diff --git a/keyer_features_and_options_test.h b/keyer_features_and_options_test.h new file mode 100644 index 0000000..71c0519 --- /dev/null +++ b/keyer_features_and_options_test.h @@ -0,0 +1,103 @@ + +// ######## ######## ###### ######## +// ## ## ## ## ## +// ## ## ## ## +// ## ###### ###### ## +// ## ## ## ## +// ## ## ## ## ## +// ## ######## ###### ## + + +#define FEATURE_COMMAND_BUTTONS +#define FEATURE_COMMAND_LINE_INTERFACE // Command Line Interface functionality +#define FEATURE_MEMORIES // on the Arduino Due, you must have FEATURE_EEPROM_E24C1024 and E24C1024 EEPROM hardware in order to compile this +#define FEATURE_MEMORY_MACROS +// #define FEATURE_WINKEY_EMULATION // disabling Automatic Software Reset is highly recommended (see documentation) (this no longer requires FEATURE_SERIAL) +// #define FEATURE_BEACON +#define FEATURE_CALLSIGN_RECEIVE_PRACTICE +#define FEATURE_POTENTIOMETER // do not enable unless you have a potentiometer connected, otherwise noise will falsely trigger wpm changes +#define FEATURE_SERIAL_HELP +// #define FEATURE_HELL +#define FEATURE_PS2_KEYBOARD // Use a PS2 keyboard to send code - Change keyboard layout (non-US) in K3NG_PS2Keyboard.h. Additional options below. +// #define FEATURE_USB_KEYBOARD // Use a USB keyboard to send code - Uncomment three lines in k3ng_keyer.ino (search for note_usb_uncomment_lines) +// #define FEATURE_CW_COMPUTER_KEYBOARD // Have an Arduino Due or Leonardo act as a USB HID (Human Interface Device) keyboard and use the paddle to "type" characters on the computer +// #define FEATURE_DEAD_OP_WATCHDOG +// #define FEATURE_AUTOSPACE +#define FEATURE_FARNSWORTH +// #define FEATURE_DL2SBA_BANKSWITCH // Switch memory banks feature as described here: http://dl2sba.com/index.php?option=com_content&view=article&id=131:nanokeyer&catid=15:shack&Itemid=27#english +// #define FEATURE_LCD_4BIT // classic LCD disidefplay using 4 I/O lines +// #define FEATURE_LCD_ADAFRUIT_I2C // Adafruit I2C LCD display using MCP23017 at addr 0x20 +// #define FEATURE_LCD_YDv1 // YourDuino I2C LCD display with old LCM 1602 V1 ic +// #define FEATURE_LCD1602_N07DH // http://linksprite.com/wiki/index.php5?title=16_X_2_LCD_Keypad_Shield_for_Arduino +#define FEATURE_CW_DECODER +// #define FEATURE_SLEEP // go to sleep after x minutes to conserve battery power (not compatible with Arduino DUE, may have mixed results with Mega and Mega ADK) +// #define FEATURE_ROTARY_ENCODER // rotary encoder speed control +// #define FEATURE_CMOS_SUPER_KEYER_IAMBIC_B_TIMING +#define FEATURE_DIT_DAH_BUFFER_CONTROL +// #define FEATURE_HI_PRECISION_LOOP_TIMING +// #define FEATURE_USB_MOUSE // Uncomment three lines in k3ng_keyer.ino (search for note_usb_uncomment_lines) +// #define FEATURE_CAPACITIVE_PADDLE_PINS // remove the bypass capacitors on the paddle_left and paddle_right lines when using capactive paddles +// #define FEATURE_LED_RING // Mayhew Labs Led Ring support +// #define FEATURE_ALPHABET_SEND_PRACTICE // enables command mode S command - created by Ryan, KC2ZWM +// #define FEATURE_PTT_INTERLOCK +#define FEATURE_QLF +// #define FEATURE_EEPROM_E24C1024 +#define FEATURE_STRAIGHT_KEY +// #define FEATURE_DYNAMIC_DAH_TO_DIT_RATIO +#define FEATURE_PADDLE_ECHO +#define FEATURE_STRAIGHT_KEY_ECHO + +// #define FEATURE_COMMAND_LINE_INTERFACE_ON_SECONDARY_PORT // Activate the Command Line interface on the secondary serial port +#define OPTION_PRIMARY_SERIAL_PORT_DEFAULT_WINKEY_EMULATION // Use when activating both FEATURE_WINKEY_EMULATION and FEATURE_COMMAND_LINE_INTERFACE + // simultaneously. This will make Winkey emulation be the default at boot up; + // hold command button down at boot up to activate CLI mode + +// #define OPTION_SUPPRESS_SERIAL_BOOT_MSG +#define OPTION_INCLUDE_PTT_TAIL_FOR_MANUAL_SENDING +#define OPTION_EXCLUDE_PTT_HANG_TIME_FOR_MANUAL_SENDING +// #define OPTION_WINKEY_DISCARD_BYTES_AT_STARTUP // if ASR is not disabled, you may need this to discard errant serial port bytes at startup +// #define OPTION_WINKEY_STRICT_EEPROM_WRITES_MAY_WEAR_OUT_EEPROM // with this activated the unit will write non-volatile settings to EEPROM when set by Winkey commands +// #define OPTION_WINKEY_SEND_WORDSPACE_AT_END_OF_BUFFER +#define OPTION_WINKEY_STRICT_HOST_OPEN // require an admin host open Winkey command before doing any other commands +#define OPTION_WINKEY_2_SUPPORT // comment out to revert to Winkey version 1 emulation +// #define OPTION_WINKEY_EXTENDED_COMMANDS // in development +#define OPTION_WINKEY_SEND_BREAKIN_STATUS_BYTE // additional code to check_dit_paddle() and check_dah_paddle() to send 0xC2 status byte when paddles are hit +#define OPTION_WINKEY_INTERRUPTS_MEMORY_REPEAT +// #define OPTION_WINKEY_2_HOST_CLOSE_NO_SERIAL_PORT_RESET // activate this when using Winkey 2 emulation and Win-Test +// #define OPTION_WINKEY_FREQUENT_STATUS_REPORT // activate this to make Winkey emulation play better with RUMlog and RUMped +#define OPTION_WINKEY_IGNORE_LOWERCASE // Enable for typical K1EL Winkeyer behavior (use for SkookumLogger version 1.10.14 and prior to workaround "r" bug) +// #define OPTION_REVERSE_BUTTON_ORDER // This is mainly for the DJ0MY NanoKeyer http://nanokeyer.wordpress.com/ +#define OPTION_PROG_MEM_TRIM_TRAILING_SPACES // trim trailing spaces from memory when programming in command mode +#define OPTION_DIT_PADDLE_NO_SEND_ON_MEM_RPT // this makes dit paddle memory interruption a little smoother +// #define OPTION_MORE_DISPLAY_MSGS // additional optional display messages - comment out to save memory +// #define OPTION_N1MM_WINKEY_TAB_BUG_WORKAROUND // enable this to ignore the TAB key in the Send CW window (this breaks SO2R functionality in N1MM) +// #define OPTION_WATCHDOG_TIMER // this enables a four second ATmega48/88/168/328 watchdog timer; use for unattended/remote operation only +// #define OPTION_MOUSE_MOVEMENT_PADDLE // experimental (just fooling around) - mouse movement will act like a paddle +// #define OPTION_NON_ENGLISH_EXTENSIONS // add support for additional CW characters (i.e. À, Å, Þ, etc.) +// #define OPTION_KEEP_PTT_KEYED_WHEN_CHARS_BUFFERED // this option keeps PTT high if there are characters buffered from the keyboard, the serial interface, or Winkey +// #define OPTION_DISPLAY_NON_ENGLISH_EXTENSIONS // LCD display suport for non-English (NO/DK/DE) characters - Courtesy of OZ1JHM +// #define OPTION_UNKNOWN_CHARACTER_ERROR_TONE +// #define OPTION_DO_NOT_SAY_HI +// #define OPTION_USE_ORIGINAL_VERSION_2_1_PS2KEYBOARD_LIB //use version 2.1 PS2Keyboard.h and PS2Keyboard.cpp for FEATURE_PS2_KEYBOARD +// #define OPTION_PS2_NON_ENGLISH_CHAR_LCD_DISPLAY_SUPPORT // makes some non-English characters from the PS2 keyboard display correctly in the LCD display (donated by Marcin sp5iou) +// #define OPTION_PS2_KEYBOARD_RESET // reset the PS2 keyboard upon startup with 0xFF (contributed by Bill, W9BEL) +// #define OPTION_SAVE_MEMORY_NANOKEYER +#define OPTION_CW_KEYBOARD_CAPSLOCK_BEEP +// #define OPTION_CW_KEYBOARD_ITALIAN +#define OPTION_CW_DECODER_GOERTZEL_AUDIO_DETECTOR +// #define OPTION_INVERT_PADDLE_PIN_LOGIC +// #define OPTION_DIT_DAH_BUFFERS_OFF_BY_DEFAULT_FOR_FEATURE_DIT_DAH_BUFFER_CONTROL +// #define OPTION_ADVANCED_SPEED_DISPLAY //enables "nerd" speed visualization on display: wpm, cpm (char per min), duration of dit and dah in milliseconds and ratio (contributed by Giorgio, IZ2XBZ) +// #define OPTION_PROSIGN_SUPPORT // additional prosign support for paddle and straight key echo on display, CLI, and in memory storage + +// #define FEATURE_COMPETITION_COMPRESSION_DETECTION //(Experimental) + + +// ######## ######## ###### ######## +// ## ## ## ## ## +// ## ## ## ## +// ## ###### ###### ## +// ## ## ## ## +// ## ## ## ## ## +// ## ######## ###### ## + diff --git a/keyer_pin_settings_test.h b/keyer_pin_settings_test.h new file mode 100644 index 0000000..e13f53d --- /dev/null +++ b/keyer_pin_settings_test.h @@ -0,0 +1,118 @@ + +// ######## ######## ###### ######## +// ## ## ## ## ## +// ## ## ## ## +// ## ###### ###### ## +// ## ## ## ## +// ## ## ## ## ## +// ## ######## ###### ## + + +#ifndef keyer_pin_settings_h +#define keyer_pin_settings_h + +#define paddle_left 2 +#define paddle_right 5 +#define tx_key_line_1 11 // (high = key down/tx on) +#define tx_key_line_2 12 +#define tx_key_line_3 0 +#define tx_key_line_4 0 +#define tx_key_line_5 0 +#define tx_key_line_6 0 +#define sidetone_line 4 // connect a speaker for sidetone +#define potentiometer A0 // Speed potentiometer (0 to 5 V) Use pot from 1k to 10k +#define ptt_tx_1 0 // PTT ("push to talk") lines +#define ptt_tx_2 0 // Can be used for keying fox transmitter, T/R switch, or keying slow boatanchors +#define ptt_tx_3 0 // These are optional - set to 0 if unused +#define ptt_tx_4 0 +#define ptt_tx_5 0 +#define ptt_tx_6 0 +#define