2015-04-30 01:19:51 +00:00
// Initial and hardcoded settings
# define initial_speed_wpm 26 // "factory default" keyer speed setting
# define initial_sidetone_freq 600 // "factory default" sidetone frequency setting
# define hz_high_beep 1500 // frequency in hertz of high beep
# define hz_low_beep 400 // frequency in hertz of low beep
# define initial_dah_to_dit_ratio 300 // 300 = 3 / normal 3:1 ratio
# define initial_ptt_lead_time_tx1 0 // PTT lead time in mS
# define initial_ptt_tail_time_tx1 10 // PTT tail time in mS
# define initial_ptt_lead_time_tx2 0 // PTT lead time in mS
# define initial_ptt_tail_time_tx2 10 // PTT tail time in mS
# define initial_ptt_lead_time_tx3 0 // PTT lead time in mS
# define initial_ptt_tail_time_tx3 10 // PTT tail time in mS
# define initial_ptt_lead_time_tx4 0 // PTT lead time in mS
# define initial_ptt_tail_time_tx4 10 // PTT tail time in mS
# define initial_ptt_lead_time_tx5 0 // PTT lead time in mS
# define initial_ptt_tail_time_tx5 10 // PTT tail time in mS
# define initial_ptt_lead_time_tx6 0 // PTT lead time in mS
# define initial_ptt_tail_time_tx6 10 // PTT tail time in mS
# define initial_qrss_dit_length 1 // QRSS dit length in seconds
# define initial_pot_wpm_low_value 13 // Potentiometer WPM fully CCW
# define initial_pot_wpm_high_value 35 // Potentiometer WPM fully CW
# define wpm_limit_low 5
# define wpm_limit_high 60
# define potentiometer_change_threshold 1 // don't change the keyer speed until pot wpm has changed more than this
# define send_buffer_size 150
# define default_length_letterspace 3
# define default_length_wordspace 7
# define default_keying_compensation 0 // number of milliseconds to extend all dits and dahs - for QSK on boatanchors
# define default_first_extension_time 0 // number of milliseconds to extend first sent dit or dah
# define default_pot_full_scale_reading 1023
# define default_weighting 50 // 50 = weighting factor of 1 (normal)
# define default_ptt_hang_time_wordspace_units 0.0
# define memory_area_start 30 // the eeprom location where memory space starts
# define memory_area_end 1023 // the eeprom location where memory space ends
# define winkey_c0_wait_time 1 // the number of milliseconds to wait to send 0xc0 byte after send buffer has been sent
# define winkey_command_timeout_ms 5000
# define winkey_discard_bytes_startup 3 // this is used if OPTION_WINKEY_DISCARD_BYTES_AT_STARTUP is enabled above
# define winkey_xoff_threshold 20 // the number of chars in the buffer when we begin sending XOFFs
# define winkey_xon_threshold 10 // the number of chars in the buffer below which we deactivate XOFF
# define default_memory_repeat_time 3000 // time in milliseconds
2015-06-11 23:37:34 +00:00
# define LCD_COLUMNS 16
# define LCD_ROWS 2
2015-04-30 01:19:51 +00:00
# define hell_pixel_microseconds 4025
# define program_memory_limit_consec_spaces 1
# define serial_leading_zeros 1 // set to 1 to activate leading zeros in serial numbers (i.e. #1 = 001)
# define serial_cut_numbers 0 // set to 1 to activate cut numbers in serial numbers (i.e. #10 = 1T, #19 = 1N)
# define go_to_sleep_inactivity_time 10 // minutes - FEATURE_SLEEP
# define default_cmos_super_keyer_iambic_b_timing_percent 33 // use with FEATURE_CMOS_SUPER_KEYER_IAMBIC_B_TIMING; should be between 0 to 99 % (0% = true iambic b;100% = iambic a behavior)
# define