kopia lustrzana https://github.com/pjalocha/esp32-ogn-tracker
80 wiersze
4.1 KiB
INI
80 wiersze
4.1 KiB
INI
#define DEFAULT_AcftType 1 // [0..15] default aircraft-type: glider
|
|
#define DEFAULT_GeoidSepar 40 // [m]
|
|
#define DEFAULT_CONbaud 115200
|
|
#define DEFAULT_PPSdelay 100
|
|
#define DEFAULT_FreqPlan 0
|
|
|
|
|
|
// #define WITH_HELTEC // HELTEC module: PCB LED on GPI025
|
|
#define WITH_HELTEC_V2 // HELTEC module v2
|
|
// #define WITH_TTGO // TTGO module: PCB LED on GPIO2, GPIO25 free to use as DAC2 output
|
|
// #define WITH_TBEAM // T-Beam module
|
|
// #define WITH_TBEAM_V10 // T-Beam module
|
|
// #define WITH_M5_JACEK // JACEK M5 ESP32 OGN-Tracker
|
|
// #define WITH_FollowMe // by Avionix
|
|
|
|
// #define WITH_ILI9341 // 320x240 M5stack
|
|
// #define WITH_ST7789 // IPS 240x240 ST7789
|
|
// #define WITH_TFT_LCD // TFT LCD
|
|
// #define WITH_OLED // OLED display on the I2C: some TTGO modules are without OLED display
|
|
// #define WITH_OLED2 // 2nd OLED display, I2C address next higher
|
|
#define WITH_U8G2_OLED // I2C OLED through the U8g2 library
|
|
// #define WITH_U8G2_SH1106 // correct controller for the bigger OLED
|
|
// #define WITH_U8G2_FLIP // flip the OLED screen (rotate by 180deg)
|
|
|
|
#define WITH_RFM95 // RF chip selection: both HELTEC and TTGO use sx1276 which is same as RFM95
|
|
|
|
// #define WITH_SLEEP // with software sleep mode controlled by the long-press on the button
|
|
|
|
// #define WITH_AXP // with AXP192 power controller (T-BEAM V1.0)
|
|
// #define WITH_BQ // with BQ24295 power controller (FollowMe)
|
|
|
|
// #define WITH_LED_RX
|
|
// #define WITH_LED_TX
|
|
|
|
// #define WITH_GPS_ENABLE // use GPS_ENABLE control line to turn the GPS ON/OFF
|
|
// #define WITH_GPS_PPS // use the PPS signal from GPS for precise time-sync.
|
|
// #define WITH_GPS_CONFIG // attempt to configure higher GPS baud rate and airborne mode
|
|
|
|
// #define WITH_GPS_UBX // GPS understands UBX
|
|
// #define WITH_GPS_MTK // GPS understands MTK
|
|
// #define WITH_GPS_SRF
|
|
#define WITH_MAVLINK
|
|
|
|
// #define WITH_GPS_UBX_PASS // to pass directly UBX packets to/from GPS
|
|
// #define WITH_GPS_NMEA_PASS // to pass directly NMEA to/from GPS
|
|
|
|
// #define WITH_BMP180 // BMP180 pressure sensor
|
|
// #define WITH_BMP280 // BMP280 pressure sensor
|
|
// #define WITH_BME280 // BMP280 with humidity (but still works with BMP280)
|
|
// #define WITH_MS5607 // MS5607 pressure sensor
|
|
// #define WITH_MS5611 // MS5611 pressure sensor
|
|
|
|
// #define WITH_BMX055 // BMX055 magnetic and IMU sensor
|
|
|
|
// #define WITH_FANET
|
|
#define WITH_PFLAA // PFLAU and PFLAA for compatibility with XCsoar and LK8000
|
|
// #define WITH_POGNT
|
|
// #define WITH_GDL90
|
|
// #define WITH_PGAV5
|
|
#define WITH_LOOKOUT
|
|
|
|
#define WITH_CONFIG // interpret the console input: $POGNS to change parameters
|
|
|
|
// #define WITH_BEEPER // with digital buzzer
|
|
// #define WITH_SOUND // with analog sound produced by DAC on pin 25
|
|
|
|
// #define WITH_KNOB
|
|
// #define WITH_VARIO
|
|
|
|
// #define WITH_SD // use the SD card in SPI mode and FAT file system
|
|
// #define WITH_SDLOG // log own position and other data to uSD card
|
|
#define WITH_SPIFFS // use SPIFFS file system in Flash
|
|
#define WITH_LOG // log own positions and other received to SPIFFS
|
|
|
|
#define WITH_BT_SPP // Bluetooth serial port for smartphone/tablet link
|
|
// #define WITH_WIFI // attempt to connect to the wifi router for uploading the log files
|
|
|
|
// #define WITH_ENCRYPT // Encrypt (optionally) the position
|
|
|