diff --git a/ports/stm32/boards/STM32L496GDISC/mpconfigboard.h b/ports/stm32/boards/STM32L496GDISC/mpconfigboard.h
new file mode 100644
index 0000000000..6a17d74d3a
--- /dev/null
+++ b/ports/stm32/boards/STM32L496GDISC/mpconfigboard.h
@@ -0,0 +1,52 @@
+#define MICROPY_HW_BOARD_NAME "L496G-DISCO"
+#define MICROPY_HW_MCU_NAME "STM32L496"
+
+#define MICROPY_HW_HAS_SWITCH (1)
+#define MICROPY_HW_ENABLE_RNG (1)
+#define MICROPY_HW_ENABLE_RTC (1)
+#define MICROPY_HW_ENABLE_TIMER (1)
+#define MICROPY_HW_ENABLE_USB (1)
+
+// MSI is used and is 4MHz,
+// Resulting core frequency is 80MHz:
+#define MICROPY_HW_CLK_PLLM (1)
+#define MICROPY_HW_CLK_PLLN (40)
+#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV7)
+#define MICROPY_HW_CLK_PLLR (RCC_PLLR_DIV2)
+#define MICROPY_HW_CLK_PLLQ (RCC_PLLQ_DIV2)
+
+#define MICROPY_HW_FLASH_LATENCY FLASH_LATENCY_4
+
+// USART config
+#define MICROPY_HW_UART2_TX (pin_A2)
+#define MICROPY_HW_UART2_RX (pin_D6)
+// USART 2 is connected to the virtual com port on the ST-LINK
+#define MICROPY_HW_UART_REPL PYB_UART_2
+#define MICROPY_HW_UART_REPL_BAUD 115200
+
+// I2C busses
+#define MICROPY_HW_I2C1_SCL (pin_G14)
+#define MICROPY_HW_I2C1_SDA (pin_G13)
+#define MICROPY_HW_I2C2_SCL (pin_H4)
+#define MICROPY_HW_I2C2_SDA (pin_B14)
+
+// SPI busses
+// -> To the arduino connector
+#define MICROPY_HW_SPI1_NSS (pin_A15)
+#define MICROPY_HW_SPI1_SCK (pin_A5)
+#define MICROPY_HW_SPI1_MISO (pin_B4)
+#define MICROPY_HW_SPI1_MOSI (pin_B5)
+
+// Use Sel from joystick. Joystick is pulled low. Pressing the button makes the input go high.
+#define MICROPY_HW_USRSW_PIN (pin_C13)
+#define MICROPY_HW_USRSW_PULL (GPIO_PULLDOWN)
+#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING)
+#define MICROPY_HW_USRSW_PRESSED (1)
+
+// LED (The orange LED is controlled over MFX)
+#define MICROPY_HW_LED1 (pin_B13) // Green
+#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_low(pin))
+#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_high(pin))
+// USB config
+#define MICROPY_HW_USB_FS (1)
+#define MICROPY_HW_USB_OTG_ID_PIN (pin_A10)
diff --git a/ports/stm32/boards/STM32L496GDISC/mpconfigboard.mk b/ports/stm32/boards/STM32L496GDISC/mpconfigboard.mk
new file mode 100644
index 0000000000..3a61746556
--- /dev/null
+++ b/ports/stm32/boards/STM32L496GDISC/mpconfigboard.mk
@@ -0,0 +1,7 @@
+MCU_SERIES = l4
+CMSIS_MCU = STM32L496xx
+AF_FILE = boards/stm32l496_af.csv
+LD_FILES = boards/stm32l496xg.ld boards/common_ifs.ld
+TEXT0_ADDR = 0x08000000
+TEXT1_ADDR = 0x08004000
+OPENOCD_CONFIG = boards/openocd_stm32l4.cfg
