* Add LINK32 (Lilygo) Board with Light+Environment sensors
TODO: replace PRIVATE_HW with actual HWID
* Add LINK32 (Lilygo) Board with Light+Environment sensors
TODO: replace PRIVATE_HW with actual HWID
* Update to real HWID and trunk fmt
- Rename REGULATORY_GAIN_LORA to TX_GAIN_LORA
- Move gain-based Tx power clamping from RadioInterface::applyModemConfig() to RadioInterface::limitPower()
- User-configured Tx power now matches the Tx power out of the device connector
- Re-order [LoRa Chip]Interface.cpp limitPower() to take place before the final Tx power clamping so we clamp based on the pre-PA Tx power rather than user-configured Tx power
Tested on XIAO BLE variant.
Signed-off-by: Andrew Yong <me@ndoo.sg>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Custom AdafruitGFX fonts with extended ASCII encodings
* AppletFont handles re-encoding of UTF-8 text
* Manual parsing of text which may contain non-ASCII chars
* Display emoji reactions, even when unprintable
Important to indicate to users that a message has been received, even if meaning is unclear.
* Superstitious shrink_to_fit
I don't think these help, but they're not hurting!
* Use Windows-1252 fonts by default
* Spelling
* Tidy up nicheGraphics.h
* Documentation
* Fix inverted logic
Slipped in during a last minute renaming while tidying up to push..
The XIAO NRF kit comes with a hat which has a slightly different pinout than the one supplied with the XIAO S3. At the last update, the RXEN pin was not moved with the rest.
* support manually shutting off power to the PMSA003I sensor when we aren't doing a telemetry reading
* add comment about PMSA003I_WARMUP_MS to AirQualityTelemetry.cpp
* fix typos, use arduino gpio defines instead of magic numbers
* support manually shutting off power to the PMSA003I sensor when we aren't doing a telemetry reading
* add comment about PMSA003I_WARMUP_MS to AirQualityTelemetry.cpp
* fix typos, use arduino gpio defines instead of magic numbers
* RAK4631: add PMSA003I_ENABLE_PIN define
* fix indentation
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Update platformio.ini to exclude unused modules
* Add No EXT GPIO flag and also correct some exclusions in main
* CANNEDMSG != CANNEDMESSAGES
* Remove NO_EXT_GPIO
* Purge an incomplete E-Ink driver
* Use the deep-sleep mode of SSD16XX E-Ink displays
* TwoButton doesn't need to store pin mode
* Fix false positive button presses after light sleep
* E-Ink driver for DEPG0213BNS800
* InkHUD support for LilyGo T3S3 E-paper
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Fix several features of M1 and M2 (i know what the 7 is now ...)
* 'THe' should be 'The'.
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* remove floating definition
---------
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Only an initial guess. No hardware here yet for testing. Button assignments are largely placeholder.
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* chore: todo.txt
* chore: InkHUD documentation
Word salad for maintainers
* refactor: don't init system applets using onActivate
System applets cannot be deactivated, so we will avoid using onActivate / onDeactivate methods entirely.
* chore: update the example applets
* fix: SSD16XX reset pulse
Allow time for controller IC to wake. Aligns with manufacturer's suggestions.
T-Echo button timing adjusted to prevent bouncing as a result(?) of slightly faster refreshes.
* fix: allow timeout if display update fails
Result is not graceful, but avoids total display lockup requiring power cycle.
Typical cause of failure is poor wiring / power supply.
* fix: improve display health on shutdown
Two extra full refreshes, masquerading as a "shutting down" screen. One is drawn white-on-black, to really shake the pixels up.
* feat: driver for display HINK_E042A87
As of Feb. 2025, these panels are used for "WeActStudio 4.2in B&W" display modules.
* fix: inkhud rotation should default to 0
* Revert "chore: todo.txt"
This reverts commit bea7df44a7.
* fix: more generous timeout for display updates
Previously this was tied to the expected duration of the update, but this didn't account for any delay if our polling thread got held up by an unrelated firmware task.
* fix: don't use the full shutdown screen during reboot
* fix: cooldown period during the display shutdown display sequence
Observed to prevent border pixels from being locked in place with some residual charge?
* [WIP] Base firmware pending support for 2nd button
* Update button behaviour. Still WIP
* [WIP] Base firmware pending support for 2nd button
* Update button behaviour. Still WIP
* change env to lowercase
Co-authored-by: rcarteraz <robert.l.carter2@gmail.com>
* yea - well - what else is new?
* fix secondary button behavior and update trunk
---------
Co-authored-by: rcarteraz <robert.l.carter2@gmail.com>
Co-authored-by: GUVWAF <78759985+GUVWAF@users.noreply.github.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Daniel Peter Chokola <dan.chokola@gmail.com>
Co-authored-by: Mark Trevor Birss <markbirss@gmail.com>
Co-authored-by: Austin <vidplace7@gmail.com>
- Due to the lack of pins, we have temporarily removed the button. There are some technical solutions that can solve this problem, and we are currently exploring and researching them
Thomas Göttgens