kopia lustrzana https://github.com/meshtastic/firmware
94 wiersze
3.0 KiB
C
94 wiersze
3.0 KiB
C
#define LED_PIN 18
|
|
|
|
#define HELTEC_TRACKER_V1_X
|
|
|
|
// TRACKSENGER 2.42" I2C OLED
|
|
|
|
// I2C
|
|
#define I2C_SDA 42
|
|
#define I2C_SCL 41
|
|
#define HAS_SCREEN 1
|
|
#define USE_SSD1306
|
|
|
|
// ST7735S TFT LCD
|
|
// #define ST7735S 1 // there are different (sub-)versions of ST7735
|
|
// #define ST7735_CS 38
|
|
// #define ST7735_RS 40 // DC
|
|
// #define ST7735_SDA 42 // MOSI
|
|
// #define ST7735_SCK 41
|
|
// #define ST7735_RESET 39
|
|
// #define ST7735_MISO -1
|
|
// #define ST7735_BUSY -1
|
|
#define ST7735_BL_V05 21 /* V1.1 PCB marking */
|
|
// #define ST7735_SPI_HOST SPI3_HOST
|
|
// #define SPI_FREQUENCY 40000000
|
|
// #define SPI_READ_FREQUENCY 16000000
|
|
// #define SCREEN_ROTATE
|
|
// #define TFT_HEIGHT DISPLAY_WIDTH
|
|
// #define TFT_WIDTH DISPLAY_HEIGHT
|
|
// #define TFT_OFFSET_X 26
|
|
// #define TFT_OFFSET_Y -1
|
|
#define SCREEN_TRANSITION_FRAMERATE 3 // fps
|
|
// #define DISPLAY_FORCE_SMALL_FONTS
|
|
|
|
#define VEXT_ENABLE_V05 3 // active HIGH, powers the lora antenna boost
|
|
#define BUTTON_PIN 0
|
|
|
|
#define BATTERY_PIN 1 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
|
|
#define ADC_CHANNEL ADC1_GPIO1_CHANNEL
|
|
#define ADC_ATTENUATION ADC_ATTEN_DB_2_5 // lower dB for high resistance voltage divider
|
|
#define ADC_MULTIPLIER 4.9
|
|
#define ADC_CTRL 2 // active HIGH, powers the voltage divider. Only on 1.1
|
|
#define ADC_CTRL_ENABLED HIGH
|
|
|
|
#undef GPS_RX_PIN
|
|
#undef GPS_TX_PIN
|
|
#define GPS_RX_PIN 33
|
|
#define GPS_TX_PIN 34
|
|
#define PIN_GPS_RESET 35
|
|
#define PIN_GPS_PPS 36
|
|
|
|
#define GPS_RESET_MODE LOW
|
|
#define GPS_UC6580
|
|
#define GPS_BAUDRATE 115200
|
|
|
|
#define USE_SX1262
|
|
#define LORA_DIO0 -1 // a No connect on the SX1262 module
|
|
#define LORA_RESET 12
|
|
#define LORA_DIO1 14 // SX1262 IRQ
|
|
#define LORA_DIO2 13 // SX1262 BUSY
|
|
#define LORA_DIO3 // Not connected on PCB, but internally on the TTGO SX1262, if DIO3 is high the TXCO is enabled
|
|
|
|
#define LORA_SCK 9
|
|
#define LORA_MISO 11
|
|
#define LORA_MOSI 10
|
|
#define LORA_CS 8
|
|
|
|
#define SX126X_CS LORA_CS
|
|
#define SX126X_DIO1 LORA_DIO1
|
|
#define SX126X_BUSY LORA_DIO2
|
|
#define SX126X_RESET LORA_RESET
|
|
|
|
#define SX126X_DIO2_AS_RF_SWITCH
|
|
#define SX126X_DIO3_TCXO_VOLTAGE 1.8
|
|
|
|
// Picomputer gets a white on black display
|
|
#define TFT_MESH COLOR565(0xFF, 0xFF, 0xFF)
|
|
|
|
// keyboard changes
|
|
|
|
#define PIN_BUZZER 43
|
|
#define CANNED_MESSAGE_MODULE_ENABLE 1
|
|
|
|
#define INPUTBROKER_MATRIX_TYPE 1
|
|
|
|
#define KEYS_COLS \
|
|
{ \
|
|
44, 45, 46, 4, 5, 6 \
|
|
}
|
|
#define KEYS_ROWS \
|
|
{ \
|
|
26, 37, 17, 16, 15, 7 \
|
|
}
|
|
// #end keyboard
|