kopia lustrzana https://github.com/alanesq/esp32cam-demo
1354 wiersze
56 KiB
C++
1354 wiersze
56 KiB
C++
/*******************************************************************************************************************
|
|
*
|
|
* ESP32Cam development board demo sketch using Arduino IDE or PlatformIO
|
|
* Github: https://github.com/alanesq/ESP32Cam-demo
|
|
*
|
|
* Tested with ESP32 board manager version 1.0.6
|
|
*
|
|
* Starting point sketch for projects using the esp32cam development board with the following features
|
|
* web server with live video streaming and RGB data from camera demonstrated.
|
|
* sd card support using 1-bit mode (data pins are usually 2,4,12&13 but using 1bit mode only uses pin 2)
|
|
* flash led is still available for use (pin 4) and does not flash when accessing sd card
|
|
* Stores image in Spiffs if no sd card present
|
|
* PWM control of the illumination/flash LED
|
|
*
|
|
* GPIO:
|
|
* You can use io pins 13 and 12 for input or output (but 12 must not be high at boot)
|
|
* pin 16 is used for psram but you may get away with using it as input for a button but not recommended
|
|
* You could also use pins 1 & 3 if you do not use Serial (disable serialDebug in the settings below)
|
|
* Pins 14, 2 & 15 should be ok to use if you are not using an SD Card
|
|
* More info: https://randomnerdtutorials.com/esp32-cam-ai-thinker-pinout/
|
|
*
|
|
* You can use a MCP23017 io expander chip to give 16 gpio lines by enabling 'useMCP23017' in the setup section and connecting
|
|
* the i2c pins to 12 and 13 on the esp32cam module. Note: this requires the adafruit MCP23017 library to be installed.
|
|
*
|
|
* Created using the Arduino IDE with ESP32 module installed, no additional libraries required
|
|
* ESP32 support for Arduino IDE: https://raw.githubusercontent.com/espressif/arduino-esp32/gh-pages/package_esp32_index.json
|
|
*
|
|
* Info on the esp32cam board: https://randomnerdtutorials.com/esp32-cam-video-streaming-face-recognition-arduino-ide/
|
|
* https://github.com/espressif/esp32-camera
|
|
*
|
|
* To see a more advanced sketch along the same format as this one have a look at https://github.com/alanesq/CameraWifiMotion
|
|
* which includes email support, FTP, OTA updates and motion detection
|
|
*
|
|
* Sending image to TFT display see: https://www.survivingwithandroid.com/esp32-cam-tft-display-picture-st7735/
|
|
*
|
|
* esp32cam-demo is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the
|
|
* implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
|
|
*
|
|
*
|
|
*******************************************************************************************************************/
|
|
|
|
#if !defined ESP32
|
|
#error This sketch is only for an ESP32Cam module
|
|
#endif
|
|
|
|
|
|
// ---------------------------------------------------------------------------------------------------------
|
|
|
|
|
|
// Wifi Settings - uncomment and set here if not stored in platformio.ini
|
|
|
|
// #define SSID_NAME "Wifi SSID"
|
|
// #define SSID_PASWORD "wifi password"
|
|
|
|
|
|
// ---------------------------------------------------------------------------------------------------------
|
|
|
|
|
|
// Required by PlatformIO
|
|
|
|
#include <Arduino.h>
|
|
|
|
// forward declarations
|
|
bool initialiseCamera();
|
|
bool cameraImageSettings();
|
|
String localTime();
|
|
void flashLED(int reps);
|
|
byte storeImage();
|
|
void handleRoot();
|
|
void handlePhoto();
|
|
bool handleImg();
|
|
void handleNotFound();
|
|
void readRGBImage();
|
|
bool getNTPtime(int sec);
|
|
bool handleJPG();
|
|
void handleStream();
|
|
int requestWebPage(String*, String*, int);
|
|
void handleTest();
|
|
void brightLed(byte ledBrightness);
|
|
|
|
|
|
// ---------------------------------------------------------------
|
|
|
|
|
|
#include "esp_camera.h" // https://github.com/espressif/esp32-camera
|
|
// #include "camera_pins.h"
|
|
#include <base64.h> // for encoding buffer to display image on page
|
|
#include <WiFi.h>
|
|
#include <WebServer.h>
|
|
#include <HTTPClient.h>
|
|
#include "driver/ledc.h" // used to configure pwm on illumination led
|
|
|
|
// spiffs used to store images if no sd card present
|
|
#include <SPIFFS.h>
|
|
#include <FS.h> // gives file access on spiffs
|
|
|
|
|
|
// ---------------------------------------------------------------
|
|
// -SETTINGS
|
|
// ---------------------------------------------------------------
|
|
|
|
const char* stitle = "ESP32Cam-demo"; // title of this sketch
|
|
const char* sversion = "17Jan22"; // Sketch version
|
|
|
|
bool sendRGBfile = 0; // if set '/rgb' will send the rgb data as a file rather than display a HTML page
|
|
|
|
const bool serialDebug = 1; // show debug info. on serial port (1=enabled, disable if using pins 1 and 3 as gpio)
|
|
|
|
#define useMCP23017 0 // if MCP23017 IO expander chip is being used (on pins 12 and 13)
|
|
|
|
// Camera related
|
|
const bool flashRequired = 1; // If flash to be used when capturing image (1 = yes)
|
|
const framesize_t FRAME_SIZE_IMAGE = FRAMESIZE_VGA; // Image resolution:
|
|
// default = "const framesize_t FRAME_SIZE_IMAGE = FRAMESIZE_VGA"
|
|
// 160x120 (QQVGA), 128x160 (QQVGA2), 176x144 (QCIF), 240x176 (HQVGA),
|
|
// 320x240 (QVGA), 400x296 (CIF), 640x480 (VGA, default), 800x600 (SVGA),
|
|
// 1024x768 (XGA), 1280x1024 (SXGA), 1600x1200 (UXGA)
|
|
#define PIXFORMAT PIXFORMAT_JPEG; // image format, Options = YUV422, GRAYSCALE, RGB565, JPEG, RGB888
|
|
int cameraImageExposure = 0; // Camera exposure (0 - 1200) If gain and exposure both set to zero then auto adjust is enabled
|
|
int cameraImageGain = 0; // Image gain (0 - 30)
|
|
|
|
const int TimeBetweenStatus = 600; // speed of flashing system running ok status light (milliseconds)
|
|
|
|
const int indicatorLED = 33; // onboard small LED pin (33)
|
|
|
|
// Bright LED
|
|
const int brightLED = 4; // onboard Illumination/flash LED pin (4)
|
|
int brightLEDbrightness = 0; // initial brightness (0 - 255)
|
|
const int ledFreq = 5000; // PWM settings
|
|
const int ledChannel = 15; // needs to be 14 or 15 with esp32cam (timer3?)
