kopia lustrzana https://github.com/meshtastic/firmware
72 wiersze
2.0 KiB
C
72 wiersze
2.0 KiB
C
#define LED_PIN 18
|
|
|
|
#define HELTEC_TRACKER_V1_X
|
|
|
|
// I2C
|
|
#define I2C_SDA SDA
|
|
#define I2C_SCL SCL
|
|
|
|
// ST7735S TFT LCD
|
|
#define ST7735S 1 // there are different (sub-)versions of ST7735
|
|
#define ST7735_CS 38
|
|
#define ST7735_RS 40 // DC
|
|
#define ST7735_SDA 42 // MOSI
|
|
#define ST7735_SCK 41
|
|
#define ST7735_RESET 39
|
|
#define ST7735_MISO -1
|
|
#define ST7735_BUSY -1
|
|
#define ST7735_BL_V03 45
|
|
#define ST7735_SPI_HOST SPI3_HOST
|
|
#define SPI_FREQUENCY 40000000
|
|
#define SPI_READ_FREQUENCY 16000000
|
|
#define SCREEN_ROTATE
|
|
#define TFT_HEIGHT DISPLAY_WIDTH
|
|
#define TFT_WIDTH DISPLAY_HEIGHT
|
|
#define TFT_OFFSET_X 26
|
|
#define TFT_OFFSET_Y -1
|
|
#define VTFT_CTRL_V03 46 // Heltec Tracker needs this pulled low for TFT
|
|
#define SCREEN_TRANSITION_FRAMERATE 3 // fps
|
|
#define DISPLAY_FORCE_SMALL_FONTS
|
|
|
|
#define VEXT_ENABLE_V03 Vext // active low, powers the oled display and the lora antenna boost
|
|
#define BUTTON_PIN 0
|
|
|
|
#define BATTERY_PIN 1 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
|
|
#define ADC_CHANNEL ADC1_GPIO1_CHANNEL
|
|
#define ADC_ATTENUATION ADC_ATTEN_DB_2_5 // lower dB for high resistance voltage divider
|
|
#define ADC_MULTIPLIER 4.9 * 1.045
|
|
|
|
#undef GPS_RX_PIN
|
|
#undef GPS_TX_PIN
|
|
#define GPS_RX_PIN 33
|
|
#define GPS_TX_PIN 34
|
|
#define PIN_GPS_RESET 35
|
|
#define PIN_GPS_PPS 36
|
|
|
|
#define VGNSS_CTRL_V03 37 // Heltec Tracker needs this pulled low for GPS
|
|
#define PIN_GPS_EN VGNSS_CTRL_V03
|
|
#define GPS_EN_ACTIVE LOW
|
|
|
|
#define GPS_RESET_MODE LOW
|
|
#define GPS_UC6580
|
|
|
|
#define USE_SX1262
|
|
#define LORA_DIO0 -1 // a No connect on the SX1262 module
|
|
#define LORA_RESET 12
|
|
#define LORA_DIO1 14 // SX1262 IRQ
|
|
#define LORA_DIO2 13 // SX1262 BUSY
|
|
#define LORA_DIO3 // Not connected on PCB, but internally on the TTGO SX1262, if DIO3 is high the TXCO is enabled
|
|
|
|
#define LORA_SCK 9
|
|
#define LORA_MISO 11
|
|
#define LORA_MOSI 10
|
|
#define LORA_CS 8
|
|
|
|
#define SX126X_CS LORA_CS
|
|
#define SX126X_DIO1 LORA_DIO1
|
|
#define SX126X_BUSY LORA_DIO2
|
|
#define SX126X_RESET LORA_RESET
|
|
|
|
#define SX126X_DIO2_AS_RF_SWITCH
|
|
#define SX126X_DIO3_TCXO_VOLTAGE 1.8
|