diff --git a/ports/stm32/boards/NUCLEO_F091RC/mpconfigboard.h b/ports/stm32/boards/NUCLEO_F091RC/mpconfigboard.h
new file mode 100644
index 0000000000..3546d521bf
--- /dev/null
+++ b/ports/stm32/boards/NUCLEO_F091RC/mpconfigboard.h
@@ -0,0 +1,59 @@
+#define MICROPY_HW_BOARD_NAME       "NUCLEO-F091RC"
+#define MICROPY_HW_MCU_NAME         "STM32F091RCT6"
+
+#define MICROPY_EMIT_THUMB          (0)
+#define MICROPY_EMIT_INLINE_THUMB   (0)
+#define MICROPY_PY_USOCKET          (0)
+#define MICROPY_PY_NETWORK          (0)
+#define MICROPY_PY_STM              (0)
+#define MICROPY_PY_PYB_LEGACY       (0)
+#define MICROPY_VFS_FAT             (0)
+
+#define MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE (0)
+#define MICROPY_HW_ENABLE_RTC       (1)
+#define MICROPY_HW_ENABLE_ADC       (1)
+#define MICROPY_HW_ENABLE_DAC       (1)
+#define MICROPY_HW_ENABLE_TIMER     (1)
+#define MICROPY_HW_HAS_SWITCH       (1)
+
+// For system clock, board uses internal 48MHz, HSI48
+
+// The board has an external 32kHz crystal
+#define MICROPY_HW_RTC_USE_LSE      (1)
+
+// UART config
+#define MICROPY_HW_UART1_TX     (pin_B6)
+#define MICROPY_HW_UART1_RX     (pin_B7)
+#define MICROPY_HW_UART2_TX     (pin_A2)
+#define MICROPY_HW_UART2_RX     (pin_A3)
+
+// USART2 is connected to the ST-LINK USB VCP
+#define MICROPY_HW_UART_REPL PYB_UART_2
+#define MICROPY_HW_UART_REPL_BAUD 115200
+
+// I2C busses
+#define MICROPY_HW_I2C1_SCL (pin_B8)        // Arduino D15, pin 3 on CN10
+#define MICROPY_HW_I2C1_SDA (pin_B9)        // Arduino D14, pin 5 on CN10
+#define MICROPY_HW_I2C2_SCL (pin_B10)       // Arduino D6,  pin 25 on CN10
+#define MICROPY_HW_I2C2_SDA (pin_B11)       //              pin 18 on CN10
+
+// SPI busses
+#define MICROPY_HW_SPI1_NSS     (pin_A15)   //              pin 17 on CN7
+#define MICROPY_HW_SPI1_SCK     (pin_A5)    // Arduino D13, pin 11 on CN10
+#define MICROPY_HW_SPI1_MISO    (pin_A6)    // Arduino D12, pin 13 on CN10
+#define MICROPY_HW_SPI1_MOSI    (pin_A7)    // Arduino D11, pin 15 on CN10
+#define MICROPY_HW_SPI2_NSS     (pin_B12)   //              pin 16 on CN10
+#define MICROPY_HW_SPI2_SCK     (pin_B13)   //              pin 30 on CN10
+#define MICROPY_HW_SPI2_MISO    (pin_B14)   //              pin 28 on CN10
+#define MICROPY_HW_SPI2_MOSI    (pin_B15)   //              pin 26 on CN10
+
+// USER B1 has a pull-up and is active low
+#define MICROPY_HW_USRSW_PIN        (pin_C13)
+#define MICROPY_HW_USRSW_PULL       (0)
+#define MICROPY_HW_USRSW_EXTI_MODE  (GPIO_MODE_IT_FALLING)
+#define MICROPY_HW_USRSW_PRESSED    (0)
+
+// NUCLEO-64 has one user LED
+#define MICROPY_HW_LED1             (pin_A5) // green
+#define MICROPY_HW_LED_ON(pin)      (mp_hal_pin_high(pin))
