kopia lustrzana https://github.com/projecthorus/horusdemodlib
119 wiersze
4.2 KiB
Bash
Executable File
119 wiersze
4.2 KiB
Bash
Executable File
#!/usr/bin/env bash
|
|
#
|
|
# Dual RTTY / Horus Binary Decoder Script
|
|
# Intended for use on Horus flights, with the following payload frequencies:
|
|
# RTTY: 434.650 MHz - Callsign 'HORUS'
|
|
# MFSK: 434.660 MHz - Callsign 'HORUSBINARY'
|
|
#
|
|
# The SDR is tuned 5 kHz below the RTTY frequency, and the frequency estimators are set across the two frequencies.
|
|
# Modem statistics are sent out via a new 'MODEM_STATS' UDP broadcast message every second.
|
|
#
|
|
|
|
# Change directory to the horusdemodlib directory.
|
|
# If running as a different user, you will need to change this line
|
|
cd /home/pi/horusdemodlib/
|
|
|
|
# Receive requency, in Hz. This is the frequency the SDR is tuned to.
|
|
RXFREQ=434645000
|
|
|
|
# Where in the passband we expect to find the RTTY signal, in Hz.
|
|
# For Horus flights, this is on 434.650 MHz, so with a SDR frequency of 434.645 MHz,
|
|
# we expect to find the RTTY signal at approx +5 kHz.
|
|
# Note that the signal must be located ABOVE the centre frequency of the receiver.
|
|
RTTY_SIGNAL=5000
|
|
|
|
# Where in the receiver passband we expect to find the Horus Binary (MFSK) signal, in Hz.
|
|
# For Horus flights, this is on 434.660 MHz, so with a SDR frequency of 434.645 MHz,
|
|
# we expect to find the RTTY signal at approx +15 kHz.
|
|
MFSK_SIGNAL=15000
|
|
|
|
# Frequency estimator bandwidth. The wider the bandwidth, the more drift and frequency error the modem can tolerate,
|
|
# but the higher the chance that the modem will lock on to a strong spurious signal.
|
|
RXBANDWIDTH=8000
|
|
|
|
# Receiver Gain. Set this to 0 to use automatic gain control, otherwise if running a
|
|
# preamplifier, you may want to experiment with different gain settings to optimize
|
|
# your receiver setup.
|
|
# You can find what gain range is valid for your RTLSDR by running: rtl_test
|
|
GAIN=0
|
|
|
|
# Bias Tee Enable (1) or Disable (0)
|
|
# NOTE: This uses the -T bias-tee option which is only available on recent versions
|
|
# of rtl-sdr. Check if your version has this option by running rtl_fm --help and looking
|
|
# for it in the option list.
|
|
# If not, you may need to uninstall that version, and then compile from source: https://github.com/osmocom/rtl-sdr
|
|
BIAS=0
|
|
|
|
# Receiver PPM offset
|
|
PPM=0
|
|
|
|
|
|
|
|
|
|
# Check that the horus_demod decoder has been compiled.
|
|
DECODER=./build/src/horus_demod
|
|
if [ -f "$DECODER" ]; then
|
|
echo "Found horus_demod."
|
|
else
|
|
echo "ERROR - $DECODER does not exist - have you compiled it yet?"
|
|
exit 1
|
|
fi
|
|
|
|
# Check that bc is available on the system path.
|
|
if echo "1+1" | bc > /dev/null; then
|
|
echo "Found bc."
|
|
else
|
|
echo "ERROR - Cannot find bc - Did you install it?"
|
|
exit 1
|
|
fi
|
|
|
|
# Use a local venv if it exists
|
|
VENV_DIR=venv
|
|
if [ -d "$VENV_DIR" ]; then
|
|
echo "Entering venv."
|
|
source $VENV_DIR/bin/activate
|
|
fi
|
|
|
|
|
|
# Calculate the frequency estimator limits
|
|
# Note - these are somewhat hard-coded for this dual-RX application.
|
|
RTTY_LOWER=$(echo "$RTTY_SIGNAL - $RXBANDWIDTH/2" | bc)
|
|
RTTY_UPPER=$(echo "$RTTY_SIGNAL + $RXBANDWIDTH/2" | bc)
|
|
RTTY_CENTRE=$(echo "$RXFREQ + $RTTY_SIGNAL" | bc)
|
|
|
|
MFSK_LOWER=$(echo "$MFSK_SIGNAL - $RXBANDWIDTH/2" | bc)
|
|
MFSK_UPPER=$(echo "$MFSK_SIGNAL + $RXBANDWIDTH/2" | bc)
|
|
MFSK_CENTRE=$(echo "$RXFREQ + $MFSK_SIGNAL" | bc)
|
|
|
|
echo "Using SDR Centre Frequency: $RXFREQ Hz."
|
|
echo "Using RTTY estimation range: $RTTY_LOWER - $RTTY_UPPER Hz"
|
|
echo "Using MFSK estimation range: $MFSK_LOWER - $MFSK_UPPER Hz"
|
|
|
|
BIAS_SETTING=""
|
|
|
|
if [ "$BIAS" = "1" ]; then
|
|
echo "Enabling Bias Tee."
|
|
BIAS_SETTING=" -T"
|
|
fi
|
|
|
|
GAIN_SETTING=""
|
|
if [ "$GAIN" = "0" ]; then
|
|
echo "Using AGC."
|
|
GAIN_SETTING=""
|
|
else
|
|
echo "Using Manual Gain"
|
|
GAIN_SETTING=" -g $GAIN"
|
|
fi
|
|
|
|
STATS_SETTING=""
|
|
|
|
if [ "$STATS_OUTPUT" = "1" ]; then
|
|
echo "Enabling Modem Statistics."
|
|
STATS_SETTING=" --stats=100"
|
|
fi
|
|
|
|
# Start the receive chain.
|
|
# Note that we now pass in the SDR centre frequency ($RXFREQ) and 'target' signal frequency ($RTTY_CENTRE / $MFSK_CENTRE)
|
|
# to enable providing additional metadata to Habitat / Sondehub.
|
|
rtl_fm -M raw -F9 -s 48000 -p $PPM $GAIN_SETTING$BIAS_SETTING -f $RXFREQ | tee >($DECODER -q --stats=5 -g -m RTTY --fsk_lower=$RTTY_LOWER --fsk_upper=$RTTY_UPPER - - | python -m horusdemodlib.uploader --rtty --freq_hz $RXFREQ --freq_target_hz $RTTY_CENTRE ) >($DECODER -q --stats=5 -g -m binary --fsk_lower=$MFSK_LOWER --fsk_upper=$MFSK_UPPER - - | python -m horusdemodlib.uploader --freq_hz $RXFREQ --freq_target_hz $MFSK_CENTRE ) > /dev/null
|