2013-08-29 01:35:16 +00:00
// compile time features and options - comment or uncomment to add or delete features
// FEATURES add more bytes to the compiled binary, OPTIONS change code behavior
2013-12-26 15:23:45 +00:00
2013-08-29 01:35:16 +00:00
# define FEATURE_SERIAL
2014-07-11 02:17:13 +00:00
# define FEATURE_COMMAND_LINE_INTERFACE // this requires FEATURE_SERIAL
//define FEATURE_COMMAND_BUTTONS // do not enable unless you have the corresponding resistors connected to the analog_buttons_pin
2014-02-21 01:10:09 +00:00
# define FEATURE_SAY_HI
2014-07-11 02:17:13 +00:00
//#define FEATURE_MEMORIES
2013-08-29 01:35:16 +00:00
//#define FEATURE_MEMORY_MACROS
2014-07-11 02:17:13 +00:00
//#define FEATURE_WINKEY_EMULATION // this requires FEATURE_SERIAL - disabling Automatic Software Reset is highly recommended (see documentation)
//#define OPTION_WINKEY_2_SUPPORT // requires FEATURE_WINKEY_EMULATION
2013-08-29 01:35:16 +00:00
//#define FEATURE_BEACON
2013-11-27 18:52:23 +00:00
//#define FEATURE_CALLSIGN_RECEIVE_PRACTICE
2013-08-29 01:35:16 +00:00
//#define FEATURE_POTENTIOMETER // do not enable unless you have a potentiometer connected, otherwise noise will falsely trigger wpm changes
//#define FEATURE_SERIAL_HELP
//#define FEATURE_HELL
//#define FEATURE_PS2_KEYBOARD // also uncomment PS2Keyboard line below and PS2Keyboard.h include at the top (requires FEATURE_SERIAL)
//#define FEATURE_USB_KEYBOARD // also uncomment FEATURE_USB_KEYBOARD section below
//#define FEATURE_DEAD_OP_WATCHDOG
//#define FEATURE_AUTOSPACE
//#define FEATURE_FARNSWORTH
//#define FEATURE_DL2SBA_BANKSWITCH // Switch memory banks feature as described here: http://dl2sba.com/index.php?option=com_content&view=article&id=131:nanokeyer&catid=15:shack&Itemid=27#english
2014-03-11 01:01:56 +00:00
//#define FEATURE_DISPLAY // LCD display support (include one of the hardware options below)
//#define FEATURE_LCD_4BIT // classic LCD disidefplay using 4 I/O lines
2013-12-26 13:41:57 +00:00
//#define FEATURE_LCD_ADAFRUIT_I2C // Adafruit I2C LCD display using MCP23017 at addr 0x20
//#define FEATURE_LCD_YDv1 // YourDuino I2C LCD display with old LCM 1602 V1 ic
2014-01-09 23:53:59 +00:00
//#define FEATURE_CW_DECODER
//#define FEATURE_SLEEP // go to sleep after x minutes to conserve battery power
//#define FEATURE_ROTARY_ENCODER // rotary encoder speed control
//#define FEATURE_CMOS_SUPER_KEYER_IAMBIC_B_TIMING
//#define FEATURE_DIT_DAH_BUFFER_CONTROL
2013-08-29 01:35:16 +00:00
//#define FEATURE_HI_PRECISION_LOOP_TIMING
//#define FEATURE_USB_MOUSE
2014-02-16 13:02:10 +00:00
//#define FEATURE_CAPACITIVE_PADDLE_PINS // remove the bypass capacitors on the paddle_left and paddle_right lines when using capactive paddles
2013-08-29 01:35:16 +00:00
//#define FEATURE_LED_RING // Mayhew Labs Led Ring support
2014-07-03 23:48:40 +00:00
//#define FEATURE_ALPHABET_SEND_PRACTICE // enables command mode S command - created by Ryan, KC2ZWM
2013-08-29 01:35:16 +00:00
//#define OPTION_SUPPRESS_SERIAL_BOOT_MSG
# define OPTION_INCLUDE_PTT_TAIL_FOR_MANUAL_SENDING
2014-03-05 00:58:02 +00:00
# define OPTION_EXCLUDE_PTT_HANG_TIME_FOR_MANUAL_SENDING
2013-08-29 01:35:16 +00:00
# define OPTION_SERIAL_PORT_DEFAULT_WINKEY_EMULATION // this will make Winkey emulation be the default at boot up; hold command button down at boot up to activate CLI mode
//#define OPTION_WINKEY_DISCARD_BYTES_AT_STARTUP // if ASR is not disabled, you may need this to discard errant serial port bytes at startup
//#define OPTION_WINKEY_STRICT_EEPROM_WRITES_MAY_WEAR_OUT_EEPROM // with this activated the unit will write non-volatile settings to EEPROM when set by Winkey commands
//#define OPTION_WINKEY_SEND_WORDSPACE_AT_END_OF_BUFFER
# define OPTION_WINKEY_STRICT_HOST_OPEN // require an admin host open Winkey command before doing any other commands
//#define OPTION_WINKEY_EXTENDED_COMMANDS // in development
2014-03-05 00:58:02 +00:00
# define OPTION_WINKEY_SEND_BREAKIN_STATUS_BYTE // additional code to check_dit_paddle() and check_dah_paddle() to send 0xC2 status byte when paddles are hit
2013-08-29 01:35:16 +00:00
# define OPTION_WINKEY_INTERRUPTS_MEMORY_REPEAT
//#define OPTION_REVERSE_BUTTON_ORDER // This is mainly for the DJ0MY NanoKeyer http://nanokeyer.wordpress.com/
# define OPTION_PROG_MEM_TRIM_TRAILING_SPACES // trim trailing spaces from memory when programming in command mode
# define OPTION_DIT_PADDLE_NO_SEND_ON_MEM_RPT // this makes dit paddle memory interruption a little smoother
//#define OPTION_MORE_DISPLAY_MSGS // additional optional display messages - comment out to save memory
//#define OPTION_N1MM_WINKEY_TAB_BUG_WORKAROUND // enable this to ignore the TAB key in the Send CW window (this breaks SO2R functionality in N1MM)
//#define OPTION_WATCHDOG_TIMER // this enables a four second ATmega48/88/168/328 watchdog timer; use for unattended/remote operation only
//#define OPTION_MOUSE_MOVEMENT_PADDLE // experimental (just fooling around) - mouse movement will act like a paddle
2014-03-10 00:46:10 +00:00
# define OPTION_NON_ENGLISH_EXTENSIONS // add support for additional CW characters (i.e. À, Å, Þ, etc.)
2013-08-29 01:35:16 +00:00
//#define OPTION_PS2_NON_ENGLISH_CHAR_LCD_DISPLAY_SUPPORT // makes some non-English characters from the PS2 keyboard display correctly in the LCD display (donated by Marcin sp5iou)
2014-03-03 00:54:52 +00:00
//#define OPTION_KEEP_PTT_KEYED_WHEN_CHARS_BUFFERED // this option keeps PTT high if there are characters buffered from the keyboard, the serial interface, or Winkey
2014-03-10 00:46:10 +00:00
# define OPTION_DISPLAY_NON_ENGLISH_EXTENSIONS // LCD display suport for non-English (NO/DK/DE) characters - Courtesy of OZ1JHM