tx_key_dit 0 // if defined, goes high for dit (any transmitter) +#define tx_key_dah 0 // if defined, goes high for dah (any transmitter) + +#ifdef FEATURE_COMMAND_BUTTONS + #define analog_buttons_pin A1 + #define command_mode_active_led 0 +#endif //FEATURE_COMMAND_BUTTONS + + +//lcd pins +#ifdef FEATURE_LCD_4BIT + #define lcd_rs A2 + #define lcd_enable 10 + #define lcd_d4 6 + #define lcd_d5 7 + #define lcd_d6 8 + #define lcd_d7 9 +#endif //FEATURE_LCD_4BIT + +#ifdef FEATURE_LCD1602_N07DH + #define lcd_rs 8 + #define lcd_enable 9 + #define lcd_d4 4 + #define lcd_d5 5 + #define lcd_d6 6 + #define lcd_d7 7 +#endif //FEATURE_LCD1602_N07DH + +//ps2 keyboard pins +#ifdef FEATURE_PS2_KEYBOARD + #define ps2_keyboard_data A3 + #define ps2_keyboard_clock 3 // this must be on an interrupt capable pin! +#endif //FEATURE_PS2_KEYBOARD + +// rotary encoder pins and options - rotary encoder code from Jim Balls M0CKE +#ifdef FEATURE_ROTARY_ENCODER + #define OPTION_ENCODER_HALF_STEP_MODE // Half-step mode? + #define rotary_pin1 0 // CW Encoder Pin + #define rotary_pin2 0 // CCW Encoder Pin + #define OPTION_ENCODER_ENABLE_PULLUPS // define to enable weak pullups. +#endif //FEATURE_ROTARY_ENCODER + +#ifdef FEATURE_LED_RING + #define led_ring_sdi A10 //2 //Data + #define led_ring_clk A9 //3 //Clock + #define led_ring_le A8 //4 //Latch +#endif //FEATURE_LED_RING + +#ifdef FEATURE_ALPHABET_SEND_PRACTICE + #define correct_answer_led 0 + #define wrong_answer_led 0 +#endif //FEATURE_ALPHABET_SEND_PRACTICE + +#ifdef FEATURE_PTT_INTERLOCK + #define ptt_interlock 0 // this pin disables PTT and TX KEY +#endif //FEATURE_PTT_INTERLOCK + +#ifdef FEATURE_STRAIGHT_KEY + #define pin_straight_key 52 +#endif //FEATURE_STRAIGHT_KEY + +#ifdef FEATURE_CW_DECODER + #define cw_decoder_pin A3//A11 //A5 //A3 + #ifdef OPTION_CW_DECODER_GOERTZEL_AUDIO_DETECTOR + #define cw_decoder_audio_input_pin 0 // this must be an analog pin! + #endif //OPTION_CW_DECODER_GOERTZEL_AUDIO_DETECTOR + #define cw_decoder_indicator 24 +#endif //FEATURE_CW_DECODER + + +#if defined(FEATURE_COMPETITION_COMPRESSION_DETECTION) + #define compression_detection_pin 13 +#endif //FEATURE_COMPETITION_COMPRESSION_DETECTION + +#if defined(FEATURE_SLEEP) + #define keyer_awake 13 // Goes active when keyer is awake, inactive when in sleep mode; change active and inactive states in keyer_settings file +#endif + +#endif //keyer_pin_settings_h + + +// ######## ######## ###### ######## +// ## ## ## ## ## +// ## ## ## ## +// ## ###### ###### ## +// ## ## ## ## +// ## ## ## ## ## +// ## ######## ###### ## + diff --git a/keyer_settings_test.h b/keyer_settings_test.h new file mode 100644 index 0000000..4bc8558 --- /dev/null +++ b/keyer_settings_test.h @@ -0,0 +1,313 @@ + +// ######## ######## ###### ######## +// ## ## ## ## ## +// ## ## ## ## +// ## ###### ###### ## +// ## ## ## ## +// ## ## ## ## ## +// ## ######## ###### ## + + + +#define initial_speed_wpm 26 // "factory