|
|
const int ledRresolution = 8;
|
|
|
|
const int iopinA = 13; // general io pin 13
|
|
const int iopinB = 12; // general io pin 12 (must not be high at boot)
|
|
const int iopinC = 16; // input only pin 16 (used by PSRam but you may get away with using it for a button)
|
|
|
|
const int serialSpeed = 115200; // Serial data speed to use
|
|
|
|
// NTP - Internet time
|
|
const char* ntpServer = "pool.ntp.org";
|
|
const char* TZ_INFO = "GMT+0BST-1,M3.5.0/01:00:00,M10.5.0/02:00:00"; // enter your time zone (https://remotemonitoringsystems.ca/time-zone-abbreviations.php)
|
|
long unsigned lastNTPtime;
|
|
tm timeinfo;
|
|
time_t now;
|
|
|
|
// camera settings (for the standard - OV2640 - CAMERA_MODEL_AI_THINKER)
|
|
// see: https://randomnerdtutorials.com/esp32-cam-camera-pin-gpios/
|
|
// set camera resolution etc. in 'initialiseCamera()' and 'cameraImageSettings()'
|
|
#define CAMERA_MODEL_AI_THINKER
|
|
#define PWDN_GPIO_NUM 32 // power to camera (on/off)
|
|
#define RESET_GPIO_NUM -1 // -1 = not used
|
|
#define XCLK_GPIO_NUM 0
|
|
#define SIOD_GPIO_NUM 26 // i2c sda
|
|
#define SIOC_GPIO_NUM 27 // i2c scl
|
|
#define Y9_GPIO_NUM 35
|
|
#define Y8_GPIO_NUM 34
|
|
#define Y7_GPIO_NUM 39
|
|
#define Y6_GPIO_NUM 36
|
|
#define Y5_GPIO_NUM 21
|
|
#define Y4_GPIO_NUM 19
|
|
#define Y3_GPIO_NUM 18
|
|
#define Y2_GPIO_NUM 5
|
|
#define VSYNC_GPIO_NUM 25 // vsync_pin
|
|
#define HREF_GPIO_NUM 23 // href_pin
|
|
#define PCLK_GPIO_NUM 22 // pixel_clock_pin
|
|
|
|
|
|
|
|
// ******************************************************************************************************************
|
|
|
|
|
|
WebServer server(80); // serve web pages on port 80
|
|
|
|
// Used to disable brownout detection
|
|
#include "soc/soc.h"
|
|
#include "soc/rtc_cntl_reg.h"
|
|
|
|
// sd-card
|
|
#include "SD_MMC.h" // sd card - see https://randomnerdtutorials.com/esp32-cam-take-photo-save-microsd-card/
|
|
#include <SPI.h>
|
|
#include <FS.h> // gives file access
|
|
#define SD_CS 5 // sd chip select pin = 5
|
|
|
|
// MCP23017 IO expander on pins 12 and 13 (optional)
|
|
#if useMCP23017 == 1
|
|
#include <Wire.h>
|
|
#include "Adafruit_MCP23017.h"
|
|
Adafruit_MCP23017 mcp;
|
|
// Wire.setClock(1700000); // set frequency to 1.7mhz
|
|
#endif
|
|
|
|
// Define some global variables:
|
|
uint32_t lastStatus = millis(); // last time status light changed status (to flash all ok led)
|
|
bool sdcardPresent; // flag if an sd card is detected
|
|
int imageCounter; // image file name on sd card counter
|
|
String spiffsFilename = "/image.jpg"; // image name to use when storing in spiffs
|
|
|
|
|
|
|
|
// ******************************************************************************************************************
|
|
|
|
|
|
// ---------------------------------------------------------------
|
|
// -SETUP SETUP SETUP SETUP SETUP SETUP
|
|
// ---------------------------------------------------------------
|
|
|
|
void setup() {
|
|
|
|
if (serialDebug) {
|
|
Serial.begin(serialSpeed); // Start serial communication
|
|
// Serial.setDebugOutput(true);
|
|
|
|
Serial.println("\n\n\n"); // line feeds
|
|
Serial.println("-----------------------------------");
|
|
Serial.printf("Starting - %s - %s \n", stitle, sversion);
|
|
Serial.println("-----------------------------------");
|
|
// Serial.print("Reset reason: " + ESP.getResetReason());
|
|
}
|
|
|
|
WRITE_PERI_REG(RTC_CNTL_BROWN_OUT_REG, 0); // Turn-off the 'brownout detector'
|
|
|
|
// small indicator led on rear of esp32cam board
|
|
pinMode(indicatorLED, OUTPUT);
|
|
digitalWrite(indicatorLED,HIGH);
|
|
|
|
// Connect to wifi
|
|
digitalWrite(indicatorLED,LOW); // small indicator led on
|
|
if (serialDebug) {
|
|
Serial.print("\nConnecting to ");
|
|
Serial.print(SSID_NAME);
|
|
Serial.print("\n ");
|
|
}
|
|
WiFi.begin(SSID_NAME, SSID_PASWORD);
|
|
while (WiFi.status() != WL_CONNECTED) {
|
|
delay(500);
|
|
if (serialDebug) Serial.print(".");
|
|
}
|
|
if (serialDebug) {
|
|
Serial.print("\nWiFi connected, ");
|
|
Serial.print("IP address: ");
|
|
Serial.println(WiFi.localIP());
|
|
}
|
|
server.begin(); // start web server
|
|
digitalWrite(indicatorLED,HIGH); // small indicator led off
|
|
|
|
// define the web pages (i.e. call these procedures when url is requested)
|
|
server.on("/", handleRoot); // root page
|
|
server.on("/jpg", handleJPG); // capture image and send as jpg
|
|
server.on("/stream", handleStream); // stream live video
|
|
server.on("/photo", handlePhoto); // save image to sd card
|
|
server.on("/img", handleImg); // show image from sd card
|
|
server.on("/rgb", readRGBImage); // demo converting image to RGB
|
|
server.on("/test", handleTest); // Testing procedure
|
|
server.onNotFound(handleNotFound); // invalid url requested
|
|
|
|
// NTP - internet time
|
|
if (serialDebug) Serial.println("\nGetting real time (NTP)");
|
|
configTime(0, 0, ntpServer);
|
|
setenv("TZ", TZ_INFO, 1);
|
|
if (getNTPtime(10)) { // wait up to 10 sec to sync
|
|
} else {
|
|
if (serialDebug) Serial.println("Time not set");
|
|
}
|
|
lastNTPtime = time(&now);
|
|
|
|
// set up camera
|
|
if (serialDebug) Serial.print(("\nInitialising camera: "));
|
|
if (initialiseCamera()) {
|
|
if (serialDebug) Serial.println("OK");
|
|
}
|
|
else {
|
|
if (serialDebug) Serial.println("failed");
|
|
}
|
|
|
|
// Spiffs - for storing images without an sd card
|
|
// see: https://circuits4you.com/2018/01/31/example-of-esp8266-flash-file-system-spiffs/
|
|
if (!SPIFFS.begin(true)) {
|
|
if (serialDebug) Serial.println(("An Error has occurred while mounting SPIFFS - restarting"));
|
|
delay(5000);
|
|
ESP.restart(); // restart and try again
|
|
delay(5000);
|
|
} else {
|
|
// SPIFFS.format(); // wipe spiffs
|
|
if (serialDebug) {
|
|
Serial.print(("SPIFFS mounted successfully: "));
|
|
Serial.printf("total bytes: %d , used: %d \n", SPIFFS.totalBytes(), SPIFFS.usedBytes());
|
|
}
|
|
}
|
|
|
|
// SD Card - if one is detected set 'sdcardPresent' High
|
|
if (!SD_MMC.begin("/sdcard", true)) { // if loading sd card fails
|
|
// note: ('/sdcard", true)' = 1bit mode - see: https://www.reddit.com/r/esp32/comments/d71es9/a_breakdown_of_my_experience_trying_to_talk_to_an/
|
|
if (serialDebug) Serial.println("No SD Card detected");
|
|
sdcardPresent = 0; // flag no sd card available
|
|
} else {
|
|
uint8_t cardType = SD_MMC.cardType();
|
|
if (cardType == CARD_NONE) { // if invalid card found
|
|
if (serialDebug) Serial.println("SD Card type detect failed");
|
|
sdcardPresent = 0; // flag no sd card available
|
|
} else {
|
|
// valid sd card detected
|
|
uint16_t SDfreeSpace = (uint64_t)(SD_MMC.totalBytes() - SD_MMC.usedBytes()) / (1024 * 1024);
|
|
if (serialDebug) Serial.printf("SD Card found, free space = %dMB \n", SDfreeSpace);
|
|
sdcardPresent = 1; // flag sd card available
|
|
}
|
|
}
|
|
fs::FS &fs = SD_MMC; // sd card file system
|
|
|
|
// discover the number of image files already stored in '/img' folder of the sd card and set image file counter accordingly
|
|
imageCounter = 0;
|
|
if (sdcardPresent) {
|
|
int tq=fs.mkdir("/img"); // create the '/img' folder on sd card (in case it is not already there)
|
|
if (!tq) {
|
|
if (serialDebug) Serial.println("Unable to create IMG folder on sd card");
|
|
}
|
|
|
|
// open the image folder and step through all files in it
|
|
File root = fs.open("/img");
|
|
while (true)
|
|
{
|
|
File entry = root.openNextFile(); // open next file in the folder
|
|
if (!entry) break; // if no more files in the folder
|
|
imageCounter ++; // increment image counter
|
|
entry.close();
|
|
}
|
|
root.close();
|
|
if (serialDebug) Serial.printf("Image file count = %d \n",imageCounter);
|
|
}
|
|
|
|
// define i/o pins
|
|
pinMode(indicatorLED, OUTPUT); // defined again as sd card config can reset it
|
|
digitalWrite(indicatorLED,HIGH); // led off = High
|
|
pinMode(iopinA, OUTPUT); // pin 13 - free io pin, can be used for input or output
|
|
pinMode(iopinB, OUTPUT); // pin 12 - free io pin, can be used for input or output (must not be high at boot)
|
|
pinMode(iopinC, INPUT); // pin 16 - free input only pin (may cause issues?)
