kopia lustrzana https://github.com/k3ng/k3ng_cw_keyer
103 wiersze
8.0 KiB
C
Executable File
103 wiersze
8.0 KiB
C
Executable File
// This file is for the Yaacwk interface http://i1cra.briata.org/yaacwk/
|
|
// YAACWK stands for Yet Another Arduino CW Keyer, it's based on AtMega 644p
|
|
// see http://i1cra.briata.org/yaacwk/ for more info
|
|
|
|
// compile time features and options - comment or uncomment to add or delete features
|
|
// FEATURES add more bytes to the compiled binary, OPTIONS change code behavior
|
|
|
|
#define FEATURE_COMMAND_BUTTONS
|
|
#define FEATURE_COMMAND_LINE_INTERFACE // (this no longer requires FEATURE_SERIAL)
|
|
#define FEATURE_MEMORIES
|
|
//#define FEATURE_MEMORY_MACROS
|
|
#define FEATURE_WINKEY_EMULATION // disabling Automatic Software Reset is highly recommended (see documentation) (this no longer requires FEATURE_SERIAL)
|
|
//#define FEATURE_BEACON
|
|
//#define FEATURE_TRAINING_COMMAND_LINE_INTERFACE
|
|
#define FEATURE_POTENTIOMETER // do not enable unless you have a potentiometer connected, otherwise noise will falsely trigger wpm changes
|
|
//#define FEATURE_SIDETONE_SWITCH // adds switch control for the sidetone output. requires an external toggle switch (assigned to an arduino pin - see keyer_pin_settings.h).
|
|
//#define FEATURE_SERIAL_HELP
|
|
//#define FEATURE_HELL
|
|
#define FEATURE_PS2_KEYBOARD // Use a PS2 keyboard to send code - Change keyboard layout (non-US) in K3NG_PS2Keyboard.h. Additional options below.
|
|
//#define FEATURE_USB_KEYBOARD // Use a USB keyboard to send code - Uncomment three lines in k3ng_keyer.ino (search for note_usb_uncomment_lines)
|
|
//#define FEATURE_DEAD_OP_WATCHDOG
|
|
//#define FEATURE_AUTOSPACE
|
|
//#define FEATURE_FARNSWORTH
|
|
//#define FEATURE_DL2SBA_BANKSWITCH // Switch memory banks feature as described here: http://dl2sba.com/index.php?option=com_content&view=article&id=131:nanokeyer&catid=15:shack&Itemid=27#english
|
|
#define FEATURE_LCD_4BIT // classic LCD disidefplay using 4 I/O lines
|
|
//#define FEATURE_LCD_ADAFRUIT_I2C // Adafruit I2C LCD display using MCP23017 at addr 0x20
|
|
//#define FEATURE_LCD_YDv1 // YourDuino I2C LCD display with old LCM 1602 V1 ic
|
|
//#define FEATURE_LCD_FABO_PCF8574 // https://github.com/FaBoPlatform/FaBoLCD-PCF8574-Library
|
|
#define FEATURE_CW_DECODER
|
|
//#define FEATURE_SLEEP // go to sleep after x minutes to conserve battery power
|
|
//#define FEATURE_ROTARY_ENCODER // rotary encoder speed control
|
|
//#define FEATURE_CMOS_SUPER_KEYER_IAMBIC_B_TIMING
|
|
//#define FEATURE_USB_MOUSE // Uncomment three lines in k3ng_keyer.ino (search for note_usb_uncomment_lines)
|
|
//#define FEATURE_CAPACITIVE_PADDLE_PINS // remove the bypass capacitors on the paddle_left and paddle_right lines when using capactive paddles
|
|
//#define FEATURE_LED_RING // Mayhew Labs Led Ring support
|
|
#define FEATURE_ALPHABET_SEND_PRACTICE // enables command mode S command - created by Ryan, KC2ZWM
|
|
//#define FEATURE_COMMAND_MODE_PROGRESSIVE_5_CHAR_ECHO_PRACTICE // enables command mode U
|
|
//#define FEATURE_PTT_INTERLOCK
|
|
//#define FEATURE_QLF
|
|
//#define FEATURE_EEPROM_E24C1024
|
|
//#define FEATURE_STRAIGHT_KEY
|
|
//#define FEATURE_DYNAMIC_DAH_TO_DIT_RATIO
|
|
//#define FEATURE_PADDLE_ECHO
|
|
//#define FEATURE_STRAIGHT_KEY_ECHO
|
|
//#define FEATURE_AMERICAN_MORSE
|
|
//#define FEATURE_4x4_KEYPAD // code contributed by Jack, W0XR - documentation: https://github.com/k3ng/k3ng_cw_keyer/wiki/380-Feature:-Keypad
|
|
//#define FEATURE_3x4_KEYPAD // code contributed by Jack, W0XR - documentation: https://github.com/k3ng/k3ng_cw_keyer/wiki/380-Feature:-Keypad
|
|
//#define FEATURE_SEQUENCER
|
|
|
|
#define FEATURE_COMMAND_LINE_INTERFACE_ON_SECONDARY_PORT // Activate the Command Line interface on the secondary serial port
|
|
#define OPTION_PRIMARY_SERIAL_PORT_DEFAULT_WINKEY_EMULATION // Use when activating both FEATURE_WINKEY_EMULATION and FEATURE_COMMAND_LINE_INTERFACE
|
|
// simultaneously. This will make Winkey emulation be the default at boot up;
|
|
// hold command button down at boot up to activate CLI mode
|
|
|
|
