2024.03.15.1354

FEATURE_WINKEY_EMULATION: Changed potentiometer behavior to work correctly with N1MM+ pot settings

k3ng_keyer/k3ng_keyer.ino

@@ -1411,6 +1411,9 @@ Recent Update History
     2024.02.28.0239
       FEATURE_MORTTY_SPEEDPOT_BOOT_FUNCTION
 
+    2024.03.15.1354
+      FEATURE_WINKEY_EMULATION: Changed potentiometer behavior to work correctly with N1MM+ pot settings
+
   qwerty
 
   Documentation: https://github.com/k3ng/k3ng_cw_keyer/wiki
@@ -5660,15 +5663,26 @@ void check_potentiometer()
         debug_serial_port->print(F(" analog read: "));
         debug_serial_port->println(analogRead(potentiometer));
       #endif
-      if (keyer_machine_mode == KEYER_COMMAND_MODE) command_speed_set(pot_value_wpm_read);
-      else speed_set(pot_value_wpm_read);
-      last_pot_wpm_read = pot_value_wpm_read;
       #ifdef FEATURE_WINKEY_EMULATION
+        if (keyer_machine_mode == KEYER_COMMAND_MODE) {
+          command_speed_set(pot_value_wpm_read);
+        } else {
+          if (!winkey_host_open){
+            speed_set(pot_value_wpm_read);
+          }
+        }
         if ((primary_serial_port_mode == SERIAL_WINKEY_EMULATION) && (winkey_host_open)) {
           winkey_port_write(((pot_value_wpm_read-pot_wpm_low_value)|128),0);
           winkey_last_unbuffered_speed_wpm = configuration.wpm;
+        }        
+      #else
+        if (keyer_machine_mode == KEYER_COMMAND_MODE) {
+          command_speed_set(pot_value_wpm_read);
+        } else {
+          speed_set(pot_value_wpm_read);
         }
       #endif
+      last_pot_wpm_read = pot_value_wpm_read;
       #ifdef FEATURE_SLEEP
         last_activity_time = millis();
       #endif //FEATURE_SLEEP
@@ -10744,6 +10758,7 @@ void winkey_ptt_times_parm2_command(byte incoming_serial_byte) {
 #ifdef FEATURE_WINKEY_EMULATION
 void winkey_set_pot_parm1_command(byte incoming_serial_byte) {
 
+  
   pot_wpm_low_value = incoming_serial_byte;
 
 }

k3ng_keyer/keyer_features_and_options_test.h

@@ -13,16 +13,16 @@
 #if defined(TEST_CONFIG_1)
 
 
-#define FEATURE_BUTTONS
-#define FEATURE_COMMAND_MODE
-// #define FEATURE_COMMAND_LINE_INTERFACE  // Command Line Interface functionality
+// #define FEATURE_BUTTONS
+// #define FEATURE_COMMAND_MODE
+#define FEATURE_COMMAND_LINE_INTERFACE  // Command Line Interface functionality
 // #define FEATURE_MEMORIES             // on the Arduino Due, you must have FEATURE_EEPROM_E24C1024 and E24C1024 EEPROM hardware in order to compile this
 // #define FEATURE_MEMORY_MACROS
 #define FEATURE_WINKEY_EMULATION    // disabling Automatic Software Reset is highly recommended (see documentation)
 // #define FEATURE_BEACON                // Go into beacon mode if paddle_left pin is LOW at boot up
 // #define FEATURE_BEACON_SETTING        // Go into beacon mode at boot up if EEPROM setting is enabled (\_ CLI Command)
 // #define FEATURE_TRAINING_COMMAND_LINE_INTERFACE
-// #define FEATURE_POTENTIOMETER         // do not enable unless you have a potentiometer connected, otherwise noise will falsely trigger wpm changes
+#define FEATURE_POTENTIOMETER         // do not enable unless you have a potentiometer connected, otherwise noise will falsely trigger wpm changes
 // #define FEATURE_SIDETONE_SWITCH   // adds switch control for the sidetone output. requires an external toggle switch (assigned to an arduino pin - see keyer_pin_settings.h). 
 // #define FEATURE_SIDETONE_NEWTONE      // Use the NewTone library, ~1k smaller code size than the standard tone library. Uses timer1 (pins 9 or 10)  https://bitbucket.org/teckel12/arduino-new-tone/wiki/Home
 // #define FEATURE_SERIAL_HELP

k3ng_keyer/keyer_pin_settings_test.h

@@ -17,7 +17,7 @@
 #define paddle_left 2
 #define paddle_right 5
 #define sidetone_line 4
-#define potentiometer A0 
+#define potentiometer 28 //A0 // Pico test jig: 28 (GP28)
 #define ptt_tx_1 13              // PTT ("push to talk") lines
 
 //Raspberry Pi Pico Test Jig