meshtastic-firmware/bin/config-dist.yaml

### Define your devices here using Broadcom pin numbering
### Uncomment the block that corresponds to your hardware
### Including the "Module:" line!
---
Lora:
#  Module: sx1262  # Waveshare SX126X XXXM
#  DIO2_AS_RF_SWITCH: true
#  CS: 21
#  IRQ: 16
#  Busy: 20
#  Reset: 18

#  Module: sx1262  # Waveshare SX1302 LISTEN ONLY AT THIS TIME!
#  CS: 7
#  IRQ: 17
#  Reset: 22

#  Module: sx1262  # pinedio
#  CS: 0
#  IRQ: 10
#  Busy: 11
#  spidev: spidev0.1

#  Module: RF95  # Adafruit RFM9x
#  Reset: 25
#  CS: 7
#  IRQ: 22
#  Busy: 23

#  Module: RF95  # Elecrow Lora RFM95 IOT https://www.elecrow.com/lora-rfm95-iot-board-for-rpi.html
#  Reset: 22
#  CS: 7
#  IRQ: 25

#  Module: sx1280  # SX1280
#  CS: 21
#  IRQ: 16
#  Busy: 20
#  Reset: 18

#  Module: sx1268  # SX1268-based modules, tested with Ebyte E22 400M33S
#  CS: 21
#  IRQ: 16
#  Busy: 20
#  Reset: 18
#  TXen: 6
#  RXen: 12
#  DIO3_TCXO_VOLTAGE: true

#  DIO3_TCXO_VOLTAGE: true  # the Waveshare Core1262 and others are known to need this setting

#  TXen: x  # TX and RX enable pins
#  RXen: x

#  ch341_quirk: true # Uncomment this to use the chunked SPI transfer that seems to fix the ch341

### Set gpio chip to use in /dev/. Defaults to 0.
### Notably the Raspberry Pi 5 puts the GPIO header on gpiochip4
#  gpiochip: 4

### Specify the SPI device to use in /dev/. Defaults to spidev0.0
### Some devices, like the pinedio, may require spidev0.1 as a workaround.
#  spidev: spidev0.0

### Define GPIO buttons here:

GPIO:
#  User: 6

### Define GPS

GPS:
#  SerialPath: /dev/ttyS0

### Specify I2C device, or leave blank for none

I2C:
#  I2CDevice: /dev/i2c-1

### Set up SPI displays here. Note that I2C displays are generally auto-detected.

Display:

### Waveshare 2.8inch RPi LCD
#  Panel: ST7789
#  CS: 8
#  DC: 22        # Data/Command pin
#  Backlight: 18
#  Width: 240
#  Height: 320
#  Reset: 27
#  Rotate: true
#  Invert: true

### Waveshare 1.44inch LCD HAT
#  Panel: ST7735S
#  CS: 8         #Chip Select
#  DC: 25        # Data/Command pin
#  Backlight: 24
#  Width: 128
#  Height: 128
#  Reset: 27
#  OffsetX: 0
#  OffsetY: 0

### Adafruit PiTFT 2.8 TFT+Touchscreen
#  Panel: ILI9341
#  CS: 8
#  DC: 25
#  Width: 240
#  Height: 320
#  Rotate: true

Touchscreen:
### Note, at least for now, the touchscreen must have a CS pin defined, even if you let Linux manage the CS switching.

#  Module: STMPE610 # Option 1 for Adafruit PiTFT 2.8
#  CS: 7
#  IRQ: 24

#  Module: FT5x06 # Option 2 for Adafruit PiTFT 2.8
#  IRQ: 24
#  I2CAddr: 0x38

#  Module: XPT2046 # Waveshare 2.8inch
#  CS: 7
#  IRQ: 17

### Configure device for direct keyboard input

Input:
#  KeyboardDevice: /dev/input/by-id/usb-_Raspberry_Pi_Internal_Keyboard-event-kbd

###

Logging:
  LogLevel: info # debug, info, warn, error

Webserver:
#  Port: 443 # Port for Webserver & Webservices
#  RootPath: /usr/share/doc/meshtasticd/web # Root Dir of WebServer

General:
  MaxNodes: 200