kopia lustrzana https://github.com/micropython/micropython
79 wiersze
2.9 KiB
C
79 wiersze
2.9 KiB
C
![]() |
#define MICROPY_HW_BOARD_NAME "F4DISC"
|
||
![]() |
#define MICROPY_HW_MCU_NAME "STM32F407"
|
||
![]() |
|
||
|
#define MICROPY_HW_HAS_SWITCH (1)
|
||
![]() |
#define MICROPY_HW_HAS_FLASH (1)
|
||
![]() |
#define MICROPY_HW_ENABLE_RNG (1)
|
||
|
#define MICROPY_HW_ENABLE_RTC (1)
|
||
![]() |
#define MICROPY_HW_ENABLE_DAC (1)
|
||
![]() |
#define MICROPY_HW_ENABLE_CAN (1)
|
||
![]() |
|
||
![]() |
// HSE is 8MHz
|
||
|
#define MICROPY_HW_CLK_PLLM (8)
|
||
|
#define MICROPY_HW_CLK_PLLN (336)
|
||
|
#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2)
|
||
|
#define MICROPY_HW_CLK_PLLQ (7)
|
||
|
|
||
![]() |
// UART config
|
||
![]() |
#if 0
|
||
|
// A9 is used for USB VBUS detect, and A10 is used for USB_FS_ID.
|
||
|
// UART1 is also on PB6/7 but PB6 is tied to the Audio SCL line.
|
||
|
// Without board modifications, this makes UART1 unusable on this board.
|
||
![]() |
#define MICROPY_HW_UART1_TX (pin_A9)
|
||
|
#define MICROPY_HW_UART1_RX (pin_A10)
|
||
![]() |
#endif
|
||
![]() |
#define MICROPY_HW_UART2_TX (pin_A2)
|
||
|
#define MICROPY_HW_UART2_RX (pin_A3)
|
||
|
#define MICROPY_HW_UART2_RTS (pin_A1)
|
||
|
#define MICROPY_HW_UART2_CTS (pin_A0)
|
||
|
#define MICROPY_HW_UART3_TX (pin_D8)
|
||
|
#define MICROPY_HW_UART3_RX (pin_D9)
|
||
|
#define MICROPY_HW_UART3_RTS (pin_D12)
|
||
|
#define MICROPY_HW_UART3_CTS (pin_D11)
|
||
![]() |
#if MICROPY_HW_HAS_SWITCH == 0
|
||
|
// NOTE: A0 also connects to the user switch. To use UART4 you should
|
||
|
// set MICROPY_HW_HAS_SWITCH to 0, and also remove SB20 (on the back
|
||
|
// of the board near the USER switch).
|
||
![]() |
#define MICROPY_HW_UART4_TX (pin_A0)
|
||
|
#define MICROPY_HW_UART4_RX (pin_A1)
|
||
![]() |
#endif
|
||
|
// NOTE: PC7 is connected to MCLK on the Audio chip. This is an input signal
|
||
|
// so I think as long as you're not using the audio chip then it should
|
||
|
// be fine to use as a UART pin.
|
||
![]() |
#define MICROPY_HW_UART6_TX (pin_C6)
|
||
|
#define MICROPY_HW_UART6_RX (pin_C7)
|
||
![]() |
|
||
![]() |
// I2C busses
|
||
|
#define MICROPY_HW_I2C1_SCL (pin_B6)
|
||
|
#define MICROPY_HW_I2C1_SDA (pin_B7)
|
||
|
#define MICROPY_HW_I2C2_SCL (pin_B10)
|
||
|
#define MICROPY_HW_I2C2_SDA (pin_B11)
|
||
|
|
||
![]() |
// SPI busses
|
||
|
#define MICROPY_HW_SPI1_NSS (pin_A4)
|
||
|
#define MICROPY_HW_SPI1_SCK (pin_A5)
|
||
|
#define MICROPY_HW_SPI1_MISO (pin_A6)
|
||
|
#define MICROPY_HW_SPI1_MOSI (pin_A7)
|
||
|
#define MICROPY_HW_SPI2_NSS (pin_B12)
|
||
|
#define MICROPY_HW_SPI2_SCK (pin_B13)
|
||
|
#define MICROPY_HW_SPI2_MISO (pin_B14)
|
||
|
#define MICROPY_HW_SPI2_MOSI (pin_B15)
|
||
|
|
||
![]() |
// USRSW is pulled low. Pressing the button makes the input go high.
|
||
![]() |
#define MICROPY_HW_USRSW_PIN (pin_A0)
|
||
|
#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL)
|
||
|
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING)
|
||
|
#define MICROPY_HW_USRSW_PRESSED (1)
|
||
![]() |
|
||
![]() |
// LEDs
|
||
|
#define MICROPY_HW_LED1 (pin_D14) // red
|
||
|
#define MICROPY_HW_LED2 (pin_D12) // green
|
||
|
#define MICROPY_HW_LED3 (pin_D13) // orange
|
||
|
#define MICROPY_HW_LED4 (pin_D15) // blue
|
||
![]() |
#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin))
|
||
|
#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin))
|
||
![]() |
|
||
![]() |
// USB config
|
||
![]() |
#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_A9)
|
||
![]() |
#define MICROPY_HW_USB_OTG_ID_PIN (pin_A10)
|