cw_echo_timing_factor 0.25
# define potentiometer_always_on 0
# define ptt_interlock_check_every_ms 100
# define ptt_interlock_active_state HIGH
# define unknown_cw_character '*'
# ifdef FEATURE_COMMAND_BUTTONS
# define analog_buttons_number_of_buttons 4
# define analog_buttons_r1 10
# define analog_buttons_r2 1
# endif
# if defined(FEATURE_COMMAND_BUTTONS) && !defined(FEATURE_PS2_KEYBOARD) && !defined(FEATURE_USB_KEYBOARD) && !defined(FEATURE_COMMAND_LINE_INTERFACE) && !defined(FEATURE_WINKEY_EMULATION)
# define number_of_memories byte(analog_buttons_number_of_buttons-1)
# else
# define number_of_memories byte(12)
# endif
# ifdef FEATURE_CAPACITIVE_PADDLE_PINS
# define capacitance_threshold 2
# endif //FEATURE_CAPACITIVE_PADDLE_PINS
# ifdef FEATURE_LED_RING
# define led_ring_low_limit 10
# define led_ring_high_limit 50
# endif //FEATURE_LED_RING
# ifdef FEATURE_QLF
# define qlf_dit_max 125
# define qlf_dit_min 75
# define qlf_dah_max 200
# define qlf_dah_min 100
# define qlf_on_by_default 0
# endif //FEATURE_QLF
// Variable macros
# define STRAIGHT 1
# define IAMBIC_B 2
# define IAMBIC_A 3
# define BUG 4
# define ULTIMATIC 5
# define PADDLE_NORMAL 0
# define PADDLE_REVERSE 1
# define KEYER_NORMAL 0
# define BEACON 1
# define KEYER_COMMAND_MODE 2
# define OMIT_LETTERSPACE 1
# define SIDETONE_OFF 0
# define SIDETONE_ON 1
# define SIDETONE_PADDLE_ONLY 2
# define SENDING_NOTHING 0
# define SENDING_DIT 1
# define SENDING_DAH 2
# define SPEED_NORMAL 0
# define SPEED_QRSS 1
# define CW 0
# define HELL 1
# ifdef FEATURE_PS2_KEYBOARD
# define PS2_KEYBOARD_NORMAL 0
# endif //FEATURE_PS2_KEYBOARD
# define SERIAL_CLI 0
# define SERIAL_WINKEY_EMULATION 1
# define SERIAL_SEND_BUFFER_SPECIAL_START 13
# define SERIAL_SEND_BUFFER_WPM_CHANGE 14
# define SERIAL_SEND_BUFFER_PTT_ON 15
# define SERIAL_SEND_BUFFER_PTT_OFF 16
# define SERIAL_SEND_BUFFER_TIMED_KEY_DOWN 17
# define SERIAL_SEND_BUFFER_TIMED_WAIT 18
# define SERIAL_SEND_BUFFER_NULL 19
# define SERIAL_SEND_BUFFER_PROSIGN 20
# define SERIAL_SEND_BUFFER_HOLD_SEND 21
# define SERIAL_SEND_BUFFER_HOLD_SEND_RELEASE 22
# define SERIAL_SEND_BUFFER_MEMORY_NUMBER 23
# define SERIAL_SEND_BUFFER_SPECIAL_END 24
# define SERIAL_SEND_BUFFER_NORMAL 0
# define SERIAL_SEND_BUFFER_TIMED_COMMAND 1
# define SERIAL_SEND_BUFFER_HOLD 2
# ifdef FEATURE_WINKEY_EMULATION
# define WINKEY_NO_COMMAND_IN_PROGRESS 0
# define WINKEY_UNBUFFERED_SPEED_COMMAND 1
# define WINKEY_UNSUPPORTED_COMMAND 2
# define WINKEY_POINTER_COMMAND 3
# define WINKEY_ADMIN_COMMAND 4
# define WINKEY_PAUSE_COMMAND 5
# define WINKEY_KEY_COMMAND 6
# define WINKEY_SETMODE_COMMAND 7
# define WINKEY_SIDETONE_FREQ_COMMAND 8
# define WINKEY_ADMIN_COMMAND_ECHO 9
# define WINKEY_BUFFERED_SPEED_COMMAND 10
# define WINKEY_DAH_TO_DIT_RATIO_COMMAND 11
# define WINKEY_KEYING_COMPENSATION_COMMAND 12
# define WINKEY_FIRST_EXTENSION_COMMAND 13
# define WINKEY_PTT_TIMES_PARM1_COMMAND 14
# define WINKEY_PTT_TIMES_PARM2_COMMAND 15
# define WINKEY_SET_POT_PARM1_COMMAND 16
# define WINKEY_SET_POT_PARM2_COMMAND 17
# define WINKEY_SET_POT_PARM3_COMMAND 18
# define WINKEY_SOFTWARE_PADDLE_COMMAND 19
# define WINKEY_CANCEL_BUFFERED_SPEED_COMMAND 20
# define WINKEY_BUFFFERED_PTT_COMMMAND 21
# define WINKEY_HSCW_COMMAND 22
# define WINKEY_BUFFERED_HSCW_COMMAND 23
# define WINKEY_WEIGHTING_COMMAND 24
# define WINKEY_KEY_BUFFERED_COMMAND 