micropython/ports/stm32/boards/CERB40/mpconfigboard.h

#define MICROPY_HW_BOARD_NAME       "Cerb40"
#define MICROPY_HW_MCU_NAME         "STM32F405RG"

#define MICROPY_HW_HAS_FLASH        (1)
#define MICROPY_HW_ENABLE_RNG       (1)
#define MICROPY_HW_ENABLE_RTC       (1)
#define MICROPY_HW_ENABLE_DAC       (1)
#define MICROPY_HW_ENABLE_USB       (1)

// HSE is 12MHz
#define MICROPY_HW_CLK_PLLM (12)
#define MICROPY_HW_CLK_PLLN (336)
#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2)
#define MICROPY_HW_CLK_PLLQ (7)

// UART config
#define MICROPY_HW_UART1_TX     (pin_A9)
#define MICROPY_HW_UART1_RX     (pin_A10)
#define MICROPY_HW_UART2_TX     (pin_A2)
#define MICROPY_HW_UART2_RX     (pin_A3)
#define MICROPY_HW_UART2_RTS    (pin_A1)
#define MICROPY_HW_UART2_CTS    (pin_A0)
#define MICROPY_HW_UART3_TX     (pin_D8)
#define MICROPY_HW_UART3_RX     (pin_D9)
#define MICROPY_HW_UART3_RTS    (pin_D12)
#define MICROPY_HW_UART3_CTS    (pin_D11)
#define MICROPY_HW_UART4_TX     (pin_A0)
#define MICROPY_HW_UART4_RX     (pin_A1)
#define MICROPY_HW_UART5_TX     (pin_C12)
#define MICROPY_HW_UART5_RX     (pin_D2)
#define MICROPY_HW_UART6_TX     (pin_C6)
#define MICROPY_HW_UART6_RX     (pin_C7)

// I2C buses
#define MICROPY_HW_I2C1_SCL (pin_B6)
#define MICROPY_HW_I2C1_SDA (pin_B7)
#define MICROPY_HW_I2C2_SCL (pin_B10)
#define MICROPY_HW_I2C2_SDA (pin_B11)
#define MICROPY_HW_I2C3_SCL (pin_A8)
#define MICROPY_HW_I2C3_SDA (pin_C9)

// SPI buses
#define MICROPY_HW_SPI1_NSS  (pin_A4)
#define MICROPY_HW_SPI1_SCK  (pin_A5)
#define MICROPY_HW_SPI1_MISO (pin_A6)
#define MICROPY_HW_SPI1_MOSI (pin_A7)
#define MICROPY_HW_SPI3_NSS  (pin_A4)
#define MICROPY_HW_SPI3_SCK  (pin_B3)
#define MICROPY_HW_SPI3_MISO (pin_B4)
#define MICROPY_HW_SPI3_MOSI (pin_B5)

// CAN buses
#define MICROPY_HW_CAN1_TX (pin_B9)
#define MICROPY_HW_CAN1_RX (pin_B8)
#define MICROPY_HW_CAN2_TX (pin_B13)
#define MICROPY_HW_CAN2_RX (pin_B12)

// The Cerb40 has No LEDs

// The Cerb40 has No SDCard

// USB config
#define MICROPY_HW_USB_FS (1)
//#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_A9)
//#define MICROPY_HW_USB_OTG_ID_PIN      (pin_A10)
stmhal: Add support for FEZ Cerb40 II board from ghielectronics.com. 2015-01-16 05:45:21 +00:00			`#define MICROPY_HW_BOARD_NAME "Cerb40"`
			`#define MICROPY_HW_MCU_NAME "STM32F405RG"`

stmhal/diskio: Introduce MICROPY_HW_HAS_FLASH setting. To allow to reuse stmhal/diskio for ports which don't have flash but have other storage devices. 2016-02-06 12:48:58 +00:00			`#define MICROPY_HW_HAS_FLASH (1)`
stmhal: Add support for FEZ Cerb40 II board from ghielectronics.com. 2015-01-16 05:45:21 +00:00			`#define MICROPY_HW_ENABLE_RNG (1)`
			`#define MICROPY_HW_ENABLE_RTC (1)`
			`#define MICROPY_HW_ENABLE_DAC (1)`
stm32/boards: Update all boards to work with new USB configuration. 2018-02-13 07:57:01 +00:00			`#define MICROPY_HW_ENABLE_USB (1)`
stmhal: Add support for FEZ Cerb40 II board from ghielectronics.com. 2015-01-16 05:45:21 +00:00
stmhal: Make HSE PLL parameters configurable per board. 2015-04-18 14:30:04 +00:00			`// HSE is 12MHz`
			`#define MICROPY_HW_CLK_PLLM (12)`
			`#define MICROPY_HW_CLK_PLLN (336)`
			`#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2)`
			`#define MICROPY_HW_CLK_PLLQ (7)`

