micropython-samples

A place for assorted code ideas for MicroPython. Most are targeted at the Pyboard variants.

Fastbuild

Scripts for building MicroPython for various target hardware types and for updating your local source. See docs

SSD1306

A means of rendering multiple larger fonts to the SSD1306 OLED display. The Writer class which performs this has been substantially improved and may now be found as part of this repository.

mutex

A class providing mutual exclusion enabling interrupt handlers and the main program to access shared data in a manner which ensures data integrity.

watchdog

Access the simpler of the Pyboard's watchdog timers.

reverse

Fast reverse a bytearray in Arm Thumb assembler.
Python code to bit-reverse (fast-ish) 8, 16 and 32 bit words.

DS3231

This is a low cost precision battery backed real time clock (RTC) accurate to +-2 minutes/year. Two drivers are provided, one portable across platforms and one which is Pyboard specific.

The Pyboard-specific driver provides a facility to calibrate the Pyboard's RTC from the DS3231. Calibration to high precision may be achieved in five minutes.

The drivers are documented here.

Buildcheck

Raise an exception if a firmware build is earlier than a given date.

timed_function

Time a function's execution using a decorator. Also a way to implement timeouts using a closure.

ESP8266 (MQTT benchmark)

benchmark.py Tests the performance of MQTT by periodically publishing while subscribed to the same topic. Measures the round-trip delay. Adapt to suit your server address and desired QOS (quality of service, 0 and 1 are supported). After 100 messages reports maximum and minimum delays.

conn.py Connect in station mode using saved connection details where possible.

resilient

A guide to writing reliable ESP8266 networking code. Probably applies to other WiFi connected MicroPython devices, but reliable ones are thin on the ground.

Rotary Incremental Encoder

Classes for handling incremental rotary position encoders. Note that the Pyboard timers can do this in hardware. These samples cater for cases where that solution can't be used. The encoder_timed.py sample provides rate information by timing successive edges. In practice this is likely to need filtering to reduce jitter caused by imperfections in the encoder geometry.

There are other algorithms but this is the simplest and fastest I've encountered.

These were written for encoders producing TTL outputs. For switches, adapt the pull definition to provide a pull up or pull down as required.

The encoder.portable.py version should work on all MicroPython platforms. Tested on ESP8266. Note that interrupt latency on the ESP8266 limits performance. ESP32 has similar limitations.

A pseudo random number generator

On the Pyboard V1.1, true random numbers may be generated rapidly with pyb.rng() which uses a hardware random number generator on the microcontroller.

There are two use cases for the pseudo random number generator. Firstly on platforms lacking a hardware generator (e.g. the Pyboard Lite). And secondly where repeatable results are required, for example in testing. A pseudo random number generator is seeded with an arbitrary initial value. On each call to the function it will return a random number, but (given the same seed) the sequence of numbers following initialisation will always be the same.

See the code for usage and timing documentation.

micropip

This is a version of upip which runs under Python 3.2 or above. It is intended for users of hardware which is not network enabled. Libraries may be installed to the PC for transfer to the target. Usage is the same as for the official upip.py and help may be accessed with

micropip.py --help

or

python3 -m micropip --help

Its advantage over running upip.py on a PC is that it avoids the need for a Linux installation and having to compile the Unix build of MicroPython.

Measurement of relative timing and phase of fast analog signals

This describes ways of using the Pyboard to perform precision measurements of analog signals of up to around 50KHz. It is documented here.

A design for a hardware power meter

This uses a Pyboard to measure the power consumption of mains powered devices. Unlike simple commercial devices it performs a true vector (phasor) measurement enabling it to provide information on power factor and to work with devices which generate as well as consume power. It uses the official LCD160CR display as a touch GUI interface. It is documented here.

License

Any code placed here is released under the MIT License (MIT).
The MIT License (MIT)
Copyright (c) 2016 Peter Hinch
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions: The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software. THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.