kopia lustrzana https://github.com/meshtastic/firmware
92 wiersze
2.5 KiB
C
92 wiersze
2.5 KiB
C
// ST7789 TFT LCD
|
|
#define ST7789_CS 12
|
|
#define ST7789_RS 11 // DC
|
|
#define ST7789_SDA 41 // MOSI
|
|
#define ST7789_SCK 40
|
|
#define ST7789_RESET -1
|
|
#define ST7789_MISO 38
|
|
#define ST7789_BUSY -1
|
|
#define ST7789_BL 42
|
|
#define ST7789_SPI_HOST SPI2_HOST
|
|
#define ST7789_BACKLIGHT_EN 42
|
|
#define SPI_FREQUENCY 40000000
|
|
#define SPI_READ_FREQUENCY 16000000
|
|
#define TFT_HEIGHT 320
|
|
#define TFT_WIDTH 240
|
|
#define TFT_OFFSET_X 0
|
|
#define TFT_OFFSET_Y 0
|
|
#define TFT_OFFSET_ROTATION 0
|
|
#define SCREEN_ROTATE
|
|
#define SCREEN_TRANSITION_FRAMERATE 5
|
|
|
|
#define HAS_TOUCHSCREEN 1
|
|
#define SCREEN_TOUCH_INT 16
|
|
#define TOUCH_I2C_PORT 0
|
|
#define TOUCH_SLAVE_ADDRESS 0x5D // GT911
|
|
|
|
#define BUTTON_PIN 0
|
|
// #define BUTTON_NEED_PULLUP
|
|
|
|
#define GPS_RX_PIN 44
|
|
#define GPS_TX_PIN 43
|
|
|
|
// Have SPI interface SD card slot
|
|
#define HAS_SDCARD 1
|
|
#define SPI_MOSI (41)
|
|
#define SPI_SCK (40)
|
|
#define SPI_MISO (38)
|
|
#define SPI_CS (39)
|
|
#define SDCARD_CS SPI_CS
|
|
|
|
#define BATTERY_PIN 4 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
|
|
// ratio of voltage divider = 2.0 (RD2=100k, RD3=100k)
|
|
#define ADC_MULTIPLIER 2.11 // 2.0 + 10% for correction of display undervoltage.
|
|
#define ADC_CHANNEL ADC1_GPIO4_CHANNEL
|
|
|
|
// keyboard
|
|
#define I2C_SDA 18 // I2C pins for this board
|
|
#define I2C_SCL 8
|
|
#define KB_POWERON 10 // must be set to HIGH
|
|
#define KB_SLAVE_ADDRESS TDECK_KB_ADDR // 0x55
|
|
#define KB_BL_PIN 46 // not used for now
|
|
#define CANNED_MESSAGE_MODULE_ENABLE 1
|
|
|
|
// trackball
|
|
#define HAS_TRACKBALL 1
|
|
#define TB_UP 3
|
|
#define TB_DOWN 15
|
|
#define TB_LEFT 1
|
|
#define TB_RIGHT 2
|
|
#define TB_PRESS BUTTON_PIN
|
|
|
|
// microphone
|
|
#define ES7210_SCK 47
|
|
#define ES7210_DIN 14
|
|
#define ES7210_LRCK 21
|
|
#define ES7210_MCLK 48
|
|
|
|
// LoRa
|
|
#define USE_SX1262
|
|
#define USE_SX1268
|
|
|
|
#define LORA_SCK 40
|
|
#define LORA_MISO 38
|
|
#define LORA_MOSI 41
|
|
#define LORA_CS 9
|
|
|
|
#define LORA_DIO0 -1 // a No connect on the SX1262 module
|
|
#define LORA_RESET 17
|
|
#define LORA_DIO1 45 // SX1262 IRQ
|
|
#define LORA_DIO2 13 // SX1262 BUSY
|
|
#define LORA_DIO3 // Not connected on PCB, but internally on the TTGO SX1262, if DIO3 is high the TXCO is enabled
|
|
|
|
#define SX126X_CS LORA_CS // FIXME - we really should define LORA_CS instead
|
|
#define SX126X_DIO1 LORA_DIO1
|
|
#define SX126X_BUSY LORA_DIO2
|
|
#define SX126X_RESET LORA_RESET
|
|
// Not really an E22 but TTGO seems to be trying to clone that
|
|
#define SX126X_DIO2_AS_RF_SWITCH
|
|
#define SX126X_DIO3_TCXO_VOLTAGE 1.8
|
|
// Internally the TTGO module hooks the SX1262-DIO2 in to control the TX/RX switch (which is the default for the sx1262interface
|
|
// code)
|