kopia lustrzana https://github.com/pjalocha/esp32-ogn-tracker
46 wiersze
1.9 KiB
C
46 wiersze
1.9 KiB
C
#ifndef __SSD1306_H__
|
|
#define __SSD1306_H__
|
|
|
|
// http://robotcantalk.blogspot.com/2015/03/interfacing-arduino-with-ssd1306-driven.html
|
|
|
|
// SLA (0x3C) + WRITE_MODE (0x00) = 0x78
|
|
#define OLED_I2C_ADDRESS 0x3C
|
|
|
|
// Control byte
|
|
#define OLED_CONTROL_BYTE_CMD_SINGLE 0x80
|
|
#define OLED_CONTROL_BYTE_CMD_STREAM 0x00
|
|
#define OLED_CONTROL_BYTE_DATA_STREAM 0x40
|
|
|
|
// Fundamental commands (pg.28)
|
|
#define OLED_CMD_SET_CONTRAST 0x81 // follow with 0x7F
|
|
#define OLED_CMD_DISPLAY_RAM 0xA4
|
|
#define OLED_CMD_DISPLAY_ALLON 0xA5
|
|
#define OLED_