kopia lustrzana https://github.com/gnea/grbl
288 wiersze
11 KiB
C
288 wiersze
11 KiB
C
/*
|
|
cpu_map.h - CPU and pin mapping configuration file
|
|
Part of Grbl
|
|
|
|
Copyright (c) 2013-2014 Sungeun K. Jeon
|
|
|
|
Grbl is free software: you can redistribute it and/or modify
|
|
it under the terms of the GNU General Public License as published by
|
|
the Free Software Foundation, either version 3 of the License, or
|
|
(at your option) any later version.
|
|
|
|
Grbl is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
GNU General Public License for more details.
|
|
|
|
You should have received a copy of the GNU General Public License
|
|
along with Grbl. If not, see <http://www.gnu.org/licenses/>.
|
|
*/
|
|
|
|
/* The cpu_map.h file serves as a central pin mapping settings file for different processor
|
|
types, i.e. AVR 328p or AVR Mega 2560. Grbl officially supports the Arduino Uno, but the
|
|
other supplied pin mappings are supplied by users, so your results may vary. */
|
|
|
|
// NOTE: This is still a work in progress. We are still centralizing the configurations to
|
|
// this file, so your success may vary for other CPUs.
|
|
|
|
#ifndef cpu_map_h
|
|
#define cpu_map_h
|
|
|
|
#ifdef CPU_MAP_ATMEGA328P // (Arduino Uno) Officially supported by Grbl.
|
|
|
|
// Serial port pins
|
|
#define SERIAL_RX USART_RX_vect
|
|
#define SERIAL_UDRE USART_UDRE_vect
|
|
|
|
// Start of PWM & Stepper Enabled Spindle
|
|
// #define VARIABLE_SPINDLE // comment this out to disable PWM & Stepper on the spindle
|
|
|
|
// NOTE: All step bit and direction pins must be on the same port.
|
|
#define STEPPING_DDR DDRD
|
|
#define STEPPING_PORT PORTD
|
|
#define X_STEP_BIT 2 // Uno Digital Pin 2
|
|
#define Y_STEP_BIT 3 // Uno Digital Pin 3
|
|
#define Z_STEP_BIT 4 // Uno Digital Pin 4
|
|
#define STEP_MASK ((1<<X_STEP_BIT)|(1<<Y_STEP_BIT)|(1<<Z_STEP_BIT)) // All step bits
|
|
|
|
#define DIRECTION_DDR DDRD
|
|
#define DIRECTION_PORT PORTD
|
|
#define X_DIRECTION_BIT 5 // Uno Digital Pin 5
|
|
#define Y_DIRECTION_BIT 6 // Uno Digital Pin 6
|
|
#define Z_DIRECTION_BIT 7 // Uno Digital Pin 7
|
|
#define DIRECTION_MASK ((1<<X_DIRECTION_BIT)|(1<<Y_DIRECTION_BIT)|(1<<Z_DIRECTION_BIT)) // All direction bits
|
|
|
|
#define STEPPERS_DISABLE_DDR DDRB
|
|
#define STEPPERS_DISABLE_PORT PORTB
|
|
#define STEPPERS_DISABLE_BIT 0 // Uno Digital Pin 8
|
|
#define STEPPERS_DISABLE_MASK (1<<STEPPERS_DISABLE_BIT)
|
|
|
|
#ifdef VARIABLE_SPINDLE // Z LImit has been disabled to make room for the Spindle PWM
|
|
// NOTE: All limit bit pins must be on the same port
|
|
#define LIMIT_DDR DDRB
|
|
#define LIMIT_PIN PINB
|
|
#define LIMIT_PORT PORTB
|
|
#define X_LIMIT_BIT 1 // Uno Digital Pin 9
|
|
#define Y_LIMIT_BIT 2 // Uno Digital Pin 9
|
|
#define Z_LIMIT_BIT 2 // Uno Digital Pin 11
|
|
#define LIMIT_INT PCIE0 // Pin change interrupt enable pin
|
|
#define LIMIT_INT_vect PCINT0_vect
|
|
#define LIMIT_PCMSK PCMSK0 // Pin change interrupt register
|
|
#define LIMIT_MASK ((1<<X_LIMIT_BIT)|(1<<Y_LIMIT_BIT)) // All limit bits
|
|
|
|
#else
|
|
// NOTE: All limit bit pins must be on the same port
|
|
#define LIMIT_DDR DDRB
|
|
#define LIMIT_PIN PINB
|
|
#define LIMIT_PORT PORTB
|
|
#define X_LIMIT_BIT 1 // Uno Digital Pin 9
|
|
#define Y_LIMIT_BIT 2 // Uno Digital Pin 10
|
|
#define Z_LIMIT_BIT 3 // Uno Digital Pin 11
|
|
#define LIMIT_INT PCIE0 // Pin change interrupt enable pin
|
|
#define LIMIT_INT_vect PCINT0_vect
|
|
#define LIMIT_PCMSK PCMSK0 // Pin change interrupt register
|
|
#define LIMIT_MASK ((1<<X_LIMIT_BIT)|(1<<Y_LIMIT_BIT)|(1<<Z_LIMIT_BIT)) // All limit bits
|
|
#endif
|
|
|
|
// WARNING if INVERT_SPINDLE is defined the pin will be LOW(Active) on reset of controller until spindle_init() is called.
