kopia lustrzana https://github.com/jbruce12000/kiln-controller
removing config.py.EXAMPLE and docs describing it
jbruce12000
rodzic
8ab564c72b
commit
dab1c45b7f
|
|
@ -84,11 +84,9 @@ If you want to deploy the code on a PI for production:
|
|||
|
||||
## Configuration
|
||||
|
||||
All parameters are defined in config.py, just copy the example and review/change to your mind's content.
|
||||
All parameters are defined in config.py, review/change to your mind's content.
|
||||
|
||||
$ cp config.py.EXAMPLE config.py
|
||||
|
||||
You should change, test, and verify PID parameters in config.py. Here is a [PID Tuning Guide](https://github.com/jbruce12000/kiln-controller/blob/master/docs/pid_tuning.md).
|
||||
You should change, test, and verify PID parameters in config.py. Here is a [PID Tuning Guide](https://github.com/jbruce12000/kiln-controller/blob/master/docs/pid_tuning.md). There is also an [autotuner](https://github.com/jbruce12000/kiln-controller/blob/master/docs/ziegler_tuning.md). Be patient with tuning. No tuning is perfect across a wide temperature range.
|
||||
|
||||
You may want to change the configuration parameter **sensor_time_wait**. It's the duty cycle for the entire system. It's set to two seconds by default which means that a decision is made every 2s about whether to turn on relay[s] and for how long. If you use mechanical relays, you may want to increase this. At 2s, my SSR switches 11,000 times in 13 hours.
|
||||
|
||||
|
|
|
|||
|
|
@ -1,150 +0,0 @@
|
|||
import logging
|
||||
|
||||
# uncomment this if using MAX-31856
|
||||
#from lib.max31856 import MAX31856
|
||||
|
||||
########################################################################
|
||||
#
|
||||
# General options
|
||||
|
||||
### Logging
|
||||
log_level = logging.INFO
|
||||
log_format = '%(asctime)s %(levelname)s %(name)s: %(message)s'
|
||||
|
||||
### Server
|
||||
listening_ip = "0.0.0.0"