+#define MICROPY_HW_LED_OFF(pin)     (mp_hal_pin_low(pin))
diff --git a/ports/stm32/boards/NUCLEO_F091RC/mpconfigboard.mk b/ports/stm32/boards/NUCLEO_F091RC/mpconfigboard.mk
new file mode 100644
index 0000000000..1d66f7e6b6
--- /dev/null
+++ b/ports/stm32/boards/NUCLEO_F091RC/mpconfigboard.mk
@@ -0,0 +1,7 @@
+MCU_SERIES = f0
+CMSIS_MCU = STM32F091xC
+AF_FILE = boards/stm32f091_af.csv
+LD_FILES = boards/stm32f091xc.ld boards/common_basic.ld
+
+# Don't include default frozen modules because MCU is tight on flash space
+FROZEN_MPY_DIR ?=
diff --git a/ports/stm32/boards/NUCLEO_F091RC/pins.csv b/ports/stm32/boards/NUCLEO_F091RC/pins.csv
new file mode 100644
index 0000000000..33f9628bb4
--- /dev/null
+++ b/ports/stm32/boards/NUCLEO_F091RC/pins.csv
@@ -0,0 +1,50 @@
+A0,PA0
+A1,PA1
+A2,PA2
+A3,PA3
+A4,PA4
+A5,PA5
+A6,PA6
+A7,PA7
+A8,PA8
+A9,PA9
+A10,PA10
+A11,PA11
+A12,PA12
+A13,PA13
+A14,PA14
+A15,PA15
+B0,PB0
+B1,PB1
+B2,PB2
+B3,PB3
+B4,PB4
+B5,PB5
+B6,PB6
+B7,PB7
+B8,PB8
+B9,PB9
+B10,PB10
+B11,PB11
+B12,PB12
+B13,PB13
+B14,PB14
+B15,PB15
+C0,PC0
+C1,PC1
+C2,PC2
+C3,PC3
+C4,PC4
+C5,PC5
+C6,PC6
+C7,PC7
+C8,PC8
+C9,PC9
+C10,PC10
+C11,PC11
+C12,PC12
+C13,PC13
+C14,PC14
+C15,PC15
+USER_B1,PC13
+LED_GREEN,PA5
diff --git a/ports/stm32/boards/NUCLEO_F091RC/stm32f0xx_hal_conf.h b/ports/stm32/boards/NUCLEO_F091RC/stm32f0xx_hal_conf.h
new file mode 100644
index 0000000000..4e4ab9dbfa
--- /dev/null
+++ b/ports/stm32/boards/NUCLEO_F091RC/stm32f0xx_hal_conf.h
@@ -0,0 +1,314 @@
+/**
+  ******************************************************************************
+  * @file    stm32f0xx_hal_conf_template.h
+  * @author  MCD Application Team
+  * @brief   HAL configuration template file.
+  *          This file should be copied to the application folder and renamed
+  *          to stm32f0xx_hal_conf.h.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; COPYRIGHT(c) 2016 STMicroelectronics</center></h2>
+  *
+  * Redistribution and use in source and binary forms, with or without modification,
+  * are permitted provided that the following conditions are met:
+  *   1. Redistributions of source code must retain the above copyright notice,
+  *      this list of conditions and the following disclaimer.
+  *   2. Redistributions in binary form must reproduce the above copyright notice,
+  *      this list of conditions and the following disclaimer in the documentation
+  *      and/or other materials provided with the distribution.
+  *   3. Neither the name of STMicroelectronics nor the names of its contributors
+  *      may be used to endorse or promote products derived from this software
+  *      without specific prior written permission.