diff --git a/ports/stm32/boards/STM32L496GDISC/pins.csv b/ports/stm32/boards/STM32L496GDISC/pins.csv
new file mode 100644
index 0000000000..2ee054032b
--- /dev/null
+++ b/ports/stm32/boards/STM32L496GDISC/pins.csv
@@ -0,0 +1,140 @@
+PA0,PA0
+PA1,PA1
+PA2,PA2
+PA3,PA3
+PA4,PA4
+PA5,PA5
+PA6,PA6
+PA7,PA7
+PA8,PA8
+PA9,PA9
+PA10,PA10
+PA11,PA11
+PA12,PA12
+PA13,PA13
+PA14,PA14
+PA15,PA15
+PB0,PB0
+PB1,PB1
+PB2,PB2
+PB3,PB3
+PB4,PB4
+PB5,PB5
+PB6,PB6
+PB7,PB7
+PB8,PB8
+PB9,PB9
+PB10,PB10
+PB11,PB11
+PB12,PB12
+PB13,PB13
+PB14,PB14
+PB15,PB15
+PC0,PC0
+PC1,PC1
+PC2,PC2
+PC3,PC3
+PC4,PC4
+PC5,PC5
+PC6,PC6
+PC7,PC7
+PC8,PC8
+PC9,PC9
+PC10,PC10
+PC11,PC11
+PC12,PC12
+PC13,PC13
+PC14,PC14
+PC15,PC15
+PD0,PD0
+PD1,PD1
+PD2,PD2
+PD3,PD3
+PD4,PD4
+PD5,PD5
+PD6,PD6
+PD7,PD7
+PD8,PD8
+PD9,PD9
+PD10,PD10
+PD11,PD11
+PD12,PD12
+PD13,PD13
+PD14,PD14
+PD15,PD15
+PE0,PE0
+PE1,PE1
+PE2,PE2
+PE3,PE3
+PE4,PE4
+PE5,PE5
+PE6,PE6
+PE7,PE7
+PE8,PE8
+PE9,PE9
+PE10,PE10
+PE11,PE11
+PE12,PE12
+PE13,PE13
+PE14,PE14
+PE15,PE15
+PF0,PF0
+PF1,PF1
+PF2,PF2
+PF3,PF3
+PF4,PF4
+PF5,PF5
+PF6,PF6
+PF7,PF7
+PF8,PF8
+PF9,PF9
+PF10,PF10
+PF11,PF11
+PF12,PF12
+PF13,PF13
+PF14,PF14
+PF15,PF15
+PG0,PG0
+PG1,PG1
+PG2,PG2
+PG3,PG3
+PG4,PG4
+PG5,PG5
+PG6,PG6
+PG7,PG7
+PG8,PG8
+PG9,PG9
+PG10,PG10
+PG11,PG11
+PG12,PG12
+PG13,PG13
+PG14,PG14
+PG15,PG15
+PH0,PH0
+PH1,PH1
+PH2,PH2
+PH3,PH3
+PH4,PH4
+PH5,PH5
+PH6,PH6
+PH7,PH7
+PH8,PH8
+PH9,PH9
+PH10,PH10
+PH11,PH11
+PH12,PH12
+PH13,PH13
+PH14,PH14
+PH15,PH15
+PI0,PI0
+PI1,PI1
+PI2,PI2
+PI3,PI3
+PI4,PI4
+PI5,PI5
+PI6,PI6
+PI7,PI7
+PI8,PI8
+PI9,PI9
+PI10,PI10
+PI11,PI11
diff --git a/ports/stm32/boards/STM32L496GDISC/stm32l4xx_hal_conf.h b/ports/stm32/boards/STM32L496GDISC/stm32l4xx_hal_conf.h
new file mode 100644
index 0000000000..884db5ef1a
--- /dev/null
+++ b/ports/stm32/boards/STM32L496GDISC/stm32l4xx_hal_conf.h
@@ -0,0 +1,421 @@
+/**
+ ******************************************************************************
+ * @file stm32l4xx_hal_conf.h
+ * @brief HAL configuration file.
+ ******************************************************************************
+ * @attention
+ *
+ *
© COPYRIGHT(c) 2018 STMicroelectronics
+ *
+ * Redistribution and use in source and binary forms, with or without modification,
+ * are permitted provided that the following conditions are met:
+ * 1. Redistributions of source code must retain the above copyright notice,
+ * this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ * this list of conditions and the following disclaimer in the documentation
+ * and/or other materials provided with the distribution.
