a variant of the generic S2 board.
Also removes the non-existent CONFIG_USB_AND_UART from all S2 boards.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
As the IDF no longer supports earlier revisions of the C3 by default, we
now just explicitly support rev 3+ and enable USB (which wasn't supported
in earlier revisions).
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Also shrinks the "prefer internal" threshold to 8KB, any allocation larger
than this will try PSRAM first.
Change the mbedTLS config to use regular malloc() as well, instead of
internal only. The default is set to internal-only due to to potential
physical security issue of readout via PSRAM on the original ESP32.
However, as MicroPython runs from plaintext flash and all other context is
in the MP heap of PSRAM then it's hard to see how worsens physical security
for MP.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
This commit:
- Finds a common set of board feature tags and maps existing features to
that reduced set.
- Removes some less-useful board feature tags.
- Ensures all MCUs are specified correctly.
- Ensures all boards have a vendor (and fixes some vendor names).
This is to make the downloads page show a less intimidating set of filters.
Work done in conjunction with Matt Trentini <matt.trentini@gmail.com>.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Listing the IDF version number in the board description is not as important
as it once was, when the IDF was still undergoing a lot of changes. Now,
all builds use IDF 5.x and it's possible to query the exact version with
platform.platform().
Signed-off-by: Damien George <damien@micropython.org>
This adds named-pins support to the esp32 port, following other ports.
Since the name of esp32 CPU pins is just GPIOx, where x is an integer, the
Pin.cpu dict is not supported and CPU pins are just retrieved via their
existing integer "name" (the cost of adding Pin.cpu is about 800 bytes,
mostly due to the additional qstrs).
What this commit supports is the Pin.board dict and constructing a pin by
names given by a board. These names are defined in a pins.csv file at the
board level. If no such file exists then Pin.board exists but is empty.
As part of this commit, pin and pin IRQ objects are optimised to reduce
their size in flash (by removing their gpio_num_t entry). The net change
in firmware size for this commit is about -132 bytes.
Signed-off-by: Damien George <damien@micropython.org>
MikeTeachman