default" keyer speed setting +#define initial_sidetone_freq 600 // "factory default" sidetone frequency setting +#define hz_high_beep 1500 // frequency in hertz of high beep +#define hz_low_beep 400 // frequency in hertz of low beep +#define initial_dah_to_dit_ratio 300 // 300 = 3 / normal 3:1 ratio +#define initial_ptt_lead_time_tx1 0 // PTT lead time in mS +#define initial_ptt_tail_time_tx1 10 // PTT tail time in mS +#define initial_ptt_lead_time_tx2 0 // PTT lead time in mS +#define initial_ptt_tail_time_tx2 10 // PTT tail time in mS +#define initial_ptt_lead_time_tx3 0 // PTT lead time in mS +#define initial_ptt_tail_time_tx3 10 // PTT tail time in mS +#define initial_ptt_lead_time_tx4 0 // PTT lead time in mS +#define initial_ptt_tail_time_tx4 10 // PTT tail time in mS +#define initial_ptt_lead_time_tx5 0 // PTT lead time in mS +#define initial_ptt_tail_time_tx5 10 // PTT tail time in mS +#define initial_ptt_lead_time_tx6 0 // PTT lead time in mS +#define initial_ptt_tail_time_tx6 10 // PTT tail time in mS +#define initial_qrss_dit_length 1 // QRSS dit length in seconds +#define initial_pot_wpm_low_value 13 // Potentiometer WPM fully CCW +#define initial_pot_wpm_high_value 35 // Potentiometer WPM fully CW +#define wpm_limit_low 5 +#define wpm_limit_high 60 +#define potentiometer_change_threshold 0.9 // don't change the keyer speed until pot wpm has changed more than this +#define send_buffer_size 150 +#define default_length_letterspace 3 +#define default_length_wordspace 7 +#define default_keying_compensation 0 // number of milliseconds to extend all dits and dahs - for QSK on boatanchors +#define default_first_extension_time 0 // number of milliseconds to extend first sent dit or dah +#define default_pot_full_scale_reading 1023 +#define default_weighting 50 // 50 = weighting factor of 1 (normal) +#define default_ptt_hang_time_wordspace_units 0.0 +#define memory_area_start 30 // the eeprom location where memory space starts +#define memory_area_end 1023 // the eeprom location where memory space ends +#define winkey_c0_wait_time 1 // the number of milliseconds to wait to send 0xc0 byte after send buffer has been sent +#define winkey_command_timeout_ms 5000 +#define winkey_discard_bytes_startup 3 // this is used if OPTION_WINKEY_DISCARD_BYTES_AT_STARTUP is enabled above +#define winkey_xoff_threshold 20 // the number of chars in the buffer when we begin sending XOFFs +#define winkey_xon_threshold 10 // the number of chars in the buffer below which we deactivate XOFF +#define default_memory_repeat_time 3000 // time in milliseconds +#define LCD_COLUMNS 16 +#define LCD_ROWS 2 +#define hell_pixel_microseconds 4025 +#define program_memory_limit_consec_spaces 1 +#define serial_leading_zeros 1 // set to 1 to activate leading zeros in serial numbers (i.e. #1 = 001) +#define serial_cut_numbers 0 // set to 1 to activate cut numbers in serial numbers (i.e. #10 = 1T, #19 = 1N) +#define