|
|
// this should only be a very short period of time but will energise the spindle.
|
|
// #define INVERT_SPINDLE // This will INVERT the Spindle LOW=Active
|
|
// END WARNING
|
|
|
|
#define SPINDLE_ENABLE_DDR DDRB
|
|
#define SPINDLE_ENABLE_PORT PORTB
|
|
#define SPINDLE_ENABLE_BIT 4 // Uno Digital Pin 12
|
|
|
|
#define SPINDLE_DIRECTION_DDR DDRB
|
|
#define SPINDLE_DIRECTION_PORT PORTB
|
|
#define SPINDLE_DIRECTION_BIT 5 // Uno Digital Pin 13 (NOTE: D13 can't be pulled-high input due to LED.)
|
|
|
|
// WARNING if INVERT_COOLANT is defined the pin will be LOW(Active) on reset of controller until coolant_init() is called.
|
|
// this should only be a very short period of time but will energise the coolant pump.
|
|
// #define INVERT_COOLANT // This will INVERT the Coolant LOW=Active
|
|
// END WARNING
|
|
|
|
#define COOLANT_FLOOD_DDR DDRC
|
|
#define COOLANT_FLOOD_PORT PORTC
|
|
#define COOLANT_FLOOD_BIT 3 // Uno Analog Pin 3
|
|
|
|
// NOTE: Uno analog pins 4 and 5 are reserved for an i2c interface, and may be installed at
|
|
// a later date if flash and memory space allows.
|
|
// #define ENABLE_M7 // Mist coolant disabled by default. Uncomment to enable.
|
|
#ifdef ENABLE_M7
|
|
#define COOLANT_MIST_DDR DDRC
|
|
#define COOLANT_MIST_PORT PORTC
|
|
#define COOLANT_MIST_BIT 4 // Uno Analog Pin 4
|
|
#endif
|
|
|
|
// NOTE: All pinouts pins must be on the same port, but cannot be on same port as limit pins.
|
|
#define PINOUT_DDR DDRC
|
|
#define PINOUT_PIN PINC
|
|
#define PINOUT_PORT PORTC
|
|
#define PIN_RESET 0 // Uno Analog Pin 0
|
|
#define PIN_FEED_HOLD 1 // Uno Analog Pin 1
|
|
#define PIN_CYCLE_START 2 // Uno Analog Pin 2
|
|
#define PINOUT_INT PCIE1 // Pin change interrupt enable pin
|
|
#define PINOUT_INT_vect PCINT1_vect
|
|
#define PINOUT_PCMSK PCMSK1 // Pin change interrupt register
|
|
#define PINOUT_MASK ((1<<PIN_RESET)|(1<<PIN_FEED_HOLD)|(1<<PIN_CYCLE_START))
|
|
|
|
#ifdef VARIABLE_SPINDLE
|
|
|
|
#define SPINDLE_IS_PWM // Uncomment this if your Spindle uses PWM ie. DC Motor
|
|
|
|
#ifdef SPINDLE_IS_PWM
|
|
#define SPINDLE_MAX_RPM 255 // Max RPM of your spindle - This value is equal to 100% Duty Cycle on the PWM
|
|
#endif
|
|
|
|
// Advanced Configuration Below You should not need to touch these variables
|
|
|
|
//Set Timer up to use TIMER4 OCR4B which is attached to Digital Pin 7
|
|
#define TCCRA_REGISTER TCCR2A
|
|
#define TCCRB_REGISTER TCCR2B
|
|
#define OCR_REGISTER OCR2A
|
|
|
|
#define COMB_BIT COM2A1
|
|