+  *
+  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+  * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+  * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+  * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+  * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F0xx_HAL_CONF_H
+#define __STM32F0xx_HAL_CONF_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Exported types ------------------------------------------------------------*/
+/* Exported constants --------------------------------------------------------*/
+
+/* ########################## Module Selection ############################## */
+/**
+  * @brief This is the list of modules to be used in the HAL driver
+  */
+#define HAL_MODULE_ENABLED
+#define HAL_ADC_MODULE_ENABLED
+#define HAL_CAN_MODULE_ENABLED
+#define HAL_CEC_MODULE_ENABLED
+#define HAL_COMP_MODULE_ENABLED
+#define HAL_CORTEX_MODULE_ENABLED
+#define HAL_CRC_MODULE_ENABLED
+#define HAL_DAC_MODULE_ENABLED
+#define HAL_DMA_MODULE_ENABLED
+#define HAL_FLASH_MODULE_ENABLED
+#define HAL_GPIO_MODULE_ENABLED
+#define HAL_I2C_MODULE_ENABLED
+#define HAL_I2S_MODULE_ENABLED
+#define HAL_IRDA_MODULE_ENABLED
+#define HAL_IWDG_MODULE_ENABLED
+#define HAL_PCD_MODULE_ENABLED
+#define HAL_PWR_MODULE_ENABLED
+#define HAL_RCC_MODULE_ENABLED
+#define HAL_RTC_MODULE_ENABLED
+#define HAL_SMARTCARD_MODULE_ENABLED
+#define HAL_SMBUS_MODULE_ENABLED
+#define HAL_SPI_MODULE_ENABLED
+#define HAL_TIM_MODULE_ENABLED
+#define HAL_TSC_MODULE_ENABLED
+#define HAL_UART_MODULE_ENABLED
+#define HAL_USART_MODULE_ENABLED
+#define HAL_WWDG_MODULE_ENABLED
+
+/* ######################### Oscillator Values adaptation ################### */
+/**
+  * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
+  *        This value is used by the RCC HAL module to compute the system frequency
+  *        (when HSE is used as system clock source, directly or through the PLL).
+  */
+#if !defined  (HSE_VALUE)
+  #define HSE_VALUE            ((uint32_t)8000000)  /*!< Value of the External oscillator in Hz */
+#endif /* HSE_VALUE */
+
+/**
+  * @brief In the following line adjust the External High Speed oscillator (HSE) Startup
+  *        Timeout value
+  */
+#if !defined  (HSE_STARTUP_TIMEOUT)
+  #define HSE_STARTUP_TIMEOUT  100U      /*!< Time out for HSE start up, in ms */
+#endif /* HSE_STARTUP_TIMEOUT */
+
+/**
+  * @brief Internal High Speed oscillator (HSI) value.
+  *        This value is used by the RCC HAL module to compute the system frequency
+  *        (when HSI is used as system clock source, directly or through the PLL).
+  */
+#if !defined  (HSI_VALUE)
+  #define HSI_VALUE            8000000U  /*!< Value of the Internal oscillator in Hz*/
+#endif /* HSI_VALUE */
+
+/**
+  * @brief In the following line adjust the Internal High Speed oscillator (HSI) Startup
+  *        Timeout value
+  */
+#if !defined  (HSI_STARTUP_TIMEOUT)
+  #define HSI_STARTUP_TIMEOUT  5000U     /*!< Time out for HSI start up */
+#endif /* HSI_STARTUP_TIMEOUT */
+
+/**
+  * @brief Internal High Speed oscillator for ADC (HSI14) value.
+  */
+#if !defined  (HSI14_VALUE)
+  #define HSI14_VALUE          14000000U /*!< Value of the Internal High Speed oscillator for ADC in Hz.
+                                             The real value may vary depending on the variations
+                                             in voltage and temperature.  */
+#endif /* HSI14_VALUE */
+
+/**
+  * @brief Internal High Speed oscillator for USB (HSI48) value.
+  */
+#if !defined  (HSI48_VALUE)
+  #define HSI48_VALUE          48000000U /*!< Value of the Internal High Speed oscillator for USB in Hz.
+                                             The real value may vary depending on the variations
+                                             in voltage and temperature.  */
+#endif /* HSI48_VALUE */
+
+/**
+  * @brief Internal Low Speed oscillator (LSI) value.