|
|
|
|
// MCP23017 io expander (requires adafruit MCP23017 library)
|
|
#if useMCP23017 == 1
|
|
Wire.begin(12,13); // use pins 12 and 13 for i2c
|
|
mcp.begin(&Wire); // use default address 0
|
|
mcp.pinMode(0, OUTPUT); // Define GPA0 (physical pin 21) as output pin
|
|
mcp.pinMode(8, INPUT); // Define GPB0 (physical pin 1) as input pin
|
|
mcp.pullUp(8, HIGH); // turn on a 100K pullup internally
|
|
// change pin state with mcp.digitalWrite(0, HIGH);
|
|
// read pin state with mcp.digitalRead(8)
|
|
#endif
|
|
|
|
// set up illumination LED (flash)
|
|
ledcSetup(ledChannel, ledFreq, ledRresolution);
|
|
ledcAttachPin(brightLED, ledChannel);
|
|
brightLed(0); // change bright LED
|
|
|
|
// startup complete
|
|
if (serialDebug) Serial.println("\nStarted...");
|
|
flashLED(2); // flash the onboard indicator led
|
|
brightLed(64); // change bright LED
|
|
delay(200);
|
|
brightLed(0); // change bright LED
|
|
|
|
} // setup
|
|
|
|
|
|
// change illumination LED brightness
|
|
void brightLed(byte ledBrightness){
|
|
brightLEDbrightness = ledBrightness; // store setting
|
|
ledcWrite(ledChannel, ledBrightness); // change LED brightness (0 - 255)
|
|
if (serialDebug) Serial.println("Brightness changed to " + String(ledBrightness) );
|
|
}
|
|
|
|
|
|
// ******************************************************************************************************************
|
|
|
|
|
|
// ----------------------------------------------------------------
|
|
// -LOOP LOOP LOOP LOOP LOOP LOOP LOOP
|
|
// ----------------------------------------------------------------
|
|
|
|
|
|
void loop() {
|
|
|
|
server.handleClient(); // handle any incoming web page requests
|
|
|
|
|
|
|
|
|
|
|
|
|
|
// <<< YOUR CODE HERE >>>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
// // Capture an image and save to sd card every 5 seconds (i.e. time lapse)
|
|
// static uint32_t lastCamera = millis();
|
|
// if ( ((unsigned long)(millis() - lastCamera) >= 5000) && sdcardPresent ) {
|
|
// lastCamera = millis(); // reset timer
|
|
// storeImage(); // save an image to sd card
|
|
// if (serialDebug) Serial.println("Time lapse image captured");
|
|
// }
|
|
|
|
// flash status LED to show sketch is running ok
|
|
if ((unsigned long)(millis() - lastStatus) >= TimeBetweenStatus) {
|
|
lastStatus = millis(); // reset timer
|
|
digitalWrite(indicatorLED,!digitalRead(indicatorLED)); // flip indicator led status
|
|
}
|
|
|
|
} // loop
|
|
|
|
|
|
|
|
// ******************************************************************************************************************
|
|
|
|
|
|
// ----------------------------------------------------------------
|
|
// Initialise the camera
|
|
// ----------------------------------------------------------------
|
|
// returns TRUE if successful
|
|
|
|
bool initialiseCamera() {
|
|
|
|
camera_config_t config;
|
|
config.ledc_channel = LEDC_CHANNEL_0;
|
|
config.ledc_timer = LEDC_TIMER_0;
|
|
config.pin_d0 = Y2_GPIO_NUM;
|
|
config.pin_d1 = Y3_GPIO_NUM;
|
|
config.pin_d2 = Y4_GPIO_NUM;
|
|
config.pin_d3 = Y5_GPIO_NUM;
|
|
config.pin_d4 = Y6_GPIO_NUM;
|
|
config.pin_d5 = Y7_GPIO_NUM;
|
|
config.pin_d6 = Y8_GPIO_NUM;
|
|
config.pin_d7 = Y9_GPIO_NUM;
|
|
config.pin_xclk = XCLK_GPIO_NUM;
|
|
config.pin_pclk = PCLK_GPIO_NUM;
|
|
config.pin_vsync = VSYNC_GPIO_NUM;
|
|
config.pin_href = HREF_GPIO_NUM;
|
|
config.pin_sscb_sda = SIOD_GPIO_NUM;
|
|
config.pin_sscb_scl = SIOC_GPIO_NUM;
|
|
config.pin_pwdn = PWDN_GPIO_NUM;
|
|
config.pin_reset = RESET_GPIO_NUM;
|
|
config.xclk_freq_hz = 20000000; // XCLK 20MHz or 10MHz for OV2640 double FPS (Experimental)
|
|
config.pixel_format = PIXFORMAT; // Options = YUV422, GRAYSCALE, RGB565, JPEG, RGB888
|
|
config.frame_size = FRAME_SIZE_IMAGE; // Image sizes: 160x120 (QQVGA), 128x160 (QQVGA2), 176x144 (QCIF), 240x176 (HQVGA), 320x240 (QVGA),
|
|
// 400x296 (CIF), 640x480 (VGA, default), 800x600 (SVGA), 1024x768 (XGA), 1280x1024 (SXGA),
|
|
// 1600x1200 (UXGA)
|
|
config.jpeg_quality = 10; // 0-63 lower number means higher quality
|
|
config.fb_count = 1; // if more than one, i2s runs in continuous mode. Use only with JPEG
|
|
|
|
// check the esp32cam board has a psram chip installed (extra memory used for storing captured images)
|
|
// Note: if not using "AI thinker esp32 cam" in the Arduino IDE, SPIFFS must be enabled
|
|
if (!psramFound()) {
|
|
if (serialDebug) Serial.println("Warning: No PSRam found so defaulting to image size 'CIF'");
|
|
config.frame_size = FRAMESIZE_CIF;
|
|
}
|
|
|
|
//#if defined(CAMERA_MODEL_ESP_EYE)
|
|
// pinMode(13, INPUT_PULLUP);
|
|
// pinMode(14, INPUT_PULLUP);
|
|
//#endif
|
|
|
|
esp_err_t camerr = esp_camera_init(&config); // initialise the camera
|
|
if (camerr != ESP_OK) {
|
|
if (serialDebug) Serial.printf("ERROR: Camera init failed with error 0x%x", camerr);
|
|
}
|
|
|
|
cameraImageSettings(); // apply custom camera settings
|
|
|
|
return (camerr == ESP_OK); // return boolean result of camera initialisation
|
|
}
|
|
|
|
|
|
// ******************************************************************************************************************
|
|
|
|
|
|
// ----------------------------------------------------------------
|
|
// -Change camera image settings
|
|
// ----------------------------------------------------------------
|
|
// Adjust image properties (brightness etc.)