#define WAVE0_REGISTER WGM20
|
|
#define WAVE1_REGISTER WGM21
|
|
#define WAVE2_REGISTER WGM22
|
|
#define WAVE3_REGISTER WGM23
|
|
|
|
#define SPINDLE_PWM_DDR DDRB
|
|
#define SPINDLE_PWM_PORT PORTB
|
|
#define SPINDLE_PWM_BIT 3 // UNO Digital Pin 11
|
|
|
|
#endif // End of VARIABLE_SPINDLE
|
|
#endif
|
|
|
|
|
|
#ifdef CPU_MAP_ATMEGA2560 // (Arduino Mega 2560) Working @EliteEng
|
|
|
|
// Serial port pins
|
|
#define SERIAL_RX USART0_RX_vect
|
|
#define SERIAL_UDRE USART0_UDRE_vect
|
|
|
|
// Increase Buffers to make use of extra SRAM
|
|
//#define RX_BUFFER_SIZE 256
|
|
//#define TX_BUFFER_SIZE 128
|
|
//#define BLOCK_BUFFER_SIZE 36
|
|
//#define LINE_BUFFER_SIZE 100
|
|
|
|
// NOTE: All step pins must be on the same port.
|
|
#define STEPPING_DDR DDRA
|
|
#define STEPPING_PORT PORTA
|
|
#define STEPPING_PIN PINA
|
|
#define X_STEP_BIT 2 // MEGA2560 Digital Pin 24
|
|
#define Y_STEP_BIT 3 // MEGA2560 Digital Pin 25
|
|
#define Z_STEP_BIT 4 // MEGA2560 Digital Pin 26
|
|
#define STEP_MASK ((1<<X_STEP_BIT)|(1<<Y_STEP_BIT)|(1<<Z_STEP_BIT)) // All step bits
|
|
|
|
// NOTE: All direction pins must be on the same port.
|
|
#define DIRECTION_DDR DDRA
|
|
#define DIRECTION_PORT PORTA
|
|
#define DIRECTION_PIN PINA
|
|
#define X_DIRECTION_BIT 5 // MEGA2560 Digital Pin 27
|
|
#define Y_DIRECTION_BIT 6 // MEGA2560 Digital Pin 28
|
|
#define Z_DIRECTION_BIT 7 // MEGA2560 Digital Pin 29
|
|
#define DIRECTION_MASK ((1<<X_DIRECTION_BIT)|(1<<Y_DIRECTION_BIT)|(1<<Z_DIRECTION_BIT)) // All direction bits
|
|
|
|
#define STEPPERS_DISABLE_DDR DDRB
|
|
#define STEPPERS_DISABLE_PORT PORTB
|
|
#define STEPPERS_DISABLE_BIT 7 // MEGA2560 Digital Pin 13
|
|
#define STEPPERS_DISABLE_MASK (1<<STEPPERS_DISABLE_BIT)
|
|
|
|
// NOTE: All limit bit pins must be on the same port
|
|
#define LIMIT_DDR DDRB
|
|
#define LIMIT_PORT PORTB
|
|
#define LIMIT_PIN PINB
|
|
#define X_LIMIT_BIT 4 // MEGA2560 Digital Pin 10
|
|
#define Y_LIMIT_BIT 5 // MEGA2560 Digital Pin 11
|
|
#define Z_LIMIT_BIT 6 // MEGA2560 Digital Pin 12
|
|
#define LIMIT_INT PCIE0 // Pin change interrupt enable pin
|
|
#define LIMIT_INT_vect PCINT0_vect
|
|
#define LIMIT_PCMSK PCMSK0 // Pin change interrupt register
|
|
#define LIMIT_MASK ((1<<X_LIMIT_BIT)|(1<<Y_LIMIT_BIT)|(1<<Z_LIMIT_BIT)) // All limit bits
|
|
|
|
// WARNING if INVERT_SPINDLE is defined the pin will be LOW(Active) on reset of controller until spindle_init() is called.
|
|
// this should only be a very short period of time but will energise the spindle.
