kopia lustrzana https://github.com/k3ng/k3ng_cw_keyer
64 wiersze
5.0 KiB
C
Executable File
64 wiersze
5.0 KiB
C
Executable File
// compile time features and options - comment or uncomment to add or delete features
|
|
// FEATURES add more bytes to the compiled binary, OPTIONS change code behavior
|
|
|
|
// features & options for TinyKeyer by OK1RR
|
|
|
|
#define FEATURE_COMMAND_BUTTONS
|
|
//#define FEATURE_COMMAND_LINE_INTERFACE // (this no longer requires FEATURE_SERIAL)
|
|
#define FEATURE_MEMORIES
|
|
//#define FEATURE_MEMORY_MACROS
|
|
#define FEATURE_WINKEY_EMULATION // disabling Automatic Software Reset is highly recommended (see documentation) (this no longer requires FEATURE_SERIAL)
|
|
//#define FEATURE_POTENTIOMETER // do not enable unless you have a potentiometer connected, otherwise noise will falsely trigger wpm changes
|
|
//#define FEATURE_SIDETONE_SWITCH // adds switch control for the sidetone output. requires an external toggle switch (assigned to an arduino pin - see keyer_pin_settings.h).
|
|
//#define FEATURE_DEAD_OP_WATCHDOG
|
|
#define FEATURE_AUTOSPACE
|
|
//#define FEATURE_FARNSWORTH
|
|
//#define FEATURE_DL2SBA_BANKSWITCH // Switch memory banks feature as described here: http://dl2sba.com/index.php?option=com_content&view=article&id=131:nanokeyer&catid=15:shack&Itemid=27#english
|
|
//#define FEATURE_SLEEP // go to sleep after x minutes to conserve battery power
|
|
#define FEATURE_ROTARY_ENCODER // rotary encoder speed control
|
|
//#define FEATURE_CMOS_SUPER_KEYER_IAMBIC_B_TIMING
|
|
//#define FEATURE_DIT_DAH_BUFFER_CONTROL
|
|
//#define FEATURE_HI_PRECISION_LOOP_TIMING
|
|
//#define FEATURE_ALPHABET_SEND_PRACTICE // enables command mode S command - created by Ryan, KC2ZWM
|
|
//#define FEATURE_PTT_INTERLOCK
|
|
//#define FEATURE_QLF
|
|
//#define FEATURE_EEPROM_E24C1024
|
|
//#define FEATURE_STRAIGHT_KEY
|
|
//#define FEATURE_DYNAMIC_DAH_TO_DIT_RATIO
|
|
//#define FEATURE_AMERICAN_MORSE
|
|
// #define FEATURE_4x4_KEYPAD // code contributed by Jack, W0XR - documentation: https://github.com/k3ng/k3ng_cw_keyer/wiki/380-Feature:-Keypad
|
|
// #define FEATURE_3x4_KEYPAD // code contributed by Jack, W0XR - documentation: https://github.com/k3ng/k3ng_cw_keyer/wiki/380-Feature:-Keypad
|
|
|
|
#define OPTION_SUPPRESS_SERIAL_BOOT_MSG
|
|
#define OPTION_INCLUDE_PTT_TAIL_FOR_MANUAL_SENDING
|
|
#define OPTION_EXCLUDE_PTT_HANG_TIME_FOR_MANUAL_SENDING
|
|
//#define OPTION_SERIAL_PORT_DEFAULT_WINKEY_EMULATION // Use when activating both FEATURE_WINKEY_EMULATION and FEATURE_COMMAND_LINE_INTERFACE simultaneously. This will make Winkey emulation be the default at boot up; hold command button down at boot up to activate CLI mode
|
|
//#define OPTION_WINKEY_DISCARD_BYTES_AT_STARTUP // if ASR is not disabled, you may need this to discard errant serial port bytes at startup
|
|
//#define OPTION_WINKEY_STRICT_EEPROM_WRITES_MAY_WEAR_OUT_EEPROM // with this activated the unit will write non-volatile settings to EEPROM when set by Winkey commands
|
|
#define OPTION_WINKEY_SEND_WORDSPACE_AT_END_OF_BUFFER
|
|
#define OPTION_WINKEY_STRICT_HOST_OPEN // require an admin host open Winkey command before doing any other commands
|
|
#define OPTION_WINKEY_2_SUPPORT // comment out to revert to Winkey version 1 emulation
|
|
#define OPTION_WINKEY_INTERRUPTS_MEMORY_REPEAT
|
|
//#define OPTION_WINKEY_UCXLOG_9600_BAUD // use this only with UCXLog configured for Winkey 9600 baud mode
|
|
#define OPTION_WINKEY_2_HOST_CLOSE_NO_SERIAL_PORT_RESET // activate this when using Winkey 2 emulation and Win-Test
|
|
//#define OPTION_WINKEY_FREQUENT_STATUS_REPORT // activate this to make Winkey emulation play better with RUMlog and RUMped
|
|
//#define OPTION_WINKEY_IGNORE_LOWERCASE // Enable for typical K1EL Winkeyer behavior (use for SkookumLogger version 1.10.14 and prior to workaround bug)
|
|
#define OPTION_PROG_MEM_TRIM_TRAILING_SPACES // trim trailing spaces from memory when programming in command mode
|
|
#define OPTION_DIT_PADDLE_NO_SEND_ON_MEM_RPT // this makes dit paddle memory interruption a little smoother
|
|
//#define OPTION_N1MM_WINKEY_TAB_BUG_WORKAROUND // enable this to ignore the TAB key in the Send CW window (this breaks SO2R functionality in N1MM)
|
|
//#define OPTION_WATCHDOG_TIMER // this enables a four second ATmega48/88/168/328 watchdog timer; use for unattended/remote operation only
|
|
//#define OPTION_NON_ENGLISH_EXTENSIONS // add support for additional CW characters (i.e. À, Å, Þ, etc.)
|
|
//#define OPTION_KEEP_PTT_KEYED_WHEN_CHARS_BUFFERED // this option keeps PTT high if there are characters buffered from the keyboard, the serial interface, or Winkey
|
|
//#define OPTION_UNKNOWN_CHARACTER_ERROR_TONE
|
|
//#define OPTION_DO_NOT_SAY_HI
|
|
#define OPTION_SAVE_MEMORY_NANOKEYER
|
|
//#define OPTION_INVERT_PADDLE_PIN_LOGIC
|
|
//#define OPTION_DIT_DAH_BUFFERS_OFF_BY_DEFAULT_FOR_FEATURE_DIT_DAH_BUFFER_CONTROL
|
|
//#define OPTION_RUSSIAN_LANGUAGE_SEND_CLI // Russian language CLI sending support (contributed by Павел Бирюков, UA1AQC)
|
|
#define OPTION_DO_NOT_SEND_UNKNOWN_CHAR_QUESTION
|
|
//#define OPTION_CMOS_SUPER_KEYER_IAMBIC_B_TIMING_ON_BY_DEFAULT
|
|
|
|
// #define OPTION_WORDSWORTH_CZECH
|
|
// #define OPTION_WORDSWORTH_DEUTSCH
|
|
// #define OPTION_WORDSWORTH_NORSK
|