kopia lustrzana https://github.com/meshtastic/firmware
108 wiersze
1.9 KiB
YAML
108 wiersze
1.9 KiB
YAML
### Define your devices here using Broadcom pin numbering
|
|
### Uncomment the block that corresponds to your hardware
|
|
---
|
|
Lora:
|
|
# Module: sx1262 # Waveshare SX126X XXXM
|
|
# DIO2_AS_RF_SWITCH: true
|
|
# CS: 21
|
|
# IRQ: 16
|
|
# Busy: 20
|
|
# Reset: 18
|
|
|
|
# Module: sx1262 # Waveshare SX1302 LISTEN ONLY AT THIS TIME!
|
|
# CS: 7
|
|
# IRQ: 17
|
|
# Reset: 22
|
|
|
|
# Module: sx1262 # pinedio
|
|
# CS: 0
|
|
# IRQ: 10
|
|
# Busy: 11
|
|
# spidev: spidev0.1
|
|
|
|
# Module: RF95 # Adafruit RFM9x
|
|
# Reset: 25
|
|
# CS: 7
|
|
# IRQ: 22
|
|
# Busy: 23
|
|
|
|
# Module: RF95 # Elecrow Lora RFM95 IOT https://www.elecrow.com/lora-rfm95-iot-board-for-rpi.html
|
|
# Reset: 22
|
|
# CS: 7
|
|
# IRQ: 25
|
|
|
|
# Module: sx1280 # SX1280
|
|
# CS: 21
|
|
# IRQ: 16
|
|
# Busy: 20
|
|
# Reset: 18
|
|
|
|
# DIO3_TCXO_VOLTAGE: true # the Waveshare Core1262 and others are known to need this setting
|
|
|
|
# TXen: x # TX and RX enable pins
|
|
# RXen: x
|
|
|
|
### Set gpio chip to use in /dev/. Defaults to 0.
|
|
### Notably the Raspberry Pi 5 puts the GPIO header on gpiochip4
|
|
# gpiochip: 4
|
|
|
|
### Specify the SPI device to use in /dev/. Defaults to spidev0.0
|
|
### Some devices, like the pinedio, may require spidev0.1 as a workaround.
|
|
# spidev: spidev0.0
|
|
|
|
### Define GPIO buttons here:
|
|
|
|
GPIO:
|
|
# User: 6
|
|
|
|
### Define GPS
|
|
|
|
GPS:
|
|
# SerialPath: /dev/ttyS0
|
|
|
|
### Specify I2C device, or leave blank for none
|
|
|
|
I2C:
|
|
# I2CDevice: /dev/i2c-1
|
|
|
|
### Set up SPI displays here. Note that I2C displays are generally auto-detected.
|
|
|
|
Display:
|
|
|
|
### Waveshare 2.8inch RPi LCD
|
|
# Panel: ST7789
|
|
# CS: 8
|
|
# DC: 22 # Data/Command pin
|
|
# Backlight: 18
|
|
# Width: 240
|
|
# Height: 320
|
|
# Reset: 27
|
|
# Rotate: true
|
|
# Invert: true
|
|
|
|
### Waveshare 1.44inch LCD HAT
|
|
# Panel: ST7735S
|
|
# CS: 8 #Chip Select
|
|
# DC: 25 # Data/Command pin
|
|
# Backlight: 24
|
|
# Width: 128
|
|
# Height: 128
|
|
# Reset: 27
|
|
# OffsetX: 0
|
|
# OffsetY: 0
|
|
|
|
Touchscreen:
|
|
# Module: XPT2046
|
|
# CS: 7
|
|
# IRQ: 17
|
|
|
|
### Configure device for direct keyboard input
|
|
|
|
Input:
|
|
# KeyboardDevice: /dev/input/event0
|
|
|
|
###
|
|
|
|
Logging:
|
|
# DebugMode: true
|