+ * 3. Neither the name of STMicroelectronics nor the names of its contributors
+ * may be used to endorse or promote products derived from this software
+ * without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ ******************************************************************************
+ */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32L4xx_HAL_CONF_H
+#define __STM32L4xx_HAL_CONF_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Exported types ------------------------------------------------------------*/
+/* Exported constants --------------------------------------------------------*/
+
+/* ########################## Module Selection ############################## */
+/**
+ * @brief This is the list of modules to be used in the HAL driver
+ */
+
+#define HAL_MODULE_ENABLED
+#define HAL_ADC_MODULE_ENABLED
+/*#define HAL_CRYP_MODULE_ENABLED */
+#define HAL_CAN_MODULE_ENABLED
+/* #define HAL_COMP_MODULE_ENABLED */
+/* #define HAL_CRC_MODULE_ENABLED */
+/* #define HAL_CRYP_MODULE_ENABLED */
+#define HAL_DAC_MODULE_ENABLED
+/* #define HAL_DCMI_MODULE_ENABLED */
+/*#define HAL_DMA2D_MODULE_ENABLED */
+/* #define HAL_DFSDM_MODULE_ENABLED */
+/*#define HAL_DSI_MODULE_ENABLED */
+/*#define HAL_FIREWALL_MODULE_ENABLED */
+/*#define HAL_GFXMMU_MODULE_ENABLED */
+/*#define HAL_HCD_MODULE_ENABLED */
+/*#define HAL_HASH_MODULE_ENABLED */
+/*#define HAL_I2S_MODULE_ENABLED */
+/*#define HAL_IRDA_MODULE_ENABLED */
+/*#define HAL_IWDG_MODULE_ENABLED */
+/*#define HAL_LTDC_MODULE_ENABLED */
+/*#define HAL_LCD_MODULE_ENABLED */
+/*#define HAL_LPTIM_MODULE_ENABLED */
+/*#define HAL_NAND_MODULE_ENABLED */
+/*#define HAL_NOR_MODULE_ENABLED */
+/*#define HAL_OPAMP_MODULE_ENABLED */
+/*#define HAL_OSPI_MODULE_ENABLED */
+#define HAL_PCD_MODULE_ENABLED
+#define HAL_RNG_MODULE_ENABLED
+#define HAL_RTC_MODULE_ENABLED
+/* #define HAL_SAI_MODULE_ENABLED */
+#define HAL_SD_MODULE_ENABLED
+/* #define HAL_SMBUS_MODULE_ENABLED */
+/* #define HAL_SMARTCARD_MODULE_ENABLED */
+#define HAL_SPI_MODULE_ENABLED
+/*#define HAL_SRAM_MODULE_ENABLED */
+/*#define HAL_SWPMI_MODULE_ENABLED */
+#define HAL_TIM_MODULE_ENABLED
+/*#define HAL_TSC_MODULE_ENABLED */
+#define HAL_UART_MODULE_ENABLED
+/*#define HAL_USART_MODULE_ENABLED */
+/*#define HAL_WWDG_MODULE_ENABLED */
+#define HAL_GPIO_MODULE_ENABLED
+#define HAL_I2C_MODULE_ENABLED
+#define HAL_DMA_MODULE_ENABLED
+#define HAL_RCC_MODULE_ENABLED
+#define HAL_FLASH_MODULE_ENABLED
+#define HAL_PWR_MODULE_ENABLED
+#define HAL_CORTEX_MODULE_ENABLED
+
+/* ########################## Oscillator Values adaptation ####################*/
+/**
+ * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
+ * This value is used by the RCC HAL module to compute the system frequency
+ * (when HSE is used as system clock source, directly or through the PLL).
+ */
+#if !defined (HSE_VALUE)
+ #define HSE_VALUE ((uint32_t)8000000) /*!< Value of the External oscillator in Hz */
+#endif /* HSE_VALUE */
+
+#if !defined (HSE_STARTUP_TIMEOUT)
+ #define HSE_STARTUP_TIMEOUT ((uint32_t)100) /*!< Time out for HSE start up, in ms */
+#endif /* HSE_STARTUP_TIMEOUT */
+
+/**
+ * @brief Internal Multiple Speed oscillator (MSI) default value.
+ * This value is the default MSI range value after Reset.
+ */
+#if !defined (MSI_VALUE)
+ #define MSI_VALUE ((uint32_t)4000000) /*!< Value of the Internal oscillator in Hz*/
+#endif /* MSI_VALUE */
+/**
+ * @brief Internal High Speed oscillator (HSI) value.
+ * This value is used by the RCC HAL module to compute the system frequency
+ * (when HSI is used as system clock source, directly or through the PLL).
+ */
+#if !defined (HSI_VALUE)
+ #define HSI_VALUE ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/
+#endif /* HSI_VALUE */
+
+ /**
+ * @brief Internal High Speed oscillator (HSI48) value for USB FS, SDMMC and RNG.
+ * This internal oscillator is mainly dedicated to provide a high precision clock to
+ * the USB peripheral by means of a special Clock Recovery System (CRS) circuitry.
