kopia lustrzana https://github.com/peterhinch/micropython-micro-gui
60 wiersze
2.1 KiB
Python
60 wiersze
2.1 KiB
Python
# pico_epaper_42.py on my PCB (non-standard connection)
|
|
|
|
# Released under the MIT License (MIT). See LICENSE.
|
|
# Copyright (c) 2023 Peter Hinch
|
|
|
|
# This Hardware_setup.py is for # https://www.waveshare.com/pico-epaper-4.2.htm
|
|
# wired to the Pico using the ribbon cable rather than the default socket.
|
|
# This was to enable testing using my ILI9341 PCB and its pushbuttons.
|
|
# Use commented-out code below if using the built-in Pico socket.
|
|
|
|
# WIRING
|
|
# Pico Display
|
|
# GPIO Pin
|
|
# 3v3 36 Vin
|
|
# IO6 9 CLK Hardware SPI0
|
|
# IO7 10 DATA (AKA SI MOSI)
|
|
# IO8 11 DC
|
|
# IO9 12 Rst
|
|
# Gnd 13 Gnd
|
|
# IO10 14 CS
|
|
|
|
# Pushbuttons are wired between the pin and Gnd
|
|
# Pico pin Meaning
|
|
# 16 Operate current control
|
|
# 17 Decrease value of current control
|
|
# 18 Select previous control
|
|
# 19 Select next control
|
|
# 20 Increase value of current control
|
|
|
|
from machine import Pin, SPI, freq
|
|
import gc
|
|
from drivers.epaper.pico_epaper_42 import EPD as SSD
|
|
freq(250_000_000) # RP2 overclock
|
|
# Create and export an SSD instance
|
|
prst = Pin(9, Pin.OUT, value=1)
|
|
pcs = Pin(10, Pin.OUT, value=1)
|
|
pdc = Pin(8, Pin.OUT, value=0) # Arbitrary pins
|
|
busy = Pin(15, Pin.IN)
|
|
# Datasheet allows 10MHz
|
|
spi = SPI(0, sck=Pin(6), mosi=Pin(7), miso=Pin(4), baudrate=10_000_000)
|
|
gc.collect() # Precaution before instantiating framebuf
|
|
|
|
# Using normal socket connection default args apply
|
|
# ssd = SSD()
|
|
ssd = SSD(spi, pcs, pdc, prst, busy)
|
|
gc.collect()
|
|
from gui.core.ugui import Display, quiet
|
|
# quiet()
|
|
# Create and export a Display instance
|
|
# Define control buttons
|
|
nxt = Pin(19, Pin.IN, Pin.PULL_UP) # Move to next control
|
|
sel = Pin(16, Pin.IN, Pin.PULL_UP) # Operate current control
|
|
prev = Pin(18, Pin.IN, Pin.PULL_UP) # Move to previous control
|
|
increase = Pin(20, Pin.IN, Pin.PULL_UP) # Increase control's value
|
|
decrease = Pin(17, Pin.IN, Pin.PULL_UP) # Decrease control's value
|
|
# display = Display(ssd, nxt, sel, prev) # 3-button mode
|
|
display = Display(ssd, nxt, sel, prev, increase, decrease) # 5-button mode
|
|
ssd.wait_until_ready() # Blocking wait
|
|
ssd.set_partial() # Subsequent refreshes are partial
|