+  */
+#if !defined  (LSI_VALUE)
+  #define LSI_VALUE            40000U
+#endif /* LSI_VALUE */                   /*!< Value of the Internal Low Speed oscillator in Hz
+                                             The real value may vary depending on the variations
+                                             in voltage and temperature.  */
+/**
+  * @brief External Low Speed oscillator (LSE) value.
+  */
+#if !defined  (LSE_VALUE)
+  #define LSE_VALUE            32768U    /*!< Value of the External Low Speed oscillator in Hz */
+#endif /* LSE_VALUE */
+
+/**
+  * @brief Time out for LSE start up value in ms.
+  */
+#if !defined  (LSE_STARTUP_TIMEOUT)
+  #define LSE_STARTUP_TIMEOUT  5000U     /*!< Time out for LSE start up, in ms */
+#endif /* LSE_STARTUP_TIMEOUT */
+
+
+/* Tip: To avoid modifying this file each time you need to use different HSE,
+   ===  you can define the HSE value in your toolchain compiler preprocessor. */
+
+/* ########################### System Configuration ######################### */
+/**
+  * @brief This is the HAL system configuration section
+  */
+#define  VDD_VALUE                    3300U  /*!< Value of VDD in mv */
+#define  TICK_INT_PRIORITY            ((uint32_t)(1U<<__NVIC_PRIO_BITS) - 1U) /*!< tick interrupt priority (lowest by default)             */
+                                                                              /*  Warning: Must be set to higher priority for HAL_Delay()  */
+                                                                              /*  and HAL_GetTick() usage under interrupt context          */
+#define  USE_RTOS                     0U
+#define  PREFETCH_ENABLE              1U
+#define  INSTRUCTION_CACHE_ENABLE     0U
+#define  DATA_CACHE_ENABLE            0U
+#define  USE_SPI_CRC                  1U
+
+/* ########################## Assert Selection ############################## */
+/**
+  * @brief Uncomment the line below to expanse the "assert_param" macro in the
+  *        HAL drivers code
+  */
+/*#define USE_FULL_ASSERT    1*/
+
+/* Includes ------------------------------------------------------------------*/
+/**
+  * @brief Include module's header file
+  */
+
+#ifdef HAL_RCC_MODULE_ENABLED
+ #include "stm32f0xx_hal_rcc.h"
+#endif /* HAL_RCC_MODULE_ENABLED */
+
+#ifdef HAL_GPIO_MODULE_ENABLED
+ #include "stm32f0xx_hal_gpio.h"
+#endif /* HAL_GPIO_MODULE_ENABLED */
+
+#ifdef HAL_DMA_MODULE_ENABLED
+  #include "stm32f0xx_hal_dma.h"
+#endif /* HAL_DMA_MODULE_ENABLED */
+
+#ifdef HAL_CORTEX_MODULE_ENABLED
+ #include "stm32f0xx_hal_cortex.h"
+#endif /* HAL_CORTEX_MODULE_ENABLED */
+
+#ifdef HAL_ADC_MODULE_ENABLED
+ #include "stm32f0xx_hal_adc.h"
+#endif /* HAL_ADC_MODULE_ENABLED */
+
+#ifdef HAL_CAN_MODULE_ENABLED
+ #include "stm32f0xx_hal_can.h"
+#endif /* HAL_CAN_MODULE_ENABLED */
+
+#ifdef HAL_CEC_MODULE_ENABLED
+ #include "stm32f0xx_hal_cec.h"
+#endif /* HAL_CEC_MODULE_ENABLED */