+ * When the CRS is not used, the HSI48 RC oscillator runs on it default frequency
+ * which is subject to manufacturing process variations.
+ */
+ #if !defined (HSI48_VALUE)
+ #define HSI48_VALUE ((uint32_t)48000000U) /*!< Value of the Internal High Speed oscillator for USB FS/SDMMC/RNG in Hz.
+ The real value my vary depending on manufacturing process variations.*/
+ #endif /* HSI48_VALUE */
+
+/**
+ * @brief Internal Low Speed oscillator (LSI) value.
+ */
+#if !defined (LSI_VALUE)
+ #define LSI_VALUE ((uint32_t)32000) /*!< LSI Typical Value in Hz*/
+#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz
+ The real value may vary depending on the variations
+ in voltage and temperature. */
+/**
+ * @brief External Low Speed oscillator (LSE) value.
+ * This value is used by the UART, RTC HAL module to compute the system frequency
+ */
+#if !defined (LSE_VALUE)
+ #define LSE_VALUE ((uint32_t)32768) /*!< Value of the External oscillator in Hz*/
+#endif /* LSE_VALUE */
+
+#if !defined (LSE_STARTUP_TIMEOUT)
+ #define LSE_STARTUP_TIMEOUT ((uint32_t)5000) /*!< Time out for LSE start up, in ms */
+#endif /* HSE_STARTUP_TIMEOUT */
+
+/**
+ * @brief External clock source for SAI1 peripheral
+ * This value is used by the RCC HAL module to compute the SAI1 & SAI2 clock source
+ * frequency.
+ */
+#if !defined (EXTERNAL_SAI1_CLOCK_VALUE)
+ #define EXTERNAL_SAI1_CLOCK_VALUE ((uint32_t)48000) /*!< Value of the SAI1 External clock source in Hz*/
+#endif /* EXTERNAL_SAI1_CLOCK_VALUE */
+
+/**
+ * @brief External clock source for SAI2 peripheral
+ * This value is used by the RCC HAL module to compute the SAI1 & SAI2 clock source
+ * frequency.
+ */
+#if !defined (EXTERNAL_SAI2_CLOCK_VALUE)
+ #define EXTERNAL_SAI2_CLOCK_VALUE ((uint32_t)48000) /*!< Value of the SAI2 External clock source in Hz*/
+#endif /* EXTERNAL_SAI2_CLOCK_VALUE */
+
+/* Tip: To avoid modifying this file each time you need to use different HSE,
+ === you can define the HSE value in your toolchain compiler preprocessor. */
+
+/* ########################### System Configuration ######################### */
+/**
+ * @brief This is the HAL system configuration section
+ */
+#define VDD_VALUE ((uint32_t)3300) /*!< Value of VDD in mv */
+#define TICK_INT_PRIORITY ((uint32_t)0x00) /*!< tick interrupt priority */
+#define USE_RTOS 0
+#define PREFETCH_ENABLE 1
+#define INSTRUCTION_CACHE_ENABLE 1
+#define DATA_CACHE_ENABLE 1
+
+/* ########################## Assert Selection ############################## */
+/**
+ * @brief Uncomment the line below to expanse the "assert_param" macro in the
+ * HAL drivers code
+ */
+/* #define USE_FULL_ASSERT 1 */
+
+/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver
+ * Activated: CRC code is present inside driver
+ * Deactivated: CRC code cleaned from driver
+ */
+
+#define USE_SPI_CRC 0
+
+/* Includes ------------------------------------------------------------------*/