stmhal: Allow to configure UART pins completely via mpconfigboard.h. 2015-05-02 16:31:39 +00:00			`// UART config`
stmhal: Refactor UART configuration to use pin objects. This follows the pattern of other peripherals (I2C, SPI) to specify the pins using pin objects instead of a pair of GPIO port and pin number. It makes it easier to customise the UART pins for a particular board. 2016-12-05 01:21:45 +00:00			`#define MICROPY_HW_UART1_TX (pin_A9)`
			`#define MICROPY_HW_UART1_RX (pin_A10)`
			`#define MICROPY_HW_UART2_TX (pin_A2)`
			`#define MICROPY_HW_UART2_RX (pin_A3)`
			`#define MICROPY_HW_UART2_RTS (pin_A1)`
			`#define MICROPY_HW_UART2_CTS (pin_A0)`
			`#define MICROPY_HW_UART3_TX (pin_D8)`
			`#define MICROPY_HW_UART3_RX (pin_D9)`
			`#define MICROPY_HW_UART3_RTS (pin_D12)`
			`#define MICROPY_HW_UART3_CTS (pin_D11)`
			`#define MICROPY_HW_UART4_TX (pin_A0)`
			`#define MICROPY_HW_UART4_RX (pin_A1)`
			`#define MICROPY_HW_UART5_TX (pin_C12)`
			`#define MICROPY_HW_UART5_RX (pin_D2)`
			`#define MICROPY_HW_UART6_TX (pin_C6)`
			`#define MICROPY_HW_UART6_RX (pin_C7)`
stmhal: Allow to configure UART pins completely via mpconfigboard.h. 2015-05-02 16:31:39 +00:00
all: Replace busses with buses. "buses" is the widely accepted plural form of "bus". 2021-05-20 06:21:47 +00:00			`// I2C buses`
stmhal: Make I2C busses and their pins configurable in mpconfigboard.h. 2015-04-18 15:12:57 +00:00			`#define MICROPY_HW_I2C1_SCL (pin_B6)`
			`#define MICROPY_HW_I2C1_SDA (pin_B7)`
			`#define MICROPY_HW_I2C2_SCL (pin_B10)`
			`#define MICROPY_HW_I2C2_SDA (pin_B11)`
stmhal: CERB40 - Add pins defines for I2C3 2016-02-11 05:25:30 +00:00			`#define MICROPY_HW_I2C3_SCL (pin_A8)`
			`#define MICROPY_HW_I2C3_SDA (pin_C9)`
stmhal: Make I2C busses and their pins configurable in mpconfigboard.h. 2015-04-18 15:12:57 +00:00
all: Replace busses with buses. "buses" is the widely accepted plural form of "bus". 2021-05-20 06:21:47 +00:00			`// SPI buses`
stmhal: For SPI config, use HW_SPIx_SCK instead of HW_ENABLE_SPIx. Previously, SPI was configured by a board defining MICROPY_HW_ENABLE_SPIx to 0 or 1. Now, the board should define MICROPY_HW_SPIx_SCK, MISO, MOSI and NSS. This makes it the same as how I2C is configured. 2015-12-12 15:02:02 +00:00			`#define MICROPY_HW_SPI1_NSS (pin_A4)`
			`#define MICROPY_HW_SPI1_SCK (pin_A5)`
			`#define MICROPY_HW_SPI1_MISO (pin_A6)`
			`#define MICROPY_HW_SPI1_MOSI (pin_A7)`
			`#define MICROPY_HW_SPI3_NSS (pin_A4)`
			`#define MICROPY_HW_SPI3_SCK (pin_B3)`
			`#define MICROPY_HW_SPI3_MISO (pin_B4)`
			`#define MICROPY_HW_SPI3_MOSI (pin_B5)`

all: Replace busses with buses. "buses" is the widely accepted plural form of "bus". 2021-05-20 06:21:47 +00:00			`// CAN buses`
stm32/can: Allow CAN pins to be configured per board. This patch allows a given board to configure which pins are used for the CAN peripherals, in a similar way to all the other bus peripherals (I2C, UART, SPI). To enable CAN on a board the mpconfigboard.h file should define (for example): #define MICROPY_HW_CAN1_TX (pin_B9) #define MICROPY_HW_CAN1_RX (pin_B8) #define MICROPY_HW_CAN2_TX (pin_B13) #define MICROPY_HW_CAN2_RX (pin_B12) And the board config file should no longer define MICROPY_HW_ENABLE_CAN. 2018-04-11 06:27:48 +00:00			`#define MICROPY_HW_CAN1_TX (pin_B9)`
			`#define MICROPY_HW_CAN1_RX (pin_B8)`
			`#define MICROPY_HW_CAN2_TX (pin_B13)`
			`#define MICROPY_HW_CAN2_RX (pin_B12)`

stmhal: Add support for FEZ Cerb40 II board from ghielectronics.com. 2015-01-16 05:45:21 +00:00			`// The Cerb40 has No LEDs`

			`// The Cerb40 has No SDCard`

			`// USB config`
stm32/boards: Update all boards to work with new USB configuration. 2018-02-13 07:57:01 +00:00			`#define MICROPY_HW_USB_FS (1)`
stmhal: Add support for FEZ Cerb40 II board from ghielectronics.com. 2015-01-16 05:45:21 +00:00			`//#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_A9)`
			`//#define MICROPY_HW_USB_OTG_ID_PIN (pin_A10)`