Hydra variant rectification (#2903)

* Update variant.h

* Update variant.h

* Update platformio.ini

variants/diy/hydra/variant.h

@@ -2,44 +2,38 @@
 #define I2C_SDA 21
 #define I2C_SCL 22
 
-// GPS
-#undef GPS_RX_PIN
-#undef GPS_TX_PIN
-#define GPS_RX_PIN 12
+// For GPS, 'undef's not needed
 #define GPS_TX_PIN 15
-#define GPS_UBLOX
+#define GPS_RX_PIN 12
 #define PIN_GPS_EN 4
+#define GPS_POWER_TOGGLE // Moved definition from platformio.ini to here
 
 #define BUTTON_PIN 39  // The middle button GPIO on the T-Beam
 #define BATTERY_PIN 35 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
 #define ADC_CHANNEL ADC1_GPIO35_CHANNEL
 #define ADC_MULTIPLIER 1.85 // (R1 = 470k, R2 = 680k)
-#define EXT_PWR_DETECT 4    // Pin to detect connected external power source for LILYGO® TTGO T-Energy T18 and other DIY boards
-#define EXT_NOTIFY_OUT 12   // Overridden default pin to use for Ext Notify Module (#975).
-#define LED_PIN 2           // add status LED (compatible with core-pcb and DIY targets)
+#define EXT_PWR_DETECT 4 // Pin to detect connected external power source for LILYGO® TTGO T-Energy T18 and other DIY boards
+#define EXT_NOTIFY_OUT 12 // Overridden default pin to use for Ext Notify Module (#975).
+#define LED_PIN 2 // add status LED (compatible with core-pcb and DIY targets)
 
-#define LORA_DIO0 26  // a No connect on the SX1262/SX1268 module
-#define LORA_RESET 23 // RST for SX1276, and for SX1262/SX1268
-#define LORA_DIO1 33  // IRQ for SX1262/SX1268
-#define LORA_DIO2 32  // BUSY for SX1262/SX1268
-#define LORA_DIO3     // Not connected on PCB, but internally on the TTGO SX1262/SX1268, if DIO3 is high the TXCO is enabled
+// Radio
+#define USE_SX1262 // E22-900M30S uses SX1262
+#define SX126X_MAX_POWER 22 // Outputting 22dBm from SX1262 results in ~30dBm E22-900M30S output (module only uses last stage of the YP2233W PA)
+#define SX126X_DIO3_TCXO_VOLTAGE 1.8 // E22 series TCXO reference voltage is 1.8V 
 
-#define RF95_SCK 5
-#define RF95_MISO 19
-#define RF95_MOSI 27
-#define RF95_NSS 18
+#define SX126X_CS 18    // EBYTE module's NSS pin
+#define SX126X_SCK 5    // EBYTE module's SCK pin
+#define SX126X_MOSI 27  // EBYTE module's MOSI pin
+#define SX126X_MISO 19  // EBYTE module's MISO pin
+#define SX126X_RESET 23 // EBYTE module's NRST pin
+#define SX126X_BUSY 32  // EBYTE module's BUSY pin
+#define SX126X_DIO1 33  // EBYTE module's DIO1 pin
 
-#define USE_SX1262
+#define SX126X_TXEN 13 // Schematic connects EBYTE module's TXEN pin to MCU
+#define SX126X_RXEN 14 // Schematic connects EBYTE module's RXEN pin to MCU
 
-#define SX126X_CS 18 // NSS for SX126X
-#define SX126X_DIO1 LORA_DIO1
-#define SX126X_BUSY LORA_DIO2
-#define SX126X_RESET LORA_RESET
-#define SX126X_RXEN 14
-#define SX126X_TXEN RADIOLIB_NC
-#define SX126X_DIO2_AS_RF_SWITCH
-
-// Set lora.tx_power to 13 for Hydra or other E22 900M30S target due to PA
-#define SX126X_MAX_POWER 13
-
-#define SX126X_DIO3_TCXO_VOLTAGE 1.8
+#define RF95_NSS SX126X_CS // Compatibility with variant file configuration structure
+#define RF95_SCK SX126X_SCK // Compatibility with variant file configuration structure
+#define RF95_MOSI SX126X_MOSI // Compatibility with variant file configuration structure
+#define RF95_MISO SX126X_MISO // Compatibility with variant file configuration structure
+#define LORA_DIO1 SX126X_DIO1 // Compatibility with variant file configuration structure

variants/diy/platformio.ini

@@ -43,6 +43,4 @@ board_level = extra
 build_flags =
   ${esp32_base.build_flags}
   -D DIY_V1
-  -D EBYTE_E22
-  -D GPS_POWER_TOGGLE
   -I variants/diy/hydra