kopia lustrzana https://github.com/meshtastic/firmware
71 wiersze
2.1 KiB
C
71 wiersze
2.1 KiB
C
// meshtastic/firmware/variants/unphone/variant.h
|
|
|
|
#pragma once
|
|
|
|
#define SPI_SCK 39
|
|
#define SPI_MOSI 40
|
|
#define SPI_MISO 41
|
|
|
|
// We use the RFM95W LoRa module
|
|
#define USE_RF95
|
|
#define LORA_SCK SPI_SCK
|
|
#define LORA_MOSI SPI_MOSI
|
|
#define LORA_MISO SPI_MISO
|
|
#define LORA_CS 44
|
|
#define LORA_DIO0 10 // AKA LORA_IRQ
|
|
#define LORA_RESET 42
|
|
#define LORA_DIO1 11
|
|
#define LORA_DIO2 RADIOLIB_NC // Not really used
|
|
|
|
// HX8357 TFT LCD
|
|
#define HX8357_CS 48
|
|
#define HX8357_RS 47 // AKA DC
|
|
#define HX8357_RESET 46
|
|
#define HX8357_SCK SPI_SCK
|
|
#define HX8357_MOSI SPI_MOSI
|
|
#define HX8357_MISO SPI_MISO
|
|
#define HX8357_BUSY -1
|
|
#define HX8357_SPI_HOST SPI2_HOST
|
|
#define SPI_FREQUENCY 40000000
|
|
#define SPI_READ_FREQUENCY 16000000
|
|
#define TFT_HEIGHT 480
|
|
#define TFT_WIDTH 320
|
|
#define TFT_OFFSET_X 0
|
|
#define TFT_OFFSET_Y 0
|
|
#define TFT_OFFSET_ROTATION 6 // unPhone's screen wired unusually, 0 typical
|
|
#define TFT_INVERT false
|
|
#define SCREEN_ROTATE true
|
|
#define SCREEN_TRANSITION_FRAMERATE 5
|
|
|
|
#define HAS_TOUCHSCREEN 1
|
|
#define USE_XPT2046 1
|
|
#define TOUCH_CS 38
|
|
|
|
#define HAS_GPS \
|
|
0 // the unphone doesn't have a gps module by default (though
|
|
// GPS featherwing -- https://www.adafruit.com/product/3133
|
|
// -- can be added)
|
|
#undef GPS_RX_PIN
|
|
#undef GPS_TX_PIN
|
|
|
|
// #define HAS_SDCARD 1 // causes hang if defined
|
|
#define SDCARD_CS 43
|
|
|
|
#define LED_PIN 13 // the red part of the RGB LED
|
|
#define LED_INVERTED 1
|
|
|
|
#define BUTTON_PIN 21 // Button 3 - square - top button in landscape mode
|
|
#define BUTTON_NEED_PULLUP // we do need a helping hand up
|
|
#define BUTTON_PIN_ALT 45 // Button 1 - triangle - bottom button in landscape mode
|
|
|
|
#define I2C_SDA 3 // I2C pins for this board
|
|
#define I2C_SCL 4
|
|
|
|
#define LSM6DS3_WAKE_THRESH 5 // higher values reduce the sensitivity of the wake threshold
|
|
|
|
// ratio of voltage divider = 3.20 (R1=100k, R2=220k)
|
|
// #define ADC_MULTIPLIER 3.2
|
|
|
|
// #define BATTERY_PIN 13 // battery V measurement pin; vbat divider is here
|
|
// #define ADC_CHANNEL ADC2_GPIO13_CHANNEL
|
|
// #define BAT_MEASURE_ADC_UNIT 2
|