|
|
// Defaults to auto adjustments if exposure and gain are both set to zero
|
|
// - Returns TRUE if successful
|
|
// BTW - some interesting info on exposure times here: https://github.com/raduprv/esp32-cam_ov2640-timelapse
|
|
|
|
bool cameraImageSettings() {
|
|
|
|
if (serialDebug) Serial.println("Applying camera settings");
|
|
|
|
sensor_t *s = esp_camera_sensor_get();
|
|
// something to try?: if (s->id.PID == OV3660_PID)
|
|
if (s == NULL) {
|
|
if (serialDebug) Serial.println("Error: problem reading camera sensor settings");
|
|
return 0;
|
|
}
|
|
|
|
// if both set to zero enable auto adjust
|
|
if (cameraImageExposure == 0 && cameraImageGain == 0) {
|
|
// enable auto adjust
|
|
s->set_gain_ctrl(s, 1); // auto gain on
|
|
s->set_exposure_ctrl(s, 1); // auto exposure on
|
|
s->set_awb_gain(s, 1); // Auto White Balance enable (0 or 1)
|
|
} else {
|
|
// Apply manual settings
|
|
s->set_gain_ctrl(s, 0); // auto gain off
|
|
s->set_awb_gain(s, 1); // Auto White Balance enable (0 or 1)
|
|
s->set_exposure_ctrl(s, 0); // auto exposure off
|
|
s->set_agc_gain(s, cameraImageGain); // set gain manually (0 - 30)
|
|
s->set_aec_value(s, cameraImageExposure); // set exposure manually (0-1200)
|
|
}
|
|
|
|
return 1;
|
|
} // cameraImageSettings
|
|
|
|
|
|
// // More camera settings available:
|
|
// // If you enable gain_ctrl or exposure_ctrl it will prevent a lot of the other settings having any effect
|
|
// // more info on settings here: https://randomnerdtutorials.com/esp32-cam-ov2640-camera-settings/
|
|
// s->set_gain_ctrl(s, 0); // auto gain off (1 or 0)
|
|
// s->set_exposure_ctrl(s, 0); // auto exposure off (1 or 0)
|
|
// s->set_agc_gain(s, cameraImageGain); // set gain manually (0 - 30)
|
|
// s->set_aec_value(s, cameraImageExposure); // set exposure manually (0-1200)
|
|
// s->set_vflip(s, cameraImageInvert); // Invert image (0 or 1)
|
|
// s->set_quality(s, 10); // (0 - 63)
|
|
// s->set_gainceiling(s, GAINCEILING_32X); // Image gain (GAINCEILING_x2, x4, x8, x16, x32, x64 or x128)
|
|
// s->set_brightness(s, cameraImageBrightness); // (-2 to 2) - set brightness
|
|
// s->set_lenc(s, 1); // lens correction? (1 or 0)
|
|
// s->set_saturation(s, 0); // (-2 to 2)
|
|
// s->set_contrast(s, cameraImageContrast); // (-2 to 2)
|
|
// s->set_sharpness(s, 0); // (-2 to 2)
|
|
// s->set_hmirror(s, 0); // (0 or 1) flip horizontally
|
|
// s->set_colorbar(s, 0); // (0 or 1) - show a testcard
|
|
// s->set_special_effect(s, 0); // (0 to 6?) apply special effect
|
|
// s->set_whitebal(s, 0); // white balance enable (0 or 1)
|
|
// s->set_awb_gain(s, 1); // Auto White Balance enable (0 or 1)
|
|
// s->set_wb_mode(s, 0); // 0 to 4 - if awb_gain enabled (0 - Auto, 1 - Sunny, 2 - Cloudy, 3 - Office, 4 - Home)
|
|
// s->set_dcw(s, 0); // downsize enable? (1 or 0)?
|
|
// s->set_raw_gma(s, 1); // (1 or 0)
|
|
// s->set_aec2(s, 0); // automatic exposure sensor? (0 or 1)
|
|
// s->set_ae_level(s, 0); // auto exposure levels (-2 to 2)
|
|
// s->set_bpc(s, 0); // black pixel correction
|
|
// s->set_wpc(s, 0); // white pixel correction
|
|
|
|
|
|
// ******************************************************************************************************************
|
|
|
|
|
|
// ----------------------------------------------------------------
|
|
// Misc small procedures
|
|
// ----------------------------------------------------------------
|
|
|
|
|
|
// returns the current real time as a String
|
|
// see: https://randomnerdtutorials.com/esp32-date-time-ntp-client-server-arduino/
|
|
String localTime() {
|
|
struct tm timeinfo;
|
|
char ttime[40];
|
|
if(!getLocalTime(&timeinfo)) return"Failed to obtain time";
|
|
strftime(ttime,40, "%A, %B %d %Y %H:%M:%S", &timeinfo);
|
|
return ttime;
|
|
}
|
|
|
|
|
|
// flash the indicator led 'reps' number of times
|
|
void flashLED(int reps) {
|
|
for(int x=0; x < reps; x++) {
|
|
digitalWrite(indicatorLED,LOW);
|
|
delay(1000);
|
|
digitalWrite(indicatorLED,HIGH);
|
|
delay(500);
|
|
}
|
|
}
|
|
|
|
|
|
// send a standard html header (i.e. start of web page)
|
|
void sendHeader(WiFiClient &client) {
|
|
client.write("HTTP/1.1 200 OK\r\n");
|
|
client.write("Content-Type: text/html\r\n");
|
|
client.write("Connection: close\r\n");
|
|
client.write("\r\n");
|
|
client.write("<!DOCTYPE HTML>\n");
|
|
client.write("<html lang='en'>\n");
|
|
client.write("<head>\n");
|
|
client.write("<meta name='viewport' content='width=device-width, initial-scale=1.0'>\n");
|
|
}
|
|
|
|
|
|
// send a standard html footer (i.e. end of web page)
|
|
void sendFooter(WiFiClient &client) {
|
|
client.write("</body></html>\n");
|
|
delay(3);
|
|
client.stop();
|
|
}
|
|
|
|
|
|
// send line of text to both serial port and web page - used by readRGBImage
|
|
void sendText(WiFiClient &client, String theText) {
|
|
if (!sendRGBfile) client.print(theText + "<br>\n");
|
|
if (serialDebug || theText.indexOf("error") > 0) Serial.println(theText); // if text contains "error"
|
|
}
|
|
|
|
|
|
// ******************************************************************************************************************
|
|
|
|
|
|
// ----------------------------------------------------------------
|
|
// Capture image from camera and save to spiffs or sd card
|
|
// ----------------------------------------------------------------
|
|
// returns 0 if failed, 1 if stored in spiffs, 2 if stored on sd card
|
|
|
|
byte storeImage() {
|
|
|
|
byte sRes = 0; // result flag
|
|
fs::FS &fs = SD_MMC; // sd card file system
|
|
|
|
// capture the image from camera
|
|
int currentBrightness = brightLEDbrightness;
|
|
if (flashRequired) brightLed(255); // change LED brightness (0 - 255)
|
|
camera_fb_t *fb = esp_camera_fb_get(); // capture image frame from camera
|
|
if (flashRequired) brightLed(currentBrightness); // change LED brightness back to previous state
|
|
if (!fb) {
|
|
if (serialDebug) Serial.println("Error: Camera capture failed");
|
|
return 0;
|
|
}
|
|
|
|
// save image to Spiffs
|
|
if (!sdcardPresent) {
|
|
if (serialDebug) Serial.println("Storing image to spiffs only");
|
|
SPIFFS.remove(spiffsFilename); // delete old image file if it exists
|
|
File file = SPIFFS.open(spiffsFilename, FILE_WRITE);
|
|
if (!file) {
|
|
if (serialDebug) Serial.println("Failed to create file in Spiffs - will format and try again");
|
|
if (!SPIFFS.format()) {
|
|
if (serialDebug) Serial.println("Spiffs format failed");
|
|
} else {
|
|
file = SPIFFS.open(spiffsFilename, FILE_WRITE);
|
|
if (!file) {
|
|
if (serialDebug) Serial.println("Still unable to create file in spiffs");
|
|
}
|
|
}
|
|
}
|
|
if (file) { // if file has been created ok write data to it
|
|
if (file.write(fb->buf, fb->len)) {
|
|
sRes = 1; // flag as saved ok
|
|
} else {
|
|
if (serialDebug) Serial.println("Error: writing image to spiffs file");
|
|
}
|
|
}
|
|
if (sRes == 1 && serialDebug) {
|
|
Serial.print("The picture has been saved as " + spiffsFilename);
|
|
Serial.print(" - Size: ");
|
|
Serial.print(file.size());
|
|
Serial.println(" bytes");
|
|
}
|
|
file.close();
|
|
}
|
|
|
|
|
|
// save the image to sd card
|
|
if (sdcardPresent) {
|
|
if (serialDebug) Serial.printf("Storing image #%d to sd card \n", imageCounter);
|
|
String SDfilename = "/img/" + String(imageCounter + 1) + ".jpg"; // build the image file name
|
|
File file = fs.open(SDfilename, FILE_WRITE); // create file on sd card
|
|
if (!file) {
|
|
if (serialDebug) Serial.println("Error: Failed to create file on sd-card: " + SDfilename);
|
|
} else {
|
|
if (file.write(fb->buf, fb->len)) { // File created ok so save image to it
|
|
if (serialDebug) Serial.println("Image saved to sd card");
|
|
imageCounter ++; // increment image counter
|
|
sRes = 2; // flag as saved ok
|
|
} else {
|
|
if (serialDebug) Serial.println("Error: failed to save image to sd card");
|
|
}
|
|
file.close(); // close image file on sd card
|
|
}
|
|
}
|
|
|
|
esp_camera_fb_return(fb); // return frame so memory can be released
|
|
|
|
return sRes;
|
|
|
|
} // storeImage
|
|
|
|
|
|
|
|
// ******************************************************************************************************************
|
|
|
|
|
|
// ----------------------------------------------------------------
|
|
// -root web page requested i.e. http://x.x.x.x/
|
|
// ----------------------------------------------------------------
|
|
// web page with control buttons, links etc.