+/**
+ * @brief Include module's header file
+ */
+
+#ifdef HAL_RCC_MODULE_ENABLED
+ #include "stm32l4xx_hal_rcc.h"
+ #include "stm32l4xx_hal_rcc_ex.h"
+#endif /* HAL_RCC_MODULE_ENABLED */
+
+#ifdef HAL_GPIO_MODULE_ENABLED
+ #include "stm32l4xx_hal_gpio.h"
+#endif /* HAL_GPIO_MODULE_ENABLED */
+
+#ifdef HAL_DMA_MODULE_ENABLED
+ #include "stm32l4xx_hal_dma.h"
+#endif /* HAL_DMA_MODULE_ENABLED */
+
+#ifdef HAL_DFSDM_MODULE_ENABLED
+ #include "stm32l4xx_hal_dfsdm.h"
+#endif /* HAL_DFSDM_MODULE_ENABLED */
+
+#ifdef HAL_CORTEX_MODULE_ENABLED
+ #include "stm32l4xx_hal_cortex.h"
+#endif /* HAL_CORTEX_MODULE_ENABLED */
+
+#ifdef HAL_ADC_MODULE_ENABLED
+ #include "stm32l4xx_hal_adc.h"
+#endif /* HAL_ADC_MODULE_ENABLED */
+
+#ifdef HAL_CAN_MODULE_ENABLED
+ #include "stm32l4xx_hal_can.h"
+#endif /* HAL_CAN_MODULE_ENABLED */
+
+#ifdef HAL_COMP_MODULE_ENABLED
+ #include "stm32l4xx_hal_comp.h"
+#endif /* HAL_COMP_MODULE_ENABLED */
+
+#ifdef HAL_CRC_MODULE_ENABLED
+ #include "stm32l4xx_hal_crc.h"
+#endif /* HAL_CRC_MODULE_ENABLED */
+
+#ifdef HAL_CRYP_MODULE_ENABLED
+ #include "stm32l4xx_hal_cryp.h"
+#endif /* HAL_CRYP_MODULE_ENABLED */
+
+#ifdef HAL_DAC_MODULE_ENABLED
+ #include "stm32l4xx_hal_dac.h"
+#endif /* HAL_DAC_MODULE_ENABLED */
+
+#ifdef HAL_DCMI_MODULE_ENABLED
+ #include "stm32l4xx_hal_dcmi.h"
+#endif /* HAL_DCMI_MODULE_ENABLED */
+
+#ifdef HAL_DMA2D_MODULE_ENABLED
+ #include "stm32l4xx_hal_dma2d.h"
+#endif /* HAL_DMA2D_MODULE_ENABLED */
+
+#ifdef HAL_DSI_MODULE_ENABLED
+ #include "stm32l4xx_hal_dsi.h"
+#endif /* HAL_DSI_MODULE_ENABLED */
+
+#ifdef HAL_FIREWALL_MODULE_ENABLED
+ #include "stm32l4xx_hal_firewall.h"
+#endif /* HAL_FIREWALL_MODULE_ENABLED */
+
+#ifdef HAL_FLASH_MODULE_ENABLED
+ #include "stm32l4xx_hal_flash.h"
+#endif /* HAL_FLASH_MODULE_ENABLED */
+
+#ifdef HAL_HASH_MODULE_ENABLED
+ #include "stm32l4xx_hal_hash.h"
+#endif /* HAL_HASH_MODULE_ENABLED */
+
+#ifdef HAL_SRAM_MODULE_ENABLED
+ #include "stm32l4xx_hal_sram.h"
+#endif /* HAL_SRAM_MODULE_ENABLED */
+
+#ifdef HAL_NOR_MODULE_ENABLED
+ #include "stm32l4xx_hal_nor.h"
+#endif /* HAL_NOR_MODULE_ENABLED */
+
+#ifdef HAL_NAND_MODULE_ENABLED
+ #include "stm32l4xx_hal_nand.h"
+#endif /* HAL_NAND_MODULE_ENABLED */
+
+#ifdef HAL_I2C_MODULE_ENABLED
+ #include "stm32l4xx_hal_i2c.h"
+#endif /* HAL_I2C_MODULE_ENABLED */
+
+#ifdef HAL_IWDG_MODULE_ENABLED
+ #include "stm32l4xx_hal_iwdg.h"
+#endif /* HAL_IWDG_MODULE_ENABLED */
+
+#ifdef HAL_LCD_MODULE_ENABLED
+ #include "stm32l4xx_hal_lcd.h"
+#endif /* HAL_LCD_MODULE_ENABLED */
+
+#ifdef HAL_LPTIM_MODULE_ENABLED
+ #include "stm32l4xx_hal_lptim.h"
+#endif /* HAL_LPTIM_MODULE_ENABLED */
+
+#ifdef HAL_LTDC_MODULE_ENABLED
+ #include "stm32l4xx_hal_ltdc.h"
+#endif /* HAL_LTDC_MODULE_ENABLED */
+
+#ifdef HAL_OPAMP_MODULE_ENABLED
+ #include "stm32l4xx_hal_opamp.h"
+#endif /* HAL_OPAMP_MODULE_ENABLED */
+
+#ifdef HAL_OSPI_MODULE_ENABLED
