kopia lustrzana https://github.com/meshtastic/firmware
81 wiersze
2.1 KiB
C
81 wiersze
2.1 KiB
C
/*
|
|
|
|
*/
|
|
#define HAS_GPS 0
|
|
#undef GPS_RX_PIN
|
|
#undef GPS_TX_PIN
|
|
|
|
#define EXT_NOTIFY_OUT 22
|
|
#define BUTTON_PIN 0 // 17
|
|
|
|
// #define LED_PIN PIN_LED
|
|
// Board has RGB LED 21
|
|
#define HAS_NEOPIXEL // Enable the use of neopixels
|
|
#define NEOPIXEL_COUNT 1 // How many neopixels are connected
|
|
#define NEOPIXEL_DATA 21 // gpio pin used to send data to the neopixels
|
|
#define NEOPIXEL_TYPE (NEO_GRB + NEO_KHZ800) // type of neopixels in use
|
|
|
|
// The usbPower state is revered ?
|
|
// DEBUG | ??:??:?? 365 [Power] Battery: usbPower=0, isCharging=0, batMv=4116, batPct=90
|
|
// DEBUG | ??:??:?? 385 [Power] Battery: usbPower=1, isCharging=1, batMv=4243, batPct=0
|
|
|
|
// https://www.waveshare.com/img/devkit/ESP32-S3-Pico/ESP32-S3-Pico-details-inter-1.jpg
|
|
// digram is incorrect labeled as battery pin is getting readings on GPIO7_CH1?
|
|
#define BATTERY_PIN 7
|
|
#define ADC_CHANNEL ADC1_GPIO7_CHANNEL
|
|
// #define ADC_CHANNEL ADC1_GPIO6_CHANNEL
|
|
// ratio of voltage divider = 3.0 (R17=200k, R18=100k)
|
|
#define ADC_MULTIPLIER 3.1 // 3.0 + a bit for being optimistic
|
|
|
|
#define I2C_SDA 15
|
|
#define I2C_SCL 16
|
|
|
|
// Enable secondary bus for external periherals
|
|
// https://www.waveshare.com/wiki/Pico-OLED-1.3
|
|
// #define USE_SH1107_128_64
|
|
// Not working
|
|
#define I2C_SDA1 17
|
|
#define I2C_SCL1 18
|
|
|
|
#define BUTTON_PIN 0 // This is the BOOT button
|
|
#define BUTTON_NEED_PULLUP
|
|
|
|
// #define USE_RF95 // RFM95/SX127x
|
|
#define USE_SX1262
|
|
// #define USE_SX1280
|
|
|
|
#define LORA_MISO 37
|
|
#define LORA_SCK 35
|
|
#define LORA_MOSI 36
|
|
#define LORA_CS 14
|
|
|
|
#define LORA_RESET 40
|
|
#define LORA_DIO1 4
|
|
#define LORA_DIO2 13
|
|
|
|
#ifdef USE_SX1262
|
|
#define SX126X_CS LORA_CS
|
|
#define SX126X_DIO1 LORA_DIO1
|
|
#define SX126X_BUSY LORA_DIO2
|
|
#define SX126X_RESET LORA_RESET
|
|
#define SX126X_DIO2_AS_RF_SWITCH
|
|
#define SX126X_DIO3_TCXO_VOLTAGE 1.8
|
|
#endif
|
|
|
|
#ifdef USE_SX1280
|
|
#define SX128X_CS LORA_CS
|
|
#define SX128X_DIO1 LORA_DIO1
|
|
#define SX128X_BUSY 9
|
|
#define SX128X_RESET LORA_RESET
|
|
#endif
|
|
|
|
#define USE_EINK
|
|
/*
|
|
* eink display pins
|
|
*/
|
|
#define PIN_EINK_CS 34
|
|
#define PIN_EINK_BUSY 38
|
|
#define PIN_EINK_DC 33
|
|
#define PIN_EINK_RES 42 // 37 //(-1) // cant be MISO Waveshare ??)
|
|
#define PIN_EINK_SCLK 35
|
|
#define PIN_EINK_MOSI 36 |