|
|
|
|
void handleRoot() {
|
|
|
|
getNTPtime(2); // refresh current time from NTP server
|
|
|
|
WiFiClient client = server.client(); // open link with client
|
|
|
|
|
|
// Action any button presses or settings entered on web page
|
|
|
|
// if button1 was pressed (toggle io pin A)
|
|
// Note: if using an input box etc. you would read the value with the command: String Bvalue = server.arg("demobutton1");
|
|
if (server.hasArg("button1")) {
|
|
if (serialDebug) Serial.println("Button 1 pressed");
|
|
digitalWrite(iopinA,!digitalRead(iopinA)); // toggle output pin on/off
|
|
}
|
|
|
|
// if button2 was pressed (toggle io pin B)
|
|
if (server.hasArg("button2")) {
|
|
if (serialDebug) Serial.println("Button 2 pressed");
|
|
digitalWrite(iopinB,!digitalRead(iopinB)); // toggle output pin on/off
|
|
}
|
|
|
|
// if button3 was pressed (toggle flash LED)
|
|
if (server.hasArg("button3")) {
|
|
if (serialDebug) Serial.println("Button 3 pressed");
|
|
if (brightLEDbrightness == 0) brightLed(10); // turn led on dim
|
|
else if (brightLEDbrightness == 10) brightLed(40); // turn led on medium
|
|
else if (brightLEDbrightness == 40) brightLed(255); // turn led on full
|
|
else brightLed(0); // turn led off
|
|
}
|
|
|
|
// if button4 was pressed (format SPIFFS)
|
|
if (server.hasArg("button4")) {
|
|
if (serialDebug) Serial.println("Button 4 pressed");
|
|
if (!SPIFFS.format()) {
|
|
if (serialDebug) Serial.println("Error: Unable to format Spiffs");
|
|
} else {
|
|
if (serialDebug) Serial.println("Spiffs memory has been formatted");
|
|
}
|
|
}
|
|
|
|
// if exposure was adjusted - cameraImageExposure
|
|
if (server.hasArg("exp")) {
|
|
if (serialDebug) Serial.println("Exposure has been changed");
|
|
String Tvalue = server.arg("exp"); // read value
|
|
if (Tvalue != NULL) {
|
|
int val = Tvalue.toInt();
|
|
if (val >= 0 && val <= 1200 && val != cameraImageExposure) {
|
|
if (serialDebug) Serial.printf("Exposure changed to %d\n", val);
|
|
cameraImageExposure = val;
|
|
cameraImageSettings(); // Apply camera image settings
|
|
}
|
|
}
|
|
}
|
|
|
|
// if image gain was adjusted - cameraImageGain
|
|
if (server.hasArg("gain")) {
|
|
if (serialDebug) Serial.println("Gain has been changed");
|
|
String Tvalue = server.arg("gain"); // read value
|
|
if (Tvalue != NULL) {
|
|
int val = Tvalue.toInt();
|
|
if (val >= 0 && val <= 31 && val != cameraImageGain) {
|
|
if (serialDebug) Serial.printf("Gain changed to %d\n", val);
|
|
cameraImageGain = val;
|
|
cameraImageSettings(); // Apply camera image settings
|
|
}
|
|
}
|
|
}
|
|
|
|
|
|
// html header
|
|
sendHeader(client);
|
|
client.write("<title>root</title> </head> <body>\n"); // basic html header
|
|
client.write("<FORM action='/' method='post'>\n"); // used by the buttons in the html (action = the web page to send it to
|
|
|
|
|
|
// --------------------------------------------------------------------
|
|
|
|
|
|
// html main body
|
|
// Info on the arduino ethernet library: https://www.arduino.cc/en/Reference/Ethernet
|
|
// Info in HTML: https://www.w3schools.com/html/
|
|
// Info on Javascript (can be inserted in to the HTML): https://www.w3schools.com/js/default.asp
|
|
// Verify your HTML is valid: https://validator.w3.org/
|
|
|
|
|
|
client.write("<h1>Hello from ESP32Cam</h1>\n");
|
|
|
|
// sd card details
|
|
if (sdcardPresent) client.printf("<p>SD Card detected - %d images stored</p>\n", imageCounter);
|
|
else client.write("<p>No SD Card detected</p>\n");
|
|
|
|
// io pin details
|
|
if (digitalRead(iopinA) == LOW) client.write("<p>Output Pin 13 is Low</p>\n");
|
|
else client.write("<p>Output Pin 13 is High</p>\n");
|
|
|
|
if (digitalRead(iopinB) == LOW) client.write("<p>Output Pin 12 is Low</p>\n");
|
|
else client.write("<p>Output Pin 12 is High</p>\n");
|
|
|
|
if (digitalRead(iopinC) == LOW) client.write("<p>Input Pin 16 is Low</p>\n");
|
|
else client.write("<p>Input Pin 16 is High</p>\n");
|
|
|
|
// illumination led brightness
|
|
client.printf("<p>Illumination led set to %d</p>\n", brightLEDbrightness);
|
|
|
|
// Current real time
|
|
client.print("<p>Current time: " + localTime() + "</p>\n");
|
|
|
|
// // touch input on the two gpio pins
|
|
// client.printf("<p>Touch on pin 12: %d </p>\n", touchRead(T5) );
|
|
// client.printf("<p>Touch on pin 13: %d </p>\n", touchRead(T4) );
|
|
|
|
// Control bottons
|
|
client.write("<input style='height: 35px;' name='button1' value='Toggle pin 13' type='submit'> \n");
|
|
client.write("<input style='height: 35px;' name='button2' value='Toggle pin 12' type='submit'> \n");
|
|
client.write("<input style='height: 35px;' name='button3' value='Toggle Flash' type='submit'> \n");
|
|
client.write("<input style='height: 35px;' name='button4' value='Wipe SPIFFS memory' type='submit'><br> \n");
|
|
|
|
// Image setting controls
|
|
client.write("<br>CAMERA SETTINGS: \n");
|
|
client.printf("Exposure: <input type='number' style='width: 50px' name='exp' min='0' max='1200' value='%d'> \n", cameraImageExposure);
|
|
client.printf("Gain: <input type='number' style='width: 50px' name='gain' min='0' max='30' value='%d'>\n", cameraImageGain);
|
|
client.write(" - Set both to zero for auto adjust<br>\n");
|
|
|
|
// links to the other pages available
|
|
client.write("<br>LINKS: \n");
|
|
client.write("<a href='/photo'>Capture an image</a> - \n");
|
|
client.write("<a href='/img'>View stored image</a> - \n");
|
|
client.write("<a href='/rgb'>Capture Image as raw RGB data</a> - \n");
|
|
client.write("<a href='/stream'>Live stream</a><br>\n");
|
|
|
|
// capture and show a jpg image
|
|
client.write("<br><a href='/jpg'>"); // make it a link
|
|
client.write("<img src='/jpg' /> </a>"); // show image from http://x.x.x.x/jpg
|
|
|
|
|
|
// --------------------------------------------------------------------