|
||||
listening_port = 8081
|
||||
|
||||
### Cost Estimate
|
||||
kwh_rate = 0.1319 # Rate in currency_type to calculate cost to run job
|
||||
currency_type = "$" # Currency Symbol to show when calculating cost to run job
|
||||
|
||||
########################################################################
|
||||
#
|
||||
# GPIO Setup (BCM SoC Numbering Schema)
|
||||
#
|
||||
# Check the RasPi docs to see where these GPIOs are
|
||||
# connected on the P1 header for your board type/rev.
|
||||
# These were tested on a Pi B Rev2 but of course you
|
||||
# can use whichever GPIO you prefer/have available.
|
||||
|
||||
### Outputs
|
||||
gpio_heat = 23 # Switches zero-cross solid-state-relay
|
||||
|
||||
### Thermocouple Adapter selection:
|
||||
# max31855 - bitbang SPI interface
|
||||
# max31856 - bitbang SPI interface. must specify thermocouple_type.
|
||||
max31855 = 1
|
||||
max31856 = 0
|
||||
# see lib/max31856.py for other thermocouple_type, only applies to max31856
|
||||
# uncomment this if using MAX-31856
|
||||
#thermocouple_type = MAX31856.MAX31856_S_TYPE
|
||||
|
||||
### Thermocouple Connection (using bitbang interfaces)
|
||||
gpio_sensor_cs = 27
|
||||
gpio_sensor_clock = 22
|
||||
gpio_sensor_data = 17
|
||||
gpio_sensor_di = 10 # only used with max31856
|
||||
|
||||
########################################################################
|
||||
#
|
||||
# duty cycle of the entire system in seconds
|
||||
#
|
||||
# Every N seconds a decision is made about switching the relay[s]
|
||||
# on & off and for how long. The thermocouple is read
|
||||
# temperature_average_samples times during and the average value is used.
|
||||
sensor_time_wait = 2
|
||||
|
||||
|
||||
########################################################################
|
||||
#
|
||||
# PID parameters
|
||||
#
|
||||
# These parameters control kiln temperature change. These settings work
|
||||
# well with the simulated oven. You must tune them to work well with
|
||||
# your specific kiln. Note that the integral pid_ki is
|
||||
# inverted so that a smaller number means more integral action.
|
||||
pid_kp = 25 # Proportional
|
||||
pid_ki = 200 # Integral
|
||||
pid_kd = 200 # Derivative
|
||||
|
||||
|
||||
########################################################################
|
||||
#
|
||||
# Initial heating and Integral Windup
|
||||
#
|
||||
# During initial heating, if the temperature is constantly under the
|
||||
# setpoint,large amounts of Integral can accumulate. This accumulation
|
||||
# causes the kiln to run above the setpoint for potentially a long
|
||||
# period of time. These settings allow integral accumulation only when
|
||||
# the temperature is close to the setpoint. This applies only to the integral.
|
||||
stop_integral_windup = True
|
||||
|
||||
########################################################################
|
||||
#
|
||||
# Simulation parameters
|
||||
simulate = True
|
||||
sim_t_env = 60.0 # deg C
|
||||
sim_c_heat = 100.0 # J/K heat capacity of heat element
|
||||
sim_c_oven = 5000.0 # J/K heat capacity of oven
|
||||
sim_p_heat = 5450.0 # W heating power of oven
|
||||
sim_R_o_nocool = 0.1 # K/W thermal resistance oven -> environment
|
||||
sim_R_o_cool = 0.05 # K/W " with cooling
|
||||
sim_R_ho_noair = 0.1 # K/W thermal resistance heat element -> oven
|
||||
sim_R_ho_air = 0.05 # K/W " with internal air circulation
|
||||
|
||||
|
||||
########################################################################
|
||||
#
|
||||
# Time and Temperature parameters
|
||||
#
|
||||
# If you change the temp_scale, all settings in this file are assumed to
|
||||
# be in that scale.
|
||||
|
||||
temp_scale = "f" # c = Celsius | f = Fahrenheit - Unit to display
|
||||
time_scale_slope = "h" # s = Seconds | m = Minutes | h = Hours - Slope displayed in temp_scale per time_scale_slope
|
||||
time_scale_profile = "m" # s = Seconds | m = Minutes | h = Hours - Enter and view target time in time_scale_profile
|
||||
|
||||
# emergency shutoff the profile if this temp is reached or exceeded.
|
||||
# This just shuts off the profile. If your SSR is working, your kiln will
|
||||
# naturally cool off. If your SSR has failed/shorted/closed circuit, this
|
||||
# means your kiln receives full power until your house burns down.
|
||||
# this should not replace you watching your kiln or use of a kiln-sitter
|
||||
emergency_shutoff_temp = 2264 #cone 7
|
||||
|
||||
# If the kiln cannot heat or cool fast enough and is off by more than
|
||||
# kiln_must_catch_up_max_error the entire schedule is shifted until
|
||||
# the desired temperature is reached. If your kiln cannot attain the
|
||||
# wanted temperature, the schedule will run forever. This is often used
|
||||
# for heating as fast as possible in a section of a kiln schedule/profile.
|
||||
kiln_must_catch_up = True
|
||||
kiln_must_catch_up_max_error = 5 #degrees
|
||||
|
||||
# thermocouple offset
|
||||
# If you put your thermocouple in ice water and it reads 36F, you can
|
||||
# set set this offset to -4 to compensate. This probably means you have a
|
||||
# cheap thermocouple. Invest in a better thermocouple.
|
||||
thermocouple_offset=0
|
||||
|
||||
# some kilns/thermocouples start erroneously reporting "short"
|
||||
# errors at higher temperatures due to plasma forming in the kiln.
|
||||
# Set this to False to ignore these errors and assume the temperature
|
||||
# reading was correct anyway
|
||||
honour_theromocouple_short_errors = False
|
||||
|
||||
# number of samples of temperature to average.
|
||||
# If you suffer from the high temperature kiln issue and have set
|
||||
# honour_theromocouple_short_errors to False,
|
||||
# you will likely need to increase this (eg I use 40)
|
||||
temperature_average_samples = 40
|
||||
|
||||
# Thermocouple AC frequency filtering - set to True if in a 50Hz locale, else leave at False for 60Hz locale
|
||||
ac_freq_50hz = False
|
||||
|
||||
# There are all kinds of emergencies that can happen including:
|
||||
# - temperature is too high (emergency_shutoff_temp exceeded)
|
||||
# - lost connection to thermocouple
|
||||
# - unknown error with thermocouple
|
||||
# - too many errors in a short period from thermocouple
|
||||
# and some people just want to ignore all of that and just log the emergencies but do not quit
|
||||
ignore_emergencies = False
|
||||
Ładowanie…
Reference in New Issue