go_to_sleep_inactivity_time 10 // minutes - FEATURE_SLEEP +#define default_cmos_super_keyer_iambic_b_timing_percent 33 // use with FEATURE_CMOS_SUPER_KEYER_IAMBIC_B_TIMING; should be between 0 to 99 % (0% = true iambic b;100% = iambic a behavior) +#define cw_echo_timing_factor 0.25 +#define potentiometer_always_on 0 +#define ptt_interlock_check_every_ms 100 +#define ptt_interlock_active_state HIGH +#define unknown_cw_character '*' +#define cli_paddle_echo_on_at_boot 1 +#define cli_straight_key_echo_on_at_boot 1 + +#ifdef FEATURE_COMMAND_BUTTONS + #define analog_buttons_number_of_buttons 4 + #define analog_buttons_r1 10 + #define analog_buttons_r2 1 +#endif + + +#if defined(FEATURE_COMMAND_BUTTONS) && !defined(FEATURE_PS2_KEYBOARD) && !defined(FEATURE_USB_KEYBOARD) && !defined(FEATURE_COMMAND_LINE_INTERFACE) && !defined(FEATURE_WINKEY_EMULATION) + #define number_of_memories byte(analog_buttons_number_of_buttons-1) +#else + #define number_of_memories byte(12) +#endif + +#ifdef FEATURE_CAPACITIVE_PADDLE_PINS + #define capacitance_threshold 2 +#endif //FEATURE_CAPACITIVE_PADDLE_PINS + +#ifdef FEATURE_LED_RING + #define led_ring_low_limit 10 + #define led_ring_high_limit 50 +#endif //FEATURE_LED_RING + +#ifdef FEATURE_QLF + #define qlf_dit_max 125 + #define qlf_dit_min 75 + #define qlf_dah_max 200 + #define qlf_dah_min 100 + #define qlf_on_by_default 0 +#endif //FEATURE_QLF + +// Variable macros +#define STRAIGHT 1 +#define IAMBIC_B 2 +#define IAMBIC_A 3 +#define BUG 4 +#define ULTIMATIC 5 + +#define PADDLE_NORMAL 0 +#define PADDLE_REVERSE 1 + +#define KEYER_NORMAL 0 +#define BEACON 1 +#define KEYER_COMMAND_MODE 2 + +#define OMIT_LETTERSPACE 1 + +#define SIDETONE_OFF 0 +#define SIDETONE_ON 1 +#define SIDETONE_PADDLE_ONLY 2 + +#define SENDING_NOTHING 0 +#define SENDING_DIT 1 +#define SENDING_DAH 2 + +#define SPEED_NORMAL 0 +#define SPEED_QRSS 1 + +#define CW 0 +#define HELL 1 + +#ifdef FEATURE_PS2_KEYBOARD + #define PS2_KEYBOARD_NORMAL 0 +#endif //FEATURE_PS2_KEYBOARD + +#define SERIAL_CLI 0 +#define SERIAL_WINKEY_EMULATION 1 + +#define SERIAL_SEND_BUFFER_SPECIAL_START 13 +#define SERIAL_SEND_BUFFER_WPM_CHANGE 14 +#define SERIAL_SEND_BUFFER_PTT_ON 15 +#define SERIAL_SEND_BUFFER_PTT_OFF 16 +#define SERIAL_SEND_BUFFER_TIMED_KEY_DOWN 17 +#define SERIAL_SEND_BUFFER_TIMED_WAIT 18 +#define SERIAL_SEND_BUFFER_NULL 19 +#define SERIAL_SEND_BUFFER_PROSIGN 20 +#define SERIAL_SEND_BUFFER_HOLD_SEND 21 +#define SERIAL_SEND_BUFFER_HOLD_SEND_RELEASE 22 +#define SERIAL_SEND_BUFFER_MEMORY_NUMBER 23 +#define SERIAL_SEND_BUFFER_SPECIAL_END 24 + +#if defined(OPTION_PROSIGN_SUPPORT) + #define PROSIGN_START 127 + #define PROSIGN_AA 128 + #define PROSIGN_AS 129 + #define PROSIGN_BK 130 + #define PROSIGN_CL 131 + #define PROSIGN_CT 132 + #define PROSIGN_KN 133 + #define PROSIGN_NJ 134 + #define PROSIGN_SK 135 + #define PROSIGN_SN 136 + #define PROSIGN_END 137 +#endif + +#define SERIAL_SEND_BUFFER_NORMAL 0 +#define SERIAL_SEND_BUFFER_TIMED_COMMAND 1 +#define SERIAL_SEND_BUFFER_HOLD 2 + +#ifdef FEATURE_WINKEY_EMULATION +#define WINKEY_NO_COMMAND_IN_PROGRESS 0 +#define WINKEY_UNBUFFERED_SPEED_COMMAND 1 +#define WINKEY_UNSUPPORTED_COMMAND 2 +#define WINKEY_POINTER_COMMAND 3 +#define WINKEY_ADMIN_COMMAND 4 +#define WINKEY_PAUSE_COMMAND 5 +#define WINKEY_KEY_COMMAND 6 +#define WINKEY_SETMODE_COMMAND 7 +#define WINKEY_SIDETONE_FREQ_COMMAND 8 +#define WINKEY_ADMIN_COMMAND_ECHO 9 +#define WINKEY_BUFFERED_SPEED_COMMAND 10 +#define WINKEY_DAH_TO_DIT_RATIO_COMMAND 11 +#define WINKEY_KEYING_COMPENSATION_COMMAND 12 +#define WINKEY_FIRST_EXTENSION_COMMAND 13 +#define WINKEY_PTT_TIMES_PARM1_COMMAND 14 +#define WINKEY_PTT_TIMES_PARM2_COMMAND 15 +#define WINKEY_SET_POT_PARM1_COMMAND 16 +#define WINKEY_SET_POT_PARM2_COMMAND 17 +#define WINKEY_SET_POT_PARM3_COMMAND 18 +#define WINKEY_SOFTWARE_PADDLE_COMMAND 19 +#define WINKEY_CANCEL_BUFFERED_SPEED_COMMAND 20 +#define WINKEY_BUFFFERED_PTT_COMMMAND 21 +#define WINKEY_HSCW_COMMAND 22 +#define WINKEY_BUFFERED_HSCW_COMMAND 23 +#define WINKEY_WEIGHTING_COMMAND 24 +#define WINKEY_KEY_BUFFERED_COMMAND 25 +#define WINKEY_WAIT_BUFFERED_COMMAND 26 +#define WINKEY_POINTER_01_COMMAND 27 +#define WINKEY_POINTER_02_COMMAND 28 +#define WINKEY_POINTER_03_COMMAND 29 +#define WINKEY_FARNSWORTH_COMMAND 30 +#define WINKEY_MERGE_COMMAND 31 +#define WINKEY_MERGE_PARM_2_COMMAND 32 +#define WINKEY_SET_PINCONFIG_COMMAND 33 +#define WINKEY_EXTENDED_COMMAND 34 +#ifdef OPTION_WINKEY_2_SUPPORT +#define WINKEY_SEND_MSG 35 +#endif //OPTION_WINKEY_2_SUPPORT +#define WINKEY_LOAD_SETTINGS_PARM_1_COMMAND 101 +#define WINKEY_LOAD_SETTINGS_PARM_2_COMMAND 102 +#define WINKEY_LOAD_SETTINGS_PARM_3_COMMAND 103 +#define WINKEY_LOAD_SETTINGS_PARM_4_COMMAND 104 +#define WINKEY_LOAD_SETTINGS_PARM_5_COMMAND 105 +#define WINKEY_LOAD_SETTINGS_PARM_6_COMMAND 106 +#define WINKEY_LOAD_SETTINGS_PARM_7_COMMAND 107 +#define WINKEY_LOAD_SETTINGS_PARM_8_COMMAND 108 +#define WINKEY_LOAD_SETTINGS_PARM_9_COMMAND 109 +#define WINKEY_LOAD_SETTINGS_PARM_10_COMMAND 110 +#define WINKEY_LOAD_SETTINGS_PARM_11_COMMAND 111 +#define WINKEY_LOAD_SETTINGS_PARM_12_COMMAND 112 +#define WINKEY_LOAD_SETTINGS_PARM_13_COMMAND 113 +#define WINKEY_LOAD_SETTINGS_PARM_14_COMMAND 114 +#define WINKEY_LOAD_SETTINGS_PARM_15_COMMAND 115 + +#define WINKEY_HOUSEKEEPING 0 +#define SERVICE_SERIAL_BYTE 1 +#endif //FEATURE_WINKEY_EMULATION + +#define AUTOMATIC_SENDING 0 +#define MANUAL_SENDING 1 + +#define ULTIMATIC_NORMAL 0 +#define ULTIMATIC_DIT_PRIORITY 1 +#define ULTIMATIC_DAH_PRIORITY 2 + +#ifdef FEATURE_WINKEY_EMULATION +// alter these below to map alternate sidetones for Winkey interface protocol emulation +#ifdef OPTION_WINKEY_2_SUPPORT + #define WINKEY_SIDETONE_1 3759 + #define WINKEY_SIDETONE_2 1879 + #define WINKEY_SIDETONE_3 1252 + #define WINKEY_SIDETONE_4 940 + #define WINKEY_SIDETONE_5 752 + #define WINKEY_SIDETONE_6 625 + #define WINKEY_SIDETONE_7 535 + #define WINKEY_SIDETONE_8 469 + #define WINKEY_SIDETONE_9 417 + #define WINKEY_SIDETONE_10 375 +#else //OPTION_WINKEY_2_SUPPORT + #define WINKEY_SIDETONE_1 4000 + #define WINKEY_SIDETONE_2 2000 + #define WINKEY_SIDETONE_3 1333 + #define WINKEY_SIDETONE_4 1000 + #define WINKEY_SIDETONE_5 800 + #define WINKEY_SIDETONE_6 666 + #define WINKEY_SIDETONE_7 571 + #define WINKEY_SIDETONE_8 500 + #define WINKEY_SIDETONE_9 444 + #define WINKEY_SIDETONE_10 400 +#endif //OPTION_WINKEY_2_SUPPORT + +#define WINKEY_1_REPORT_VERSION_NUMBER 10 +#define WINKEY_2_REPORT_VERSION_NUMBER 23 + +// alter these to map to alternate hang time wordspace units +#define WINKEY_HANG_TIME_1_0 1.0 +#define WINKEY_HANG_TIME_1_33 1.33 +#define WINKEY_HANG_TIME_1_66 1.66 +#define WINKEY_HANG_TIME_2_0 2.0 + +#endif //FEATURE_WINKEY_EMULATION + +#define PRINTCHAR 0 +#define NOPRINT 1 + +#define PRIMARY_SERIAL_PORT &Serial +#define PRIMARY_SERIAL_PORT_BAUD 115200 // This applies only when the port is in Command Line Interface mode. In Winkey mode it will default to 1200. + +#ifdef FEATURE_COMMAND_LINE_INTERFACE_ON_SECONDARY_PORT + #define SECONDARY_SERIAL_PORT &Serial1 + #define SECONDARY_SERIAL_PORT_BAUD 115200 +#endif + + +#define CW_DECODER_SCREEN_COLUMNS 120 // word wrap at this many columns +#define CW_DECODER_SPACE_PRINT_THRESH 4.5 // print space if no tone for this many element lengths +#define CW_DECODER_SPACE_DECODE_THRESH 2.0 // invoke character decode if no tone for this many element lengths +#define CW_DECODER_NOISE_FILTER 20 // ignore elements shorter than this (mS) + +#define STRAIGHT_KEY_ACTIVE_STATE LOW + +#ifdef FEATURE_DYNAMIC_DAH_TO_DIT_RATIO + #define DYNAMIC_DAH_TO_DIT_RATIO_LOWER_LIMIT_WPM 30 + #define DYNAMIC_DAH_TO_DIT_RATIO_LOWER_LIMIT_RATIO 300 // 300 = 3:1 ratio + #define DYNAMIC_DAH_TO_DIT_RATIO_UPPER_LIMIT_WPM 70 + #define DYNAMIC_DAH_TO_DIT_RATIO_UPPER_LIMIT_RATIO 240 // 240 = 2.4:1 ratio +#endif //FEATURE_DYNAMIC_DAH_TO_DIT_RATIO + +#if defined(FEATURE_COMPETITION_COMPRESSION_DETECTION) + #define COMPETITION_COMPRESSION_DETECTION_ARRAY_SIZE 16 + #define COMPETITION_COMPRESSION_DETECTION_TIME_INTERCHAR_LOWER_LIMIT 1 + #define COMPETITION_COMPRESSION_DETECTION_TIME_INTERCHAR_UPPER_LIMIT 6.0 + #define COMPETITION_COMPRESSION_DETECTION_AVERAGE_ALARM_THRESHOLD 3.0 +#endif //FEATURE_COMPETITION_COMPRESSION_DETECTION + +#if defined(FEATURE_SLEEP) + #define KEYER_AWAKE_PIN_AWAKE_STATE HIGH + #define KEYER_AWAKE_PIN_ASLEEP_STATE LOW +#endif + + +// ######## ######## ###### ######## +// ## ## ## ## ## +// ## ## ## ## +// ## ###### ###### ## +// ## ## ## ## +// ## ## ## ## ## +// ## ######## ###### ## diff --git a/libraries/README.md b/libraries/README.md new file mode 100644 index 0000000..31ee67c --- /dev/null +++ b/libraries/README.md @@ -0,0 +1 @@ +AS OF VERSION 2.2.2016012004 LIBRARY FILES MUST BE PUT IN LIBRARIES DIRECTORY AND NOT THE INO SKETCH DIRECTORY !!!!