|
|
|
|
|
|
sendFooter(client); // close web page
|
|
|
|
} // handleRoot
|
|
|
|
|
|
// ******************************************************************************************************************
|
|
|
|
|
|
// ----------------------------------------------------------------
|
|
// -photo save to sd card/spiffs i.e. http://x.x.x.x/photo
|
|
// ----------------------------------------------------------------
|
|
// web page to capture an image from camera and save to spiffs or sd card
|
|
|
|
void handlePhoto() {
|
|
|
|
WiFiClient client = server.client(); // open link with client
|
|
|
|
// log page request including clients IP
|
|
IPAddress cIP = client.remoteIP();
|
|
if (serialDebug) Serial.println("Save photo requested by " + cIP.toString());
|
|
|
|
|
|
// save an image to sd card or spiffs
|
|
byte sRes = storeImage(); // save an image to sd card or spiffs (store sucess or failed flag - 0=fail, 1=spiffs only, 2=spiffs and sd card)
|
|
|
|
// html header
|
|
sendHeader(client);
|
|
client.write("<title>photo</title> </head> <body>\n"); // basic html header
|
|
|
|
// html body
|
|
if (sRes == 2) {
|
|
client.printf("<p>Image saved to sd card as image number %d </p>\n", imageCounter);
|
|
} else if (sRes == 1) {
|
|
client.write("<p>Image saved in Spiffs</p>\n");
|
|
} else {
|
|
client.write("<p>Error: Failed to save image to sd card</p>\n");
|
|
}
|
|
client.write("<a href='/'>Return</a>\n"); // link back
|
|
sendFooter(client); // close web page
|
|
|
|
} // handlePhoto
|
|
|
|
|
|
|
|
// ----------------------------------------------------------------
|
|
// -display image stored on sd card or SPIFFS i.e. http://x.x.x.x/img?img=x
|
|
// ----------------------------------------------------------------
|
|
// Display a previously stored image, default image = most recent
|
|
// returns 1 if image displayed ok
|
|
|
|
bool handleImg() {
|
|
|
|
WiFiClient client = server.client(); // open link with client
|
|
bool pRes = 0;
|
|
|
|
// log page request including clients IP
|
|
IPAddress cIP = client.remoteIP();
|
|
if (serialDebug) Serial.println("Display stored image requested by " + cIP.toString());
|
|
|
|
int imgToShow = imageCounter; // default to showing most recent file
|
|
|
|
// get image number from url parameter
|
|
if (server.hasArg("img")) {
|
|
String Tvalue = server.arg("img"); // read value
|
|
imgToShow = Tvalue.toInt(); // convert string to int
|
|
if (imgToShow < 1 || imgToShow > imageCounter) imgToShow = imageCounter; // validate image number
|
|
}
|
|
|
|
// if stored on sd card
|
|
if (sdcardPresent) {
|
|
if (serialDebug) Serial.printf("Displaying image #%d from sd card", imgToShow);
|
|
|
|
String tFileName = "/img/" + String(imgToShow) + ".jpg";
|
|
fs::FS &fs = SD_MMC; // sd card file system
|
|
File timg = fs.open(tFileName, "r");
|
|
if (timg) {
|
|
size_t sent = server.streamFile(timg, "image/jpeg"); // send the image
|
|
timg.close();
|
|
pRes = 1; // flag sucess
|
|
} else {
|
|
if (serialDebug) Serial.println("Error: image file not found");
|
|
WiFiClient client = server.client(); // open link with client
|
|
client.write("<!DOCTYPE html> <html> <body>\n");
|
|
client.write("<p>Error: Image not found</p></html>\n");
|
|
delay(3);
|
|
client.stop();
|
|
}
|
|
}
|
|
|
|
// if stored in SPIFFS
|
|
if (!sdcardPresent) {
|
|
if (serialDebug) Serial.println("Displaying image from spiffs");
|
|
File f = SPIFFS.open(spiffsFilename, "r"); // read file from spiffs
|
|
if (!f) {
|
|
if (serialDebug) Serial.println("Error reading " + spiffsFilename);
|
|
}
|
|
else {
|
|
size_t sent = server.streamFile(f, "image/jpeg"); // send file to web page
|
|
if (!sent) {
|
|
if (serialDebug) Serial.println("Error sending " + spiffsFilename);
|
|
} else {
|
|
pRes = 1; // flag sucess
|
|
}
|
|
f.close();
|
|
}
|
|
}
|
|
return pRes;
|
|
|
|
} // handleImg
|
|
|
|
|
|
// ******************************************************************************************************************
|
|
|
|
|
|
// ----------------------------------------------------------------
|
|
// -invalid web page requested
|
|
// ----------------------------------------------------------------
|
|
// Note: shows a different way to send the HTML reply
|
|
|
|
void handleNotFound() {
|
|
|
|
String tReply;
|
|
|
|
if (serialDebug) Serial.print("Invalid page requested");
|
|
|
|
tReply = "File Not Found\n\n";
|
|
tReply += "URI: ";
|
|
tReply += server.uri();
|
|
tReply += "\nMethod: ";
|
|
tReply += ( server.method() == HTTP_GET ) ? "GET" : "POST";
|
|
tReply += "\nArguments: ";
|
|
tReply += server.args();
|
|
tReply += "\n";
|
|
|
|
for ( uint8_t i = 0; i < server.args(); i++ ) {
|
|
tReply += " " + server.argName ( i ) + ": " + server.arg ( i ) + "\n";
|
|
}
|
|
|
|
server.send ( 404, "text/plain", tReply );
|
|
tReply = ""; // clear variable
|
|
|
|
} // handleNotFound
|
|
|
|
|
|
// ******************************************************************************************************************
|
|
|
|
|
|
// ----------------------------------------------------------------
|
|
// -access image data as RGB - i.e. http://x.x.x.x/rgb
|
|
// ----------------------------------------------------------------
|
|
//Demonstration on how to access raw RGB data from the camera
|
|
// Notes:
|
|
// Set sendRGBfile to 1 in the settings at top of sketch to just send the raw rgb data as a file which can then be used with
|
|
// the Processing sketch: https://github.com/alanesq/esp32cam-demo/blob/master/Misc/displayRGB.pde
|
|
// otherwise a web page is displayed showing some sample rgb data usage.
|
|
// You may want to disable auto white balance when experimenting with RGB otherwise the camera is always trying to adjust the
|
|
// image colours to mainly white. (disable in the 'cameraImageSettings' procedure).
