mirror
/
meshtastic-firmware
kopia lustrzana https://github.com/meshtastic/firmware
1
0
Forkuj 1
Kod Zgłoszenia Packages Projekty Wydania Wiki Aktywność

fix RF switch for Tracker E (#4621) 

* fix RF switch for Tracker E

* fix all flags for Radiolib

* hopefully fix LR1110

* update to latest radiolib master - thanks @GUVWAF
pull/4608/head^2
Thomas Göttgens 2024-09-03 21:21:40 +02:00 zatwierdzone przez GitHub
rodzic 8b1d7825b9
commit ff40a3f120
Nie znaleziono w bazie danych klucza dla tego podpisu
ID klucza GPG: B5690EEEBB952194
4 zmienionych plików z 21 dodań i 20 usunięć
Pokaż statystyki Ściągnij plik aktualizacji Ściągnij plik porównania Expand all files Collapse all files

2
platformio.ini
Wyświetl plik

@ -88,7 +88,7 @@ monitor_filters = direct
lib_deps =
; jgromes/RadioLib@~6.6.0
https://github.com/jgromes/RadioLib.git#eda4ec22ae0039f3b9a2844d68ac2023ac0076a5
https://github.com/jgromes/RadioLib.git#3115fc2d6700a9aee05888791ac930a910f2628f
https://github.com/meshtastic/esp8266-oled-ssd1306.git#e16cee124fe26490cb14880c679321ad8ac89c95 ; ESP8266_SSD1306
https://github.com/mathertel/OneButton@~2.6.1 ; OneButton library for non-blocking button debounce
https://github.com/meshtastic/arduino-fsm.git#7db3702bf0cfe97b783d6c72595e3f38e0b19159

24
src/mesh/LR11x0Interface.cpp
Wyświetl plik

@ -50,11 +50,23 @@ template <typename T> bool LR11x0Interface<T>::init()
limitPower();
#ifdef TRACKER_T1000_E // Tracker T1000E uses DIO5, DIO6, DIO7, DIO8 for RF switching
static const uint32_t rfswitch_dio_pins[] = {RADIOLIB_LR11X0_DIO5, RADIOLIB_LR11X0_DIO6, RADIOLIB_LR11X0_DIO7,
RADIOLIB_LR11X0_DIO8, RADIOLIB_NC};
static const Module::RfSwitchMode_t rfswitch_table[] = {
// mode DIO5 DIO6 DIO7 DIO8
{LR11x0::MODE_STBY, {LOW, LOW, LOW, LOW}}, {LR11x0::MODE_RX, {HIGH, LOW, LOW, HIGH}},
{LR11x0::MODE_TX, {HIGH, HIGH, LOW, HIGH}}, {LR11x0::MODE_TX_HP, {LOW, HIGH, LOW, HIGH}},
{LR11x0::MODE_TX_HF, {LOW, LOW, LOW, LOW}}, {LR11x0::MODE_GNSS, {LOW, LOW, HIGH, LOW}},
{LR11x0::MODE_WIFI, {LOW, LOW, LOW, LOW}}, END_OF_MODE_TABLE,
};
#else
// set RF switch configuration for Wio WM1110
// Wio WM1110 uses DIO5 and DIO6 for RF switching
// NOTE: other boards may be different. If you are
// using a different board, you may need to wrap
// this in a conditional.
static const uint32_t rfswitch_dio_pins[] = {RADIOLIB_LR11X0_DIO5, RADIOLIB_LR11X0_DIO6, RADIOLIB_NC, RADIOLIB_NC,
RADIOLIB_NC};
@ -67,6 +79,8 @@ template <typename T> bool LR11x0Interface<T>::init()
{LR11x0::MODE_WIFI, {LOW, LOW}}, END_OF_MODE_TABLE,
};
#endif
// We need to do this before begin() call
#ifdef LR11X0_DIO_AS_RF_SWITCH
LOG_DEBUG("Setting DIO RF switch\n");
@ -218,9 +232,7 @@ template <typename T> void LR11x0Interface<T>::startReceive()
// We use a 16 bit preamble so this should save some power by letting radio sit in standby mostly.
// Furthermore, we need the PREAMBLE_DETECTED and HEADER_VALID IRQ flag to detect whether we are actively receiving
int err = lora.startReceive(
RADIOLIB_LR11X0_RX_TIMEOUT_INF, RADIOLIB_LR11X0_IRQ_RX_DONE,
0); // only RX_DONE IRQ is needed, we'll check for PREAMBLE_DETECTED and HEADER_VALID in isActivelyReceiving
int err = lora.startReceive(RADIOLIB_LR11X0_RX_TIMEOUT_INF, RADIOLIB_IRQ_RX_DEFAULT_FLAGS, RADIOLIB_IRQ_RX_DEFAULT_MASK, 0);
assert(err == RADIOLIB_ERR_NONE);
RadioLibInterface::startReceive();