25
# define WINKEY_WAIT_BUFFERED_COMMAND 26
# define WINKEY_POINTER_01_COMMAND 27
# define WINKEY_POINTER_02_COMMAND 28
# define WINKEY_POINTER_03_COMMAND 29
# define WINKEY_FARNSWORTH_COMMAND 30
# define WINKEY_MERGE_COMMAND 31
# define WINKEY_MERGE_PARM_2_COMMAND 32
# define WINKEY_SET_PINCONFIG_COMMAND 33
# define WINKEY_EXTENDED_COMMAND 34
# ifdef OPTION_WINKEY_2_SUPPORT
# define WINKEY_SEND_MSG 35
# endif //OPTION_WINKEY_2_SUPPORT
# define WINKEY_LOAD_SETTINGS_PARM_1_COMMAND 101
# define WINKEY_LOAD_SETTINGS_PARM_2_COMMAND 102
# define WINKEY_LOAD_SETTINGS_PARM_3_COMMAND 103
# define WINKEY_LOAD_SETTINGS_PARM_4_COMMAND 104
# define WINKEY_LOAD_SETTINGS_PARM_5_COMMAND 105
# define WINKEY_LOAD_SETTINGS_PARM_6_COMMAND 106
# define WINKEY_LOAD_SETTINGS_PARM_7_COMMAND 107
# define WINKEY_LOAD_SETTINGS_PARM_8_COMMAND 108
# define WINKEY_LOAD_SETTINGS_PARM_9_COMMAND 109
# define WINKEY_LOAD_SETTINGS_PARM_10_COMMAND 110
# define WINKEY_LOAD_SETTINGS_PARM_11_COMMAND 111
# define WINKEY_LOAD_SETTINGS_PARM_12_COMMAND 112
# define WINKEY_LOAD_SETTINGS_PARM_13_COMMAND 113
# define WINKEY_LOAD_SETTINGS_PARM_14_COMMAND 114
# define WINKEY_LOAD_SETTINGS_PARM_15_COMMAND 115
# define WINKEY_HOUSEKEEPING 0
# define SERVICE_SERIAL_BYTE 1
# endif //FEATURE_WINKEY_EMULATION
# define AUTOMATIC_SENDING 0
# define MANUAL_SENDING 1
# define ULTIMATIC_NORMAL 0
# define ULTIMATIC_DIT_PRIORITY 1
# define ULTIMATIC_DAH_PRIORITY 2
# ifdef FEATURE_WINKEY_EMULATION
// alter these below to map alternate sidetones for Winkey interface protocol emulation
# ifdef OPTION_WINKEY_2_SUPPORT
# define WINKEY_SIDETONE_1 3759
# define WINKEY_SIDETONE_2 1879
# define WINKEY_SIDETONE_3 1252
# define WINKEY_SIDETONE_4 940
# define WINKEY_SIDETONE_5 752
# define WINKEY_SIDETONE_6 625
# define WINKEY_SIDETONE_7 535
# define WINKEY_SIDETONE_8 469
# define WINKEY_SIDETONE_9 417
# define WINKEY_SIDETONE_10 375
# else //OPTION_WINKEY_2_SUPPORT
# define WINKEY_SIDETONE_1 4000
# define WINKEY_SIDETONE_2 2000
# define WINKEY_SIDETONE_3 1333
# define WINKEY_SIDETONE_4 1000
# define WINKEY_SIDETONE_5 800
# define WINKEY_SIDETONE_6 666
# define WINKEY_SIDETONE_7 571
# define WINKEY_SIDETONE_8 500
# define WINKEY_SIDETONE_9 444
# define WINKEY_SIDETONE_10 400
# endif //OPTION_WINKEY_2_SUPPORT
# define WINKEY_1_REPORT_VERSION_NUMBER 10
# define WINKEY_2_REPORT_VERSION_NUMBER 23
// alter these to map to alternate hang time wordspace units
# define WINKEY_HANG_TIME_1_0 1.0
# define WINKEY_HANG_TIME_1_33 1.33
# define WINKEY_HANG_TIME_1_66 1.66
# define WINKEY_HANG_TIME_2_0 2.0
# endif //FEATURE_WINKEY_EMULATION
# define PRINTCHAR 0
# define NOPRINT 1
# define PRIMARY_SERIAL_PORT &Serial
# define PRIMARY_SERIAL_PORT_BAUD 115200 // This applies only when the port is in Command Line Interface mode. In Winkey mode it will default to 1200.
# ifdef FEATURE_COMMAND_LINE_INTERFACE_ON_SECONDARY_PORT
# define SECONDARY_SERIAL_PORT &Serial1
# define SECONDARY_SERIAL_PORT_BAUD 115200
# endif
# define CW_DECODER_SCREEN_COLUMNS 40 // word wrap at this many columns
# define CW_DECODER_SPACE_PRINT_THRESH 4.5 // print space if no tone for this many element lengths
# define CW_DECODER_SPACE_DECODE_THRESH 2.0 // invoke character decode if no tone for this many element lengths
# define CW_DECODER_NOISE_FILTER 20 // ignore elements shorter than this (mS)