//#define OPTION_SUPPRESS_SERIAL_BOOT_MSG
|
|
#define OPTION_INCLUDE_PTT_TAIL_FOR_MANUAL_SENDING
|
|
#define OPTION_EXCLUDE_PTT_HANG_TIME_FOR_MANUAL_SENDING
|
|
#define OPTION_SERIAL_PORT_DEFAULT_WINKEY_EMULATION // Use when activating both FEATURE_WINKEY_EMULATION and FEATURE_COMMAND_LINE_INTERFACE simultaneously. This will make Winkey emulation be the default at boot up; hold command button down at boot up to activate CLI mode
|
|
//#define OPTION_WINKEY_DISCARD_BYTES_AT_STARTUP // if ASR is not disabled, you may need this to discard errant serial port bytes at startup
|
|
//#define OPTION_WINKEY_STRICT_EEPROM_WRITES_MAY_WEAR_OUT_EEPROM // with this activated the unit will write non-volatile settings to EEPROM when set by Winkey commands
|
|
//#define OPTION_WINKEY_SEND_WORDSPACE_AT_END_OF_BUFFER
|
|
#define OPTION_WINKEY_STRICT_HOST_OPEN // require an admin host open Winkey command before doing any other commands
|
|
#define OPTION_WINKEY_2_SUPPORT // comment out to revert to Winkey version 1 emulation
|
|
#define OPTION_WINKEY_INTERRUPTS_MEMORY_REPEAT
|
|
//#define OPTION_WINKEY_UCXLOG_9600_BAUD // use this only with UCXLog configured for Winkey 9600 baud mode
|
|
#define OPTION_WINKEY_2_HOST_CLOSE_NO_SERIAL_PORT_RESET // activate this when using Winkey 2 emulation and Win-Test
|
|
#define OPTION_WINKEY_FREQUENT_STATUS_REPORT // activate this to make Winkey emulation play better with RUMlog and RUMped
|
|
#define OPTION_WINKEY_IGNORE_LOWERCASE // Enable for typical K1EL Winkeyer behavior (use for SkookumLogger version 1.10.14 and prior to workaround bug)
|
|
//#define OPTION_REVERSE_BUTTON_ORDER // This is mainly for the DJ0MY NanoKeyer http://nanokeyer.wordpress.com/
|
|
#define OPTION_PROG_MEM_TRIM_TRAILING_SPACES // trim trailing spaces from memory when programming in command mode
|
|
#define OPTION_DIT_PADDLE_NO_SEND_ON_MEM_RPT // this makes dit paddle memory interruption a little smoother
|
|
//#define OPTION_MORE_DISPLAY_MSGS // additional optional display messages - comment out to save memory
|
|
//#define OPTION_WATCHDOG_TIMER // this enables a four second ATmega48/88/168/328 watchdog timer; use for unattended/remote operation only
|
|
//#define OPTION_MOUSE_MOVEMENT_PADDLE // experimental (just fooling around) - mouse movement will act like a paddle
|
|
//#define OPTION_NON_ENGLISH_EXTENSIONS // add support for additional CW characters (i.e. À, Å, Þ, etc.)
|
|
//#define OPTION_KEEP_PTT_KEYED_WHEN_CHARS_BUFFERED // this option keeps PTT high if there are characters buffered from the keyboard, the serial interface, or Winkey
|
|
//#define OPTION_DISPLAY_NON_ENGLISH_EXTENSIONS // LCD display suport for non-English (NO/DK/DE) characters - Courtesy of OZ1JHM
|
|
//#define OPTION_UNKNOWN_CHARACTER_ERROR_TONE
|
|
//#define OPTION_DO_NOT_SAY_HI
|
|
//#define OPTION_PS2_NON_ENGLISH_CHAR_LCD_DISPLAY_SUPPORT // makes some non-English characters from the PS2 keyboard display correctly in the LCD display (donated by Marcin sp5iou)
|
|
//#define OPTION_PS2_KEYBOARD_RESET // reset the PS2 keyboard upon startup with 0xFF (contributed by Bill, W9BEL)
|
|
//#define OPTION_SAVE_MEMORY_NANOKEYER
|
|
//#define OPTION_CW_KEYBOARD_CAPSLOCK_BEEP
|
|
#define OPTION_CW_KEYBOARD_ITALIAN
|
|
//#define OPTION_INVERT_PADDLE_PIN_LOGIC
|
|
#define OPTION_CW_DECODER_GOERTZEL_AUDIO_DETECTOR
|
|
//#define OPTION_ADVANCED_SPEED_DISPLAY //enables "nerd" speed visualization on display: wpm, cpm (char per min), duration of dit and dah in milliseconds and ratio (contributed by Giorgio, IZ2XBZ)
|
|
//#define OPTION_RUSSIAN_LANGUAGE_SEND_CLI // Russian language CLI sending support (contributed by Павел Бирюков, UA1AQC)
|
|
//#define OPTION_DO_NOT_SEND_UNKNOWN_CHAR_QUESTION
|
|
//#define OPTION_CMOS_SUPER_KEYER_IAMBIC_B_TIMING_ON_BY_DEFAULT
|
|
//#define OPTION_SIDETONE_DIGITAL_OUTPUT_NO_SQUARE_WAVE
|
|
|
|
// #define OPTION_WORDSWORTH_CZECH
|
|
// #define OPTION_WORDSWORTH_DEUTSCH
|
|
// #define OPTION_WORDSWORTH_NORSK
|
|
|
|
#define OPTION_EXCLUDE_EXTENDED_CLI_COMMANDS
|
|
|
|
// #define OPTION_DFROBOT_LCD_COMMAND_BUTTONS
|
|
|
|
#define OPTION_EXCLUDE_MILL_MODE
|
|
|