|
|
// #define INVERT_SPINDLE // This will INVERT the Spindle LOW=Active
|
|
// END WARNING
|
|
|
|
#define SPINDLE_ENABLE_DDR DDRH
|
|
#define SPINDLE_ENABLE_PORT PORTH
|
|
#define SPINDLE_ENABLE_BIT 3 // MEGA2560 Digital Pin 6
|
|
|
|
#define SPINDLE_DIRECTION_DDR DDRE
|
|
#define SPINDLE_DIRECTION_PORT PORTE
|
|
#define SPINDLE_DIRECTION_BIT 3 // MEGA2560 Digital Pin 5
|
|
|
|
// WARNING if INVERT_COOLANT is defined the pin will be LOW(Active) on reset of controller until coolant_init() is called.
|
|
// this should only be a very short period of time but will energise the coolant pump.
|
|
// #define INVERT_COOLANT // This will INVERT the Coolant LOW=Active
|
|
// END WARNING
|
|
|
|
#define COOLANT_FLOOD_DDR DDRH
|
|
#define COOLANT_FLOOD_PORT PORTH
|
|
#define COOLANT_FLOOD_BIT 5 // MEGA2560 Digital Pin 8
|
|
|
|
// #define ENABLE_M7 // Mist coolant disabled by default. Uncomment to enable.
|
|
#ifdef ENABLE_M7
|
|
#define COOLANT_MIST_DDR DDRH
|
|
#define COOLANT_MIST_PORT PORTH
|
|
#define COOLANT_MIST_BIT 6 // MEGA2560 Digital Pin 9
|
|
#endif
|
|
|
|
// NOTE: All pinouts pins must be on the same port and cannot be on same port as limit pins.
|
|
#define PINOUT_DDR DDRK
|
|
#define PINOUT_PIN PINK
|
|
#define PINOUT_PORT PORTK
|
|
#define PIN_RESET 0 // MEGA2560 Analog Pin 8
|
|
#define PIN_FEED_HOLD 1 // MEGA2560 Analog Pin 9
|
|
#define PIN_CYCLE_START 2 // MEGA2560 Analog Pin 10
|
|
#define PINOUT_INT PCIE2 // Pin change interrupt enable pin
|
|
#define PINOUT_INT_vect PCINT2_vect
|
|
#define PINOUT_PCMSK PCMSK2 // Pin change interrupt register
|
|
#define PINOUT_MASK ((1<<PIN_RESET)|(1<<PIN_FEED_HOLD)|(1<<PIN_CYCLE_START))
|
|
|
|
// Start of PWM & Stepper Enabled Spindle
|
|
// #define VARIABLE_SPINDLE // comment this out to disable PWM & Stepper on the spindle
|
|
#ifdef VARIABLE_SPINDLE
|
|
|
|
//#define SPINDLE_IS_STEPPER // Uncomment this if your Spindle is a Stepper Motor
|
|
#define SPINDLE_IS_PWM // Uncomment this if your Spindle uses PWM ie. DC Motor
|
|
|
|
#ifdef SPINDLE_IS_PWM
|
|
#define SPINDLE_MAX_RPM 255 // Max RPM of your spindle
|
|
#endif
|
|
|
|
// Advanced Configuration Below You should not need to touch these variables
|
|
|
|
//Set Timer up to use TIMER4 OCR4B which is attached to Digital Pin 7
|
|
#define TCCRA_REGISTER TCCR2A
|
|
#define TCCRB_REGISTER TCCR2B
|
|
#define OCR_REGISTER OCR2B
|
|
|
|
#define COMB_BIT COM2B1
|
|
#define WAVE0_REGISTER WGM20
|
|
#define WAVE1_REGISTER WGM21
|
|
#define WAVE2_REGISTER WGM22
|
|
#define WAVE3_REGISTER WGM23
|
|
|
|
#define SPINDLE_PWM_DDR DDRH
|
|
#define SPINDLE_PWM_PORT PORTH
|
|
#define SPINDLE_PWM_BIT 6 // MEGA2560 Digital Pin 9
|
|
|
|
#endif // End of VARIABLE_SPINDLE
|
|
#endif
|
|
|
|
/*
|
|
#ifdef CPU_MAP_CUSTOM_PROC
|
|
// For a custom pin map or different processor, copy and paste one of the default cpu map
|
|
|
|
// settings above and modify it to your needs. Then, make sure the defined name is also
|
|
// changed in the config.h file.
|
|
#endif
|
|
*/
|
|
|
|
#endif
|