|
|
// It will fail on the higher resolutions as it requires more than the 4mb of available psram to store the data (1600x1200x3 bytes)
|
|
// I learned how to read the RGB data from: https://github.com/Makerfabs/Project_Touch-Screen-Camera/blob/master/Camera_v2/Camera_v2.ino
|
|
|
|
void readRGBImage() {
|
|
// used for timing operations
|
|
WiFiClient client = server.client();
|
|
uint32_t tTimer; // used to time tasks // open link with client
|
|
|
|
if (!sendRGBfile) {
|
|
// html header
|
|
sendHeader(client);
|
|
client.write("<title>Show RGB data</title> </head> <body>\n"); // basic html header
|
|
|
|
// page title including clients IP
|
|
IPAddress cIP = client.remoteIP();
|
|
sendText(client, "Live image as rgb data, requested by " + cIP.toString()); // 'sendText' sends the String to both serial port and web page
|
|
}
|
|
|
|
// make sure psram is available
|
|
if (!psramFound()) {
|
|
sendText(client,"error: no psram available to store the RGB data");
|
|
if (!sendRGBfile) sendFooter(client); // close web page
|
|
return;
|
|
}
|
|
|
|
|
|
// ****** the main code for converting an image to RGB data *****
|
|
|
|
// capture a live image from camera (as a jpg)
|
|
camera_fb_t * fb = NULL;
|
|
tTimer = millis(); // store time that image capture started
|
|
fb = esp_camera_fb_get();
|
|
if (!fb) {
|
|
sendText(client,"error: failed to capture image from camera");
|
|
if (!sendRGBfile) sendFooter(client); // close web page
|
|
return;
|
|
} else {
|
|
sendText(client, "-JPG image capture took " + String(millis() - tTimer) + " milliseconds"); // report time it took to capture an image
|
|
sendText(client,"-Image resolution=" + String(fb->width) + "x" + String(fb->height));
|
|
sendText(client,"-Image size=" + String(fb->len) + " bytes");
|
|
}
|
|
|
|
// display captured image using base64
|
|
if (!sendRGBfile) {
|
|
client.println("<br><img src='data:image/png;base64," + base64::encode(fb->buf, fb->len) + "'><br>");
|
|
}
|
|
|
|
// allocate memory to store the rgb data (in psram, 3 bytes per pixel)
|
|
sendText(client,"<br>Free psram before rgb data allocated = " + String(heap_caps_get_free_size(MALLOC_CAP_SPIRAM) / 1024) + "K");
|
|
void *ptrVal = NULL; // create a pointer for memory location to store the data
|
|
uint32_t ARRAY_LENGTH = fb->width * fb->height * 3; // calculate memory required to store the RGB data (i.e. number of pixels in the jpg image x 3)
|
|
if (heap_caps_get_free_size( MALLOC_CAP_SPIRAM) < ARRAY_LENGTH) {
|
|
sendText(client,"error: not enough free psram to store the rgb data");
|
|
if (!sendRGBfile) sendFooter(client); // close web page
|
|
return;
|
|
}
|
|
ptrVal = heap_caps_malloc(ARRAY_LENGTH, MALLOC_CAP_SPIRAM); // allocate memory space for the rgb data
|
|
uint8_t *rgb = (uint8_t *)ptrVal; // create the 'rgb' array pointer to the allocated memory space
|
|
sendText(client,"Free psram after rgb data allocated = " + String(heap_caps_get_free_size(MALLOC_CAP_SPIRAM) / 1024) + "K");
|
|
|
|
// convert the captured jpg image (fb) to rgb data (store in 'rgb' array)
|
|
tTimer = millis(); // store time that image conversion process started
|
|
bool jpeg_converted = fmt2rgb888(fb->buf, fb->len, PIXFORMAT_JPEG, rgb);
|
|
if (!jpeg_converted) {
|
|
sendText(client,"error: failed to convert image to RGB data");
|
|
if (!sendRGBfile) sendFooter(client); // close web page
|
|
return;
|
|
}
|
|
sendText(client, "Conversion from jpg to RGB took " + String(millis() - tTimer) + " milliseconds");// report how long the conversion took
|
|
|
|
|
|
// if sendRGBfile is set then just send raw RGB data and close
|
|
if (sendRGBfile) {
|
|
client.write(rgb, ARRAY_LENGTH); // send the raw rgb data
|
|
esp_camera_fb_return(fb); // camera frame buffer
|
|
delay(3);
|
|
client.stop();
|
|
return;
|
|
}
|
|
|
|
|
|
// ****** examples of using the resulting RGB data *****
|
|
|
|
// display some of the resulting data
|
|
uint32_t resultsToShow = 50; // how much data to display
|
|
sendText(client,"<br>R , G , B - for first " + String(resultsToShow) + " pixels of image");
|
|
for (uint32_t i = 0; i < resultsToShow-2; i+=3) {
|
|
sendText(client,String(rgb[i+2]) + "," + String(rgb[i+1]) + "," + String(rgb[i+0])); // Red , Green , Blue
|
|
// // calculate the x and y coordinate of the current pixel
|
|
// uint16_t x = (i / 3) % fb->width;
|
|
// uint16_t y = floor( (i / 3) / fb->width);
|
|
}
|
|
|
|
// find the average values for each colour over entire image
|
|
uint32_t aRed = 0;
|
|
uint32_t aGreen = 0;
|
|
uint32_t aBlue = 0;
|
|
for (uint32_t i = 0; i < (ARRAY_LENGTH - 2); i+=3) { // go through all data and add up totals
|
|
aBlue+=rgb[i];
|
|
aGreen+=rgb[i+1];
|
|
aRed+=rgb[i+2];
|
|
}
|
|
aRed = aRed / (fb->width * fb->height); // divide total by number of pixels to give the average value
|
|
aGreen = aGreen / (fb->width * fb->height);
|
|
aBlue = aBlue / (fb->width * fb->height);
|
|
sendText(client,"Average Blue = " + String(aBlue));
|
|
sendText(client,"Average Green = " + String(aGreen));
|
|
sendText(client,"Average Red = " + String(aRed));
|
|
|
|
|
|
// *******************************************************
|
|
|
|
client.write("<br><a href='/'>Return</a>\n"); // link back
|
|
sendFooter(client); // close web page
|
|
|
|
// finished with the data so free up the memory space used in psram
|
|
esp_camera_fb_return(fb); // camera frame buffer
|
|
heap_caps_free(ptrVal); // rgb data
|
|
|
|
} // readRGBImage
|
|
|
|
|
|
|
|
// ******************************************************************************************************************
|
|
|
|
|
|
// ----------------------------------------------------------------
|
|
// -get time from ntp server
|
|
// ----------------------------------------------------------------
|
|
|
|
bool getNTPtime(int sec) {
|
|
|
|
uint32_t start = millis(); // timeout timer
|
|
|
|
do {
|
|
time(&now);
|
|
localtime_r(&now, &timeinfo);
|
|
if (serialDebug) Serial.print(".");
|
|
delay(100);
|
|
} while (((millis() - start) <= (1000 * sec)) && (timeinfo.tm_year < (2016 - 1900)));
|
|
|
|
if (timeinfo.tm_year <= (2016 - 1900)) return false; // the NTP call was not successful
|
|
if (serialDebug) {
|
|
Serial.print("now ");
|
|
Serial.println(now);
|
|
}
|
|
|
|
// Display time
|
|
if (serialDebug) {
|
|
char time_output[30];
|
|
strftime(time_output, 30, "%a %d-%m-%y %T", localtime(&now));
|
|
Serial.println(time_output);
|
|
Serial.println();
|
|
}
|
|
return true;
|
|
}
|
|
|
|
|
|
// ----------------------------------------------------------------
|
|
// -capture jpg image and send i.e. http://x.x.x.x/jpg
|
|
// ----------------------------------------------------------------
|
|
|
|
bool handleJPG() {
|
|
|
|
WiFiClient client = server.client(); // open link with client
|
|
char buf[32];
|
|
camera_fb_t * fb = NULL; // pointer for image frame buffer
