diff --git a/variants/tracksenger/internal/pins_arduino.h b/variants/tracksenger/internal/pins_arduino.h new file mode 100644 index 000000000..5c0b529b0 --- /dev/null +++ b/variants/tracksenger/internal/pins_arduino.h @@ -0,0 +1,80 @@ +#ifndef Pins_Arduino_h +#define Pins_Arduino_h + +#include "soc/soc_caps.h" +#include + +#define WIFI_LoRa_32_V3 true +#define DISPLAY_HEIGHT 80 +#define DISPLAY_WIDTH 160 + +#define USB_VID 0x303a +#define USB_PID 0x1001 + +#define EXTERNAL_NUM_INTERRUPTS 46 +#define NUM_DIGITAL_PINS 48 +#define NUM_ANALOG_INPUTS 20 + +static const uint8_t LED_BUILTIN = 18; +#define BUILTIN_LED LED_BUILTIN // backward compatibility +#define LED_BUILTIN LED_BUILTIN + +#define analogInputToDigitalPin(p) (((p) < 20) ? (analogChannelToDigitalPin(p)) : -1) +#define digitalPinToInterrupt(p) (((p) < 48) ? (p) : -1) +#define digitalPinHasPWM(p) (p < 46) + +static const uint8_t TX = 43; +static const uint8_t RX = 44; + +static const uint8_t SDA = 45; +static const uint8_t SCL = 46; + +static const uint8_t SS = 8; +static const uint8_t MOSI = 10; +static const uint8_t MISO = 11; +static const uint8_t SCK = 9; + +static const uint8_t A0 = 1; +static const uint8_t A1 = 2; +static const uint8_t A2 = 3; +static const uint8_t A3 = 4; +static const uint8_t A4 = 5; +static const uint8_t A5 = 6; +static const uint8_t A6 = 7; +static const uint8_t A7 = 8; +static const uint8_t A8 = 9; +static const uint8_t A9 = 10; +static const uint8_t A10 = 11; +static const uint8_t A11 = 12; +static const uint8_t A12 = 13; +static const uint8_t A13 = 14; +static const uint8_t A14 = 15; +static const uint8_t A15 = 16; +static const uint8_t A16 = 17; +static const uint8_t A17 = 18; +static const uint8_t A18 = 19; +static const uint8_t A19 = 20; + +static const uint8_t T1 = 1; +static const uint8_t T2 = 2; +static const uint8_t T3 = 3; +static const uint8_t T4 = 4; +static const uint8_t T5 = 5; +static const uint8_t T6 = 6; +static const uint8_t T7 = 7; +static const uint8_t T8 = 8; +static const uint8_t T9 = 9; +static const uint8_t T10 = 10; +static const uint8_t T11 = 11; +static const uint8_t T12 = 12; +static const uint8_t T13 = 13; +static const uint8_t T14 = 14; + +static const uint8_t Vext = 36; +static const uint8_t LED = 18; + +static const uint8_t RST_LoRa = 12; +static const uint8_t BUSY_LoRa = 13; +static const uint8_t DIO0 = 14; + +#endif /* Pins_Arduino_h */ diff --git a/variants/tracksenger/internal/variant.h b/variants/tracksenger/internal/variant.h new file mode 100644 index 000000000..e63cecd7b --- /dev/null +++ b/variants/tracksenger/internal/variant.h @@ -0,0 +1,90 @@ +#define LED_PIN 18 + +#define HELTEC_TRACKER_V1_X + +// TRACKSENGER builtin LCD + +// I2C +#define I2C_SDA SDA +#define I2C_SCL SCL + +// ST7735S TFT LCD +#define ST7735S 1 // there are different (sub-)versions of ST7735 +#define ST7735_CS 38 +#define ST7735_RS 40 // DC +#define ST7735_SDA 42 // MOSI +#define ST7735_SCK 41 +#define ST7735_RESET 39 +#define ST7735_MISO -1 +#define ST7735_BUSY -1 +#define ST7735_BL_V05 21 /* V1.1 PCB marking */ +#define ST7735_SPI_HOST SPI3_HOST +#define SPI_FREQUENCY 40000000 +#define SPI_READ_FREQUENCY 16000000 +#define SCREEN_ROTATE +#define TFT_HEIGHT DISPLAY_WIDTH +#define TFT_WIDTH DISPLAY_HEIGHT +#define TFT_OFFSET_X 26 +#define TFT_OFFSET_Y -1 +#define SCREEN_TRANSITION_FRAMERATE 3 // fps +#define DISPLAY_FORCE_SMALL_FONTS + +#define VEXT_ENABLE_V05 3 // active HIGH, powers the lora antenna boost +#define BUTTON_PIN 0 + +#define BATTERY_PIN 1 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage +#define ADC_CHANNEL ADC1_GPIO1_CHANNEL +#define ADC_ATTENUATION ADC_ATTEN_DB_2_5 // lower dB for high resistance voltage divider +#define ADC_MULTIPLIER 4.9 +#define ADC_CTRL 2 // active HIGH, powers the voltage divider. Only on 1.1 +#define ADC_CTRL_ENABLED HIGH + +#undef GPS_RX_PIN +#undef GPS_TX_PIN +#define GPS_RX_PIN 33 +#define GPS_TX_PIN 34 +#define PIN_GPS_RESET 35 +#define PIN_GPS_PPS 36 + +#define GPS_RESET_MODE LOW +#define GPS_UC6580 + +#define USE_SX1262 +#define LORA_DIO0 -1 // a No connect on the SX1262 module +#define LORA_RESET 12 +#define LORA_DIO1 14 // SX1262 IRQ +#define LORA_DIO2 13 // SX1262 BUSY +#define LORA_DIO3 // Not connected on PCB, but internally on the TTGO SX1262, if DIO3 is high the TXCO is enabled + +#define LORA_SCK 9 +#define LORA_MISO 11 +#define LORA_MOSI 10 +#define LORA_CS 8 + +#define SX126X_CS LORA_CS +#define SX126X_DIO1 LORA_DIO1 +#define SX126X_BUSY LORA_DIO2 +#define SX126X_RESET LORA_RESET + +#define SX126X_DIO2_AS_RF_SWITCH +#define SX126X_DIO3_TCXO_VOLTAGE 1.8 + +// Picomputer gets a white on black display +#define TFT_MESH COLOR565(0xFF, 0xFF, 0xFF) + +// keyboard changes + +#define PIN_BUZZER 43 +#define CANNED_MESSAGE_MODULE_ENABLE 1 + +#define INPUTBROKER_MATRIX_TYPE 1 + +#define KEYS_COLS \ + { \ + 44, 45, 46, 4, 5, 6 \ + } +#define KEYS_ROWS \ + { \ + 26, 37, 17, 16, 15, 7 \ + } +// #end keyboard \ No newline at end of file diff --git a/variants/tracksenger/lcd/pins_arduino.h b/variants/tracksenger/lcd/pins_arduino.h new file mode 100644 index 000000000..5c0b529b0 --- /dev/null +++ b/variants/tracksenger/lcd/pins_arduino.h @@ -0,0 +1,80 @@ +#ifndef Pins_Arduino_h +#define Pins_Arduino_h + +#include "soc/soc_caps.h" +#include + +#define WIFI_LoRa_32_V3 true +#define DISPLAY_HEIGHT 80 +#define DISPLAY_WIDTH 160 + +#define USB_VID 0x303a +#define USB_PID 0x1001 + +#define EXTERNAL_NUM_INTERRUPTS 46 +#define NUM_DIGITAL_PINS 48 +#define NUM_ANALOG_INPUTS 20 + +static const uint8_t LED_BUILTIN = 18; +#define BUILTIN_LED LED_BUILTIN // backward compatibility +#define LED_BUILTIN LED_BUILTIN + +#define analogInputToDigitalPin(p) (((p) < 20) ? (analogChannelToDigitalPin(p)) : -1) +#define