Remove unused nrf52 tests

bin/qspi-flash-test.sh

@@ -1,8 +0,0 @@
-#!/usr/bin/env bash
-
-# You probably don't need this - it is a basic test of the serial flash on the TTGO eink board
-
-nrfjprog --qspiini nrf52/ttgo_eink_qpsi.ini --qspieraseall
-nrfjprog --qspiini nrf52/ttgo_eink_qpsi.ini --memwr 0x12000000 --val 0xdeadbeef --verify
-nrfjprog --qspiini nrf52/ttgo_eink_qpsi.ini --readqspi spi.hex
-objdump -s spi.hex | less

nrf52/ttgo_eink_qpsi.ini

@@ -1,62 +0,0 @@
-; nrfjprog.exe configuration file.
-
-; Note: QSPI flash is mapped into memory at address 0x12000000
-
-[DEFAULT_CONFIGURATION]
-; Define the capacity of the flash memory device in bytes. Set to 0 if no external memory device is present in your board.
-; MX25R1635F is 16Mbit/2Mbyte
-MemSize = 0x200000
-
-; Define the desired ReadMode. Valid options are FASTREAD, READ2O, READ2IO, READ4O and READ4IO
-ReadMode = READ4IO
-
-; Define the desired WriteMode. Valid options are PP, PP2O, PP4O and PP4IO
-WriteMode = PP4IO
-
-; Define the desired AddressMode. Valid options are BIT24 and BIT32
-AddressMode = BIT24
-
-; Define the desired Frequency. Valid options are M2, M4, M8, M16 and M32
-Frequency = M16
-
-; Define the desired SPI mode. Valid options are MODE0 and MODE3
-SpiMode = MODE0
-
-; Define the desired SckDelay. Valid options are in the range 0 to 255
-SckDelay = 0x80
-
-; Define the desired IO level for DIO2 and DIO3 during a custom instruction. Valid options are LEVEL_HIGH and LEVEL_LOW
-CustomInstructionIO2Level = LEVEL_LOW
-CustomInstructionIO3Level = LEVEL_HIGH
-
-; Define the assigned pins for the QSPI peripheral. Valid options are those existing in your device
-CSNPin = 15
-CSNPort = 1
-SCKPin = 14
-SCKPort = 1
-DIO0Pin = 12
-DIO0Port = 1
-DIO1Pin = 13
-DIO1Port = 1
-DIO2Pin = 7
-DIO2Port = 0
-DIO3Pin = 5
-DIO3Port = 0
-
-; Define the Index of the Write In Progress (WIP) bit in the status register. Valid options are in the range of 0 to 7.
-WIPIndex = 0
-
-; Define page size for commands. Valid sizes are PAGE256 and PAGE512.
-PPSize = PAGE256
-
-; Custom instructions to send to the external memory after initialization. Format is instruction code plus data to send in between optional brakets. 
-; These instructions will be executed each time the qspi peripheral is initiated by nrfjprog. 
-; To improve execution speed on consecutive interations with QSPI, you can run nrfjprog once with custom initialization, and then comment out the lines below.
-; Numbers can be given in decimal, hex (starting with either 0x or 0X) and binary (starting with either 0b or 0B) formats. 
-; The custom instructions will be executed in the order found. 
-
-; For MX25R1635F on TTGO board, only two data lines are connected
-; This example includes two commands, first a WREN (WRite ENable) and then a WRSR (WRite Satus Register) enabling Quad Operation and the High Performance
-; mode.  For normal operation you might want low power mode instead.
-InitializationCustomInstruction =  0x06
-InitializationCustomInstruction =  0x01, [0x40, 0, 0x2]

nrf52/ttgo_eink_qpsi0.1.ini

@@ -1,69 +0,0 @@
-; nrfjprog.exe configuration file.
-
-; Note: QSPI flash is mapped into memory at address 0x12000000
-
-[DEFAULT_CONFIGURATION]
-; Define the capacity of the flash memory device in bytes. Set to 0 if no external memory device is present in your board.
-; MX25R1635F is 16Mbit/2Mbyte
-MemSize = 0x200000
-
-; Define the desired ReadMode. Valid options are FASTREAD, READ2O, READ2IO, READ4O and READ4IO
-ReadMode = READ2IO
-
-; Define the desired WriteMode. Valid options are PP, PP2O, PP4O and PP4IO
-WriteMode = PP
-
-; Define the desired AddressMode. Valid options are BIT24 and BIT32
-AddressMode = BIT24
-
-; Define the desired Frequency. Valid options are M2, M4, M8, M16 and M32
-Frequency = M16
-
-; Define the desired SPI mode. Valid options are MODE0 and MODE3
-SpiMode = MODE0
-
-; Define the desired SckDelay. Valid options are in the range 0 to 255
-SckDelay = 0x80
-
-; Define the desired IO level for DIO2 and DIO3 during a custom instruction. Valid options are LEVEL_HIGH and LEVEL_LOW
-CustomInstructionIO2Level = LEVEL_LOW
-CustomInstructionIO3Level = LEVEL_HIGH
-
-; Define the assigned pins for the QSPI peripheral. Valid options are those existing in your device
-CSNPin = 15
-CSNPort = 1
-SCKPin = 14
-SCKPort = 1
-DIO0Pin = 12
-DIO0Port = 1
-DIO1Pin = 13
-DIO1Port = 1
-
-;These two pins are not connected, but we must name something
-DIO2Pin = 3
-DIO2Port = 1
-DIO3Pin = 5
-DIO3Port = 1
-
-; Define the Index of the Write In Progress (WIP) bit in the status register. Valid options are in the range of 0 to 7.
-WIPIndex = 0
-
-; Define page size for commands. Valid sizes are PAGE256 and PAGE512.
-PPSize = PAGE256
-
-; Custom instructions to send to the external memory after initialization. Format is instruction code plus data to send in between optional brakets. 
-; These instructions will be executed each time the qspi peripheral is initiated by nrfjprog. 
-; To improve execution speed on consecutive interations with QSPI, you can run nrfjprog once with custom initialization, and then comment out the lines below.
-; Numbers can be given in decimal, hex (starting with either 0x or 0X) and binary (starting with either 0b or 0B) formats. 
-; The custom instructions will be executed in the order found. 
-
-; This example includes two commands, first a WREN (WRite ENable) and then a WRSR (WRite Satus Register) enabling the Quad Operation and the High Performance
-; mode for the MX25R6435F memory present in the nRF52840 DK.
-;InitializationCustomInstruction =  0x06
-;InitializationCustomInstruction =  0x01, [0x40, 0, 0x2]
-
-; For MX25R1635F on TTGO board, only two data lines are connected
-; This example includes two commands, first a WREN (WRite ENable) and then a WRSR (WRite Satus Register) disabling Quad Operation and the High Performance
-; mode.  For normal operation you might want low power mode instead.
-InitializationCustomInstruction =  0x06
-InitializationCustomInstruction =  0x01, [0x00, 0, 0x2]