|
|
|
|
// capture the jpg image from camera
|
|
fb = esp_camera_fb_get();
|
|
if (!fb) {
|
|
if (serialDebug) Serial.println("Error: failed to capture image");
|
|
return 0;
|
|
}
|
|
|
|
// html to send a jpg
|
|
const char HEADER[] = "HTTP/1.1 200 OK\r\nAccess-Control-Allow-Origin: *\r\n";
|
|
const char CTNTTYPE[] = "Content-Type: image/jpeg\r\nContent-Length: ";
|
|
const int hdrLen = strlen(HEADER);
|
|
const int cntLen = strlen(CTNTTYPE);
|
|
client.write(HEADER, hdrLen);
|
|
client.write(CTNTTYPE, cntLen);
|
|
sprintf( buf, "%d\r\n\r\n", fb->len); // put text size in to 'buf' char array and send
|
|
client.write(buf, strlen(buf));
|
|
|
|
// send the captured jpg data
|
|
client.write((char *)fb->buf, fb->len);
|
|
|
|
// close client connection
|
|
delay(3);
|
|
client.stop();
|
|
|
|
// return image frame so memory can be released
|
|
esp_camera_fb_return(fb);
|
|
|
|
return 1;
|
|
|
|
} // handleJPG
|
|
|
|
|
|
|
|
// ----------------------------------------------------------------
|
|
// -stream requested i.e. http://x.x.x.x/stream
|
|
// ----------------------------------------------------------------
|
|
// Sends video stream - thanks to Uwe Gerlach for the code showing me how to do this
|
|
|
|
void handleStream(){
|
|
|
|
WiFiClient client = server.client(); // open link with client
|
|
char buf[32];
|
|
camera_fb_t * fb = NULL;
|
|
|
|
// log page request including clients IP
|
|
IPAddress cIP = client.remoteIP();
|
|
if (serialDebug) Serial.println("Live stream requested by " + cIP.toString());
|
|
|
|
// html
|
|
const char HEADER[] = "HTTP/1.1 200 OK\r\n" \
|
|
"Access-Control-Allow-Origin: *\r\n" \
|
|
"Content-Type: multipart/x-mixed-replace; boundary=123456789000000000000987654321\r\n";
|
|
const char BOUNDARY[] = "\r\n--123456789000000000000987654321\r\n"; // marks end of each image frame
|
|
const char CTNTTYPE[] = "Content-Type: image/jpeg\r\nContent-Length: "; // marks start of image data
|
|
const int hdrLen = strlen(HEADER); // length of the stored text, used when sending to web page
|
|
const int bdrLen = strlen(BOUNDARY);
|
|
const int cntLen = strlen(CTNTTYPE);
|
|
client.write(HEADER, hdrLen);
|
|
client.write(BOUNDARY, bdrLen);
|
|
|
|
// send live jpg images until client disconnects
|
|
while (true)
|
|
{
|
|
if (!client.connected()) break;
|
|
fb = esp_camera_fb_get(); // capture live image as jpg
|
|
if (!fb) {
|
|
if (serialDebug) Serial.println("Error: failed to capture jpg image");
|
|
} else {
|
|
// send image
|
|
client.write(CTNTTYPE, cntLen); // send content type html (i.e. jpg image)
|
|
sprintf( buf, "%d\r\n\r\n", fb->len); // format the image's size as html and put in to 'buf'
|
|
client.write(buf, strlen(buf)); // send result (image size)
|
|
client.write((char *)fb->buf, fb->len); // send the image data
|
|
client.write(BOUNDARY, bdrLen); // send html boundary see https://developer.mozilla.org/en-US/docs/Web/HTTP/Headers/Content-Type
|
|
esp_camera_fb_return(fb); // return image buffer so memory can be released
|
|
}
|
|
}
|
|
|
|
if (serialDebug) Serial.println("Video stream stopped");
|
|
delay(3);
|
|
client.stop();
|
|
|
|
|
|
} // handleStream
|
|
|
|
|
|
// ******************************************************************************************************************
|
|
|
|
|
|
// ----------------------------------------------------------------
|
|
// request a web page
|
|
// ----------------------------------------------------------------
|
|
// @param page web page to request
|
|
// @param received String to store response in
|
|
// @param maxWaitTime maximum time to wait for reply (ms)
|
|
// @returns http code
|
|
// see: https://randomnerdtutorials.com/esp32-http-get-post-arduino/#http-get-1
|
|
// to do: limit size of reply
|
|
|
|
int requestWebPage(String* page, String* received, int maxWaitTime=5000){
|
|
|
|
if (serialDebug) Serial.println("requesting web page: " + *page);
|
|
|
|
WiFiClient client;
|
|
HTTPClient http; // see: https://github.com/esp8266/Arduino/blob/master/libraries/ESP8266HTTPClient
|
|
http.setTimeout(maxWaitTime);
|
|
http.begin(client, *page); // for https requires (client, *page, thumbprint) e.g.String thumbprint="08:3B:71:72:02:43:6E:CA:ED:42:86:93:BA:7E:DF:81:C4:BC:62:30";
|
|
int httpCode = http.GET(); // http codes: https://en.wikipedia.org/wiki/List_of_HTTP_status_codes
|
|
if (serialDebug) Serial.println("http code: " + String(httpCode));
|
|
|
|
if (httpCode > 0) {
|
|
*received = http.getString();
|
|
} else {
|
|
*received = "error:" + String(httpCode);
|
|
}
|
|
if (serialDebug) Serial.println(*received);
|
|
|
|
http.end(); //Close connection
|
|
if (serialDebug) Serial.println("Web connection closed");
|
|
|
|
return httpCode;
|
|
|
|
} // requestWebPage
|
|
|
|
|
|
// ******************************************************************************************************************
|
|
|
|
|
|
// ----------------------------------------------------------------
|
|
// -test procedure i.e. http://x.x.x.x/test
|
|
// ----------------------------------------------------------------
|
|
|
|
void handleTest() {
|
|
|
|
WiFiClient client = server.client(); // open link with client
|
|
|
|
// log page request including clients IP
|
|
IPAddress cIP = client.remoteIP();
|
|
if (serialDebug) Serial.println("Test page requested by " + cIP.toString());
|
|
|
|
// html header
|
|
sendHeader(client);
|
|
client.write("<title>photo</title> </head> <body>\n"); // basic html header
|
|
|
|
|
|
// html body
|
|
client.print("<h1>Test Page</h1>\n");
|
|
|
|
|
|
// -------------------------------------------------------------------
|
|
|
|
|
|
|
|
|
|
// test code goes here
|
|
|
|
|
|
|
|
|
|
/*
|
|
// demo of how to request a web page
|
|
String page = "http://urlhere.com"; // url to request
|
|
String response; // reply will be stored here
|
|
int httpCode = requestWebPage(&page, &response);
|
|
// show results
|
|
client.println("Web page requested: '" + page + "' - http code: " + String(httpCode));
|
|
client.print("<xmp>'"); // enables the html code to be displayed
|
|
client.print(response);
|
|
client.println("'</xmp><br>");
|
|
*/
|
|
|
|
|
|
/*
|
|
// // demo useage of the mcp23017 io chip
|
|
#if useMCP23017 == 1
|
|
while(1) {
|
|
mcp.digitalWrite(0, HIGH);
|
|
int q = mcp.digitalRead(8);
|
|
client.print("<p>HIGH, input =" + String(q) + "</p>");
|
|
delay(1000);
|
|
mcp.digitalWrite(0, LOW);
|
|
client.print("<p>LOW</p>");
|
|
delay(1000);
|
|
}
|
|
#endif
|
|
*/
|
|
|
|
|
|
// -------------------------------------------------------------------
|
|
|
|
|
|
sendFooter(client); // close web page
|
|
|
|
} // handleTest
|
|
|
|
|
|
// ******************************************************************************************************************
|
|
// end
|