digitalPinToInterrupt(p) (((p) < 48) ? (p) : -1) +#define digitalPinHasPWM(p) (p < 46) + +static const uint8_t TX = 43; +static const uint8_t RX = 44; + +static const uint8_t SDA = 45; +static const uint8_t SCL = 46; + +static const uint8_t SS = 8; +static const uint8_t MOSI = 10; +static const uint8_t MISO = 11; +static const uint8_t SCK = 9; + +static const uint8_t A0 = 1; +static const uint8_t A1 = 2; +static const uint8_t A2 = 3; +static const uint8_t A3 = 4; +static const uint8_t A4 = 5; +static const uint8_t A5 = 6; +static const uint8_t A6 = 7; +static const uint8_t A7 = 8; +static const uint8_t A8 = 9; +static const uint8_t A9 = 10; +static const uint8_t A10 = 11; +static const uint8_t A11 = 12; +static const uint8_t A12 = 13; +static const uint8_t A13 = 14; +static const uint8_t A14 = 15; +static const uint8_t A15 = 16; +static const uint8_t A16 = 17; +static const uint8_t A17 = 18; +static const uint8_t A18 = 19; +static const uint8_t A19 = 20; + +static const uint8_t T1 = 1; +static const uint8_t T2 = 2; +static const uint8_t T3 = 3; +static const uint8_t T4 = 4; +static const uint8_t T5 = 5; +static const uint8_t T6 = 6; +static const uint8_t T7 = 7; +static const uint8_t T8 = 8; +static const uint8_t T9 = 9; +static const uint8_t T10 = 10; +static const uint8_t T11 = 11; +static const uint8_t T12 = 12; +static const uint8_t T13 = 13; +static const uint8_t T14 = 14; + +static const uint8_t Vext = 36; +static const uint8_t LED = 18; + +static const uint8_t RST_LoRa = 12; +static const uint8_t BUSY_LoRa = 13; +static const uint8_t DIO0 = 14; + +#endif /* Pins_Arduino_h */ diff --git a/variants/tracksenger/lcd/variant.h b/variants/tracksenger/lcd/variant.h new file mode 100644 index 000000000..0f3423d52 --- /dev/null +++ b/variants/tracksenger/lcd/variant.h @@ -0,0 +1,114 @@ +#define LED_PIN 18 + +#define HELTEC_TRACKER_V1_X + +// TRACKSENGER 2.8" IPS 320x240 + +// I2C +// #define I2C_SDA 42 +// #define I2C_SCL 41 +// #define HAS_SCREEN 1 +// #define USE_SSD1306 + +// Default SPI1 will be mapped to the display +#define ST7789_SDA 42 +#define ST7789_SCK 41 +#define ST7789_CS 38 +#define ST7789_RS 40 +#define ST7789_BL 21 +// P#define ST7735_BL_V05 21 /* V1.1 PCB marking */ + +#define ST7789_RESET -1 +#define ST7789_MISO -1 +#define ST7789_BUSY -1 +#define ST7789_SPI_HOST SPI3_HOST +#define ST7789_BACKLIGHT_EN 21 +#define SPI_FREQUENCY 40000000 +#define SPI_READ_FREQUENCY 16000000 +#define TFT_HEIGHT 320 +#define TFT_WIDTH 240 +#define TFT_OFFSET_X 0 +#define TFT_OFFSET_Y 0 +#define TFT_OFFSET_ROTATION 0 +#define SCREEN_ROTATE + +// ST7735S TFT LCD +// #define ST7735S 1 // there are different (sub-)versions of ST7735 +// #define ST7735_CS 38 +// #define ST7735_RS 40 // DC +// #define ST7735_SDA 42 // MOSI +// #define ST7735_SCK 41 +// #define ST7735_RESET 39 +// #define ST7735_MISO -1 +// #define ST7735_BUSY -1 +#define ST7735_BL_V05 21 /* V1.1 PCB marking */ +// #define ST7735_SPI_HOST SPI3_HOST +// #define SPI_FREQUENCY 40000000 +// #define SPI_READ_FREQUENCY 16000000 +// #define SCREEN_ROTATE +// #define TFT_HEIGHT DISPLAY_WIDTH +// #define TFT_WIDTH DISPLAY_HEIGHT +// #define TFT_OFFSET_X 26 +// #define TFT_OFFSET_Y -1 +#define SCREEN_TRANSITION_FRAMERATE 3 // fps +// #define DISPLAY_FORCE_SMALL_FONTS + +#define VEXT_ENABLE_V05 3 // active HIGH, powers the lora antenna boost +#define BUTTON_PIN 0 + +#define BATTERY_PIN 1 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage +#define ADC_CHANNEL ADC1_GPIO1_CHANNEL +#define ADC_ATTENUATION ADC_ATTEN_DB_2_5 // lower dB for high resistance voltage divider +#define ADC_MULTIPLIER 4.9 +#define ADC_CTRL 2 // active HIGH, powers the voltage divider. Only on 1.1 +#define ADC_CTRL_ENABLED HIGH + +#undef GPS_RX_PIN +#undef GPS_TX_PIN +#define GPS_RX_PIN 33 +#define GPS_TX_PIN 34 +#define PIN_GPS_RESET 35 +#define PIN_GPS_PPS 36 + +#define GPS_RESET_MODE LOW +#define GPS_UC6580 + +#define USE_SX1262 +#define LORA_DIO0 -1 // a No connect on the SX1262 module +#define LORA_RESET 12 +#define LORA_DIO1 14 // SX1262 IRQ +#define LORA_DIO2 13 // SX1262 BUSY +#define LORA_DIO3 // Not connected on PCB, but internally on the TTGO SX1262, if DIO3 is high the TXCO is enabled + +#define LORA_SCK 9 +#define LORA_MISO 11 +#define LORA_MOSI 10 +#define LORA_CS 8 + +#define SX126X_CS LORA_CS +#define SX126X_DIO1 LORA_DIO1 +#define SX126X_BUSY LORA_DIO2 +#define SX126X_RESET LORA_RESET + +#define SX126X_DIO2_AS_RF_SWITCH +#define SX126X_DIO3_TCXO_VOLTAGE 1.8 + +// Picomputer gets a white on black display +#define TFT_MESH COLOR565(0xFF, 0xFF, 0xFF) + +// keyboard changes + +#define PIN_BUZZER 43 +#define CANNED_MESSAGE_MODULE_ENABLE 1 + +#define INPUTBROKER_MATRIX_TYPE 1 + +#define KEYS_COLS \ + { \ + 44, 45, 46, 4, 5, 6 \ + } +#define KEYS_ROWS \ + { \ + 26, 37, 17, 16, 15, 7 \ + } +// #end keyboard \ No newline at end of file diff --git a/variants/tracksenger/oled/pins_arduino.h b/variants/tracksenger/oled/pins_arduino.h new file mode 100644 index 000000000..5c0b529b0 --- /dev/null +++ b/variants/tracksenger/oled/pins_arduino.h @@ -0,0 +1,80 @@ +#ifndef Pins_Arduino_h +#define Pins_Arduino_h + +#include "soc/soc_caps.h" +#include + +#define WIFI_LoRa_32_V3 true +#define DISPLAY_HEIGHT 80 +#define DISPLAY_WIDTH 160 + +#define USB_VID 0x303a +#define USB_PID 0x1001 + +#define EXTERNAL_NUM_INTERRUPTS 46 +#define NUM_DIGITAL_PINS 48 +#define NUM_ANALOG_INPUTS 20 + +static const uint8_t LED_BUILTIN = 18; +#define BUILTIN_LED LED_BUILTIN // backward compatibility +#define LED_BUILTIN LED_BUILTIN + +#define analogInputToDigitalPin(p) (((p) < 20) ? (analogChannelToDigitalPin(p)) : -1) +#define digitalPinToInterrupt(p) (((p) < 48) ? (p) : -1) +#define digitalPinHasPWM(p) (p < 46) + +static const uint8_t TX = 43; +static const uint8_t RX = 44; + +static const uint8_t SDA = 45; +static const uint8_t SCL = 46; + +static const uint8_t SS = 8; +static const uint8_t MOSI = 10; +static const uint8_t MISO = 11; +static const uint8_t SCK = 9; + +static const uint8_t A0 = 1; +static const uint8_t A1 = 2; +static const uint8_t A2 = 3; +static const uint8_t A3 = 4; +static const uint8_t A4 = 5; +static const uint8_t A5 = 6; +static const uint8_t A6 = 7; +static const uint8_t A7 = 8; +static const uint8_t A8 = 9; +static const uint8_t A9 = 10; +static const uint8_t A10 = 11; +static const uint8_t A11 = 12; +static const uint8_t A12 = 13; +static const uint8_t A13 = 14; +static const uint8_t A14 = 15; +static const uint8_t A15 = 16; +static const uint8_t A16 = 17; +static const uint8_t A17 = 18; +static const uint8_t A18 = 19; +static const uint8_t A19 = 20; + +static const uint8_t T1 = 1; +static const uint8_t T2 = 2; +static const uint8_t T3 = 3; +static const uint8_t T4 = 4; +static const uint8_t T5 = 5; +static const uint8_t T6 = 6; +static const uint8_t T7 = 7; +static const uint8_t T8 = 8; +static const uint8_t T9 = 9; +static const uint8_t T10 = 10; +static const uint8_t T11 = 11; +static const uint8_t T12 = 12; +static const uint8_t T13 = 13; +static const uint8_t T14 = 14; + +static const uint8_t Vext = 36; +static const uint8_t LED = 18; + +static const uint8_t RST_LoRa = 12; +static const uint8_t BUSY_LoRa = 13; +static const uint8_t DIO0 = 14; + +#endif /* Pins_Arduino_h */ diff --git a/variants/tracksenger/oled/variant.h b/variants/tracksenger/oled/variant.h new file mode 100644 index 000000000..d6bacf139 --- /dev/null +++ b/variants/tracksenger/oled/variant.h @@ -0,0 +1,92 @@ +#define LED_PIN 18 + +#define HELTEC_TRACKER_V1_X + +// TRACKSENGER 2.42" I2C OLED + +// I2C +#define I2C_SDA 42 +#define I2C_SCL 41 +#define HAS_SCREEN 1 +#define USE_SSD1306 + +// ST7735S TFT LCD +// #define ST7735S 1 // there are different (sub-)versions of ST7735 +// #define ST7735_CS 38 +// #define ST7735_RS 40 // DC +// #define ST7735_SDA 42 // MOSI +// #define ST7735_SCK 41 +// #define ST7735_RESET 39 +// #define ST7735_MISO -1 +// #define ST7735_BUSY -1 +#define ST7735_BL_V05 21 /* V1.1 PCB marking */ +// #define ST7735_SPI_HOST SPI3_HOST +// #define SPI_FREQUENCY 40000000 +// #define SPI_READ_FREQUENCY 16000000 +// #define SCREEN_ROTATE +// #define TFT_HEIGHT DISPLAY_WIDTH +// #define TFT_WIDTH DISPLAY_HEIGHT +// #define TFT_OFFSET_X 26 +// #define TFT_OFFSET_Y -1 +#define SCREEN_TRANSITION_FRAMERATE 3 // fps +// #define DISPLAY_FORCE_SMALL_FONTS + +#define VEXT_ENABLE_V05 3 // active HIGH, powers the lora antenna boost +#define BUTTON_PIN 0 + +#define BATTERY_PIN 1 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage +#define ADC_CHANNEL ADC1_GPIO1_CHANNEL +#define ADC_ATTENUATION ADC_ATTEN_DB_2_5 // lower dB for high resistance voltage divider +#define ADC_MULTIPLIER 4.9 +#define ADC_CTRL 2 // active HIGH, powers the voltage divider. Only on 1.1 +#define ADC_CTRL_ENABLED HIGH + +#undef GPS_RX_PIN +#undef GPS_TX_PIN +#define GPS_RX_PIN 33 +#define GPS_TX_PIN 34 +#define PIN_GPS_RESET 35 +#define PIN_GPS_PPS 36 + +#define GPS_RESET_MODE LOW +#define GPS_UC6580 + +#define USE_SX1262 +#define LORA_DIO0 -1 // a No connect on the SX1262 module +#define LORA_RESET 12 +#define LORA_DIO1 14 // SX1262 IRQ +#define LORA_DIO2 13 // SX1262 BUSY +#define LORA_DIO3 // Not connected on PCB, but internally on the TTGO SX1262, if DIO3 is high the TXCO is enabled + +#define LORA_SCK 9 +#define LORA_MISO 11 +#define LORA_MOSI 10 +#define LORA_CS 8 + +#define SX126X_CS LORA_CS +#define SX126X_DIO1 LORA_DIO1 +#define SX126X_BUSY LORA_DIO2 +#define SX126X_RESET LORA_RESET + +#define SX126X_DIO2_AS_RF_SWITCH +#define SX126X_DIO3_TCXO_VOLTAGE 1.8 + +// Picomputer gets a white on black display +#define TFT_MESH COLOR565(0xFF, 0xFF, 0xFF) + +// keyboard changes + +#define PIN_BUZZER 43 +#define CANNED_MESSAGE_MODULE_ENABLE 1 + +#define INPUTBROKER_MATRIX_TYPE 1 + +#define KEYS_COLS \ + { \ + 44, 45, 46, 4, 5, 6 \ + } +#define KEYS_ROWS \ + { \ + 26, 37, 17, 16, 15, 7 \ + } +// #end keyboard \ No newline at end of file diff --git a/variants/tracksenger/platformio.ini b/variants/tracksenger/platformio.ini new file mode 100644 index 000000000..d3e31264f --- /dev/null +++ b/variants/tracksenger/platformio.ini @@ -0,0 +1,40 @@ +[env:tracksenger] +extends = esp32s3_base +board = heltec_wireless_tracker +upload_protocol = esp-builtin + +build_flags = + ${esp32s3_base.build_flags} -I variants/tracksenger/internal + -D HELTEC_TRACKER_V1_1 + -D GPS_POWER_TOGGLE ; comment this line to disable triple press function on the user button to turn off gps entirely. + ;-D DEBUG_DISABLED ; uncomment this line to disable DEBUG output + +lib_deps = + ${esp32s3_base.lib_deps} + lovyan03/LovyanGFX@^1.1.8 + +[env:tracksenger-lcd] +extends = esp32s3_base +board = heltec_wireless_tracker +upload_protocol = esp-builtin + +build_flags = + ${esp32s3_base.build_flags} -I variants/tracksenger/lcd + -D HELTEC_TRACKER_V1_1 + -D GPS_POWER_TOGGLE ; comment this line to disable triple press function on the user button to turn off gps entirely. + ;-D DEBUG_DISABLED ; uncomment this line to disable DEBUG output + +lib_deps = + ${esp32s3_base.lib_deps} + lovyan03/LovyanGFX@^1.1.8 + +[env:tracksenger-oled] +extends = esp32s3_base +board = heltec_wireless_tracker +upload_protocol = esp-builtin + +build_flags = + ${esp32s3_base.build_flags} -I variants/tracksenger/oled + -D HELTEC_TRACKER_V1_1 + -D GPS_POWER_TOGGLE ; comment this line to disable triple press function on the user button to turn off gps entirely. + ;-D DEBUG_DISABLED ; uncomment this line to disable DEBUG output