+
+#ifdef HAL_COMP_MODULE_ENABLED
+ #include "stm32f0xx_hal_comp.h"
+#endif /* HAL_COMP_MODULE_ENABLED */
+
+#ifdef HAL_CRC_MODULE_ENABLED
+ #include "stm32f0xx_hal_crc.h"
+#endif /* HAL_CRC_MODULE_ENABLED */
+
+#ifdef HAL_DAC_MODULE_ENABLED
+ #include "stm32f0xx_hal_dac.h"
+#endif /* HAL_DAC_MODULE_ENABLED */
+
+#ifdef HAL_FLASH_MODULE_ENABLED
+ #include "stm32f0xx_hal_flash.h"
+#endif /* HAL_FLASH_MODULE_ENABLED */
+
+#ifdef HAL_I2C_MODULE_ENABLED
+ #include "stm32f0xx_hal_i2c.h"
+#endif /* HAL_I2C_MODULE_ENABLED */
+
+#ifdef HAL_I2S_MODULE_ENABLED
+ #include "stm32f0xx_hal_i2s.h"
+#endif /* HAL_I2S_MODULE_ENABLED */
+
+#ifdef HAL_IRDA_MODULE_ENABLED
+ #include "stm32f0xx_hal_irda.h"
+#endif /* HAL_IRDA_MODULE_ENABLED */
+
+#ifdef HAL_IWDG_MODULE_ENABLED
+ #include "stm32f0xx_hal_iwdg.h"
+#endif /* HAL_IWDG_MODULE_ENABLED */
+
+#ifdef HAL_PCD_MODULE_ENABLED
+ #include "stm32f0xx_hal_pcd.h"
+#endif /* HAL_PCD_MODULE_ENABLED */
+
+#ifdef HAL_PWR_MODULE_ENABLED
+ #include "stm32f0xx_hal_pwr.h"
+#endif /* HAL_PWR_MODULE_ENABLED */
+
+#ifdef HAL_RTC_MODULE_ENABLED
+ #include "stm32f0xx_hal_rtc.h"
+#endif /* HAL_RTC_MODULE_ENABLED */
+
+#ifdef HAL_SMARTCARD_MODULE_ENABLED
+ #include "stm32f0xx_hal_smartcard.h"
+#endif /* HAL_SMARTCARD_MODULE_ENABLED */
+
+#ifdef HAL_SMBUS_MODULE_ENABLED
+ #include "stm32f0xx_hal_smbus.h"
+#endif /* HAL_SMBUS_MODULE_ENABLED */
+
+#ifdef HAL_SPI_MODULE_ENABLED
+ #include "stm32f0xx_hal_spi.h"
+#endif /* HAL_SPI_MODULE_ENABLED */
+
+#ifdef HAL_TIM_MODULE_ENABLED
+ #include "stm32f0xx_hal_tim.h"
+#endif /* HAL_TIM_MODULE_ENABLED */
+
+#ifdef HAL_TSC_MODULE_ENABLED
+ #include "stm32f0xx_hal_tsc.h"
+#endif /* HAL_TSC_MODULE_ENABLED */
+
+#ifdef HAL_UART_MODULE_ENABLED
+ #include "stm32f0xx_hal_uart.h"
+#endif /* HAL_UART_MODULE_ENABLED */
+
+#ifdef HAL_USART_MODULE_ENABLED
+ #include "stm32f0xx_hal_usart.h"
+#endif /* HAL_USART_MODULE_ENABLED */
+
+#ifdef HAL_WWDG_MODULE_ENABLED
+ #include "stm32f0xx_hal_wwdg.h"
+#endif /* HAL_WWDG_MODULE_ENABLED */
+
+/* Exported macro ------------------------------------------------------------*/
+#ifdef  USE_FULL_ASSERT
+/**
+  * @brief  The assert_param macro is used for function's parameters check.
+  * @param  expr: If expr is false, it calls assert_failed function
+  *         which reports the name of the source file and the source
+  *         line number of the call that failed.
+  *         If expr is true, it returns no value.
+  * @retval None
+  */
+  #define assert_param(expr) ((expr) ? (void)0U : assert_failed((char *)__FILE__, __LINE__))
+/* Exported functions ------------------------------------------------------- */
+  void assert_failed(char* file, uint32_t line);
+#else
+  #define assert_param(expr) ((void)0U)
+#endif /* USE_FULL_ASSERT */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F0xx_HAL_CONF_H */
+
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/