+ #include "stm32l4xx_hal_ospi.h"
+#endif /* HAL_OSPI_MODULE_ENABLED */
+
+#ifdef HAL_PWR_MODULE_ENABLED
+ #include "stm32l4xx_hal_pwr.h"
+#endif /* HAL_PWR_MODULE_ENABLED */
+
+#ifdef HAL_QSPI_MODULE_ENABLED
+ #include "stm32l4xx_hal_qspi.h"
+#endif /* HAL_QSPI_MODULE_ENABLED */
+
+#ifdef HAL_RNG_MODULE_ENABLED
+ #include "stm32l4xx_hal_rng.h"
+#endif /* HAL_RNG_MODULE_ENABLED */
+
+#ifdef HAL_RTC_MODULE_ENABLED
+ #include "stm32l4xx_hal_rtc.h"
+#endif /* HAL_RTC_MODULE_ENABLED */
+
+#ifdef HAL_SAI_MODULE_ENABLED
+ #include "stm32l4xx_hal_sai.h"
+#endif /* HAL_SAI_MODULE_ENABLED */
+
+#ifdef HAL_SD_MODULE_ENABLED
+ #include "stm32l4xx_hal_sd.h"
+#endif /* HAL_SD_MODULE_ENABLED */
+
+#ifdef HAL_SMBUS_MODULE_ENABLED
+ #include "stm32l4xx_hal_smbus.h"
+#endif /* HAL_SMBUS_MODULE_ENABLED */
+
+#ifdef HAL_SPI_MODULE_ENABLED
+ #include "stm32l4xx_hal_spi.h"
+#endif /* HAL_SPI_MODULE_ENABLED */
+
+#ifdef HAL_SWPMI_MODULE_ENABLED
+ #include "stm32l4xx_hal_swpmi.h"
+#endif /* HAL_SWPMI_MODULE_ENABLED */
+
+#ifdef HAL_TIM_MODULE_ENABLED
+ #include "stm32l4xx_hal_tim.h"
+#endif /* HAL_TIM_MODULE_ENABLED */
+
+#ifdef HAL_TSC_MODULE_ENABLED
+ #include "stm32l4xx_hal_tsc.h"
+#endif /* HAL_TSC_MODULE_ENABLED */
+
+#ifdef HAL_UART_MODULE_ENABLED
+ #include "stm32l4xx_hal_uart.h"
+#endif /* HAL_UART_MODULE_ENABLED */
+
+#ifdef HAL_USART_MODULE_ENABLED
+ #include "stm32l4xx_hal_usart.h"
+#endif /* HAL_USART_MODULE_ENABLED */
+
+#ifdef HAL_IRDA_MODULE_ENABLED
+ #include "stm32l4xx_hal_irda.h"
+#endif /* HAL_IRDA_MODULE_ENABLED */
+
+#ifdef HAL_SMARTCARD_MODULE_ENABLED
+ #include "stm32l4xx_hal_smartcard.h"
+#endif /* HAL_SMARTCARD_MODULE_ENABLED */
+
+#ifdef HAL_WWDG_MODULE_ENABLED
+ #include "stm32l4xx_hal_wwdg.h"
+#endif /* HAL_WWDG_MODULE_ENABLED */
+
+#ifdef HAL_PCD_MODULE_ENABLED
+ #include "stm32l4xx_hal_pcd.h"
+#endif /* HAL_PCD_MODULE_ENABLED */
+
+#ifdef HAL_HCD_MODULE_ENABLED
+ #include "stm32l4xx_hal_hcd.h"
+#endif /* HAL_HCD_MODULE_ENABLED */
+
+#ifdef HAL_GFXMMU_MODULE_ENABLED
+ #include "stm32l4xx_hal_gfxmmu.h"
+#endif /* HAL_GFXMMU_MODULE_ENABLED */
+
+/* Exported macro ------------------------------------------------------------*/
+#ifdef USE_FULL_ASSERT
+/**
+ * @brief The assert_param macro is used for function's parameters check.
+ * @param expr: If expr is false, it calls assert_failed function
+ * which reports the name of the source file and the source
+ * line number of the call that failed.
+ * If expr is true, it returns no value.
+ * @retval None
+ */
+ #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__))
+/* Exported functions ------------------------------------------------------- */
+ void assert_failed(uint8_t* file, uint32_t line);
+#else
+ #define assert_param(expr) ((void)0U)
+#endif /* USE_FULL_ASSERT */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32L4xx_HAL_CONF_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/