7
src/mesh/SX126xInterface.cpp
Wyświetl plik

@ -12,9 +12,6 @@
#define SX126X_MAX_POWER 22
#endif
#define RADIOLIB_SX126X_IRQ_RX_DEFAULT \
RADIOLIB_SX126X_IRQ_RX_DONE | RADIOLIB_SX126X_IRQ_TIMEOUT | RADIOLIB_SX126X_IRQ_CRC_ERR | RADIOLIB_SX126X_IRQ_HEADER_ERR
template <typename T>
SX126xInterface<T>::SX126xInterface(LockingArduinoHal *hal, RADIOLIB_PIN_TYPE cs, RADIOLIB_PIN_TYPE irq, RADIOLIB_PIN_TYPE rst,
RADIOLIB_PIN_TYPE busy)
@ -267,9 +264,7 @@ template <typename T> void SX126xInterface<T>::startReceive()
// We use a 16 bit preamble so this should save some power by letting radio sit in standby mostly.
// Furthermore, we need the PREAMBLE_DETECTED and HEADER_VALID IRQ flag to detect whether we are actively receiving
int err = lora.startReceiveDutyCycleAuto(preambleLength, 8,
RADIOLIB_SX126X_IRQ_RX_DEFAULT | RADIOLIB_SX126X_IRQ_PREAMBLE_DETECTED |
RADIOLIB_SX126X_IRQ_HEADER_VALID);
int err = lora.startReceiveDutyCycleAuto(preambleLength, 8, RADIOLIB_IRQ_RX_DEFAULT_FLAGS | RADIOLIB_IRQ_PREAMBLE_DETECTED);
if (err != RADIOLIB_ERR_NONE)
LOG_ERROR("Radiolib error %d when attempting SX126X startReceiveDutyCycleAuto!\n", err);
assert(err == RADIOLIB_ERR_NONE);

8
src/mesh/SX128xInterface.cpp
Wyświetl plik

@ -12,10 +12,6 @@
#define SX128X_MAX_POWER 13
#endif
#define RADIOLIB_SX128X_IRQ_RX_DEFAULT \
RADIOLIB_SX128X_IRQ_RX_DONE | RADIOLIB_SX128X_IRQ_RX_TX_TIMEOUT | RADIOLIB_SX128X_IRQ_CRC_ERROR | \
RADIOLIB_SX128X_IRQ_HEADER_ERROR
template <typename T>
SX128xInterface<T>::SX128xInterface(LockingArduinoHal *hal, RADIOLIB_PIN_TYPE cs, RADIOLIB_PIN_TYPE irq, RADIOLIB_PIN_TYPE rst,
RADIOLIB_PIN_TYPE busy)
@ -260,9 +256,7 @@ template <typename T> void SX128xInterface<T>::startReceive()
#endif
// We use the PREAMBLE_DETECTED and HEADER_VALID IRQ flag to detect whether we are actively receiving
int err =
lora.startReceive(RADIOLIB_SX128X_RX_TIMEOUT_INF, RADIOLIB_SX128X_IRQ_RX_DEFAULT | RADIOLIB_SX128X_IRQ_PREAMBLE_DETECTED |
RADIOLIB_SX128X_IRQ_HEADER_VALID);
int err = lora.startReceive(RADIOLIB_SX128X_RX_TIMEOUT_INF, RADIOLIB_IRQ_RX_DEFAULT_FLAGS | RADIOLIB_IRQ_PREAMBLE_DETECTED);
if (err != RADIOLIB_ERR_NONE)
LOG_ERROR("Radiolib error %d when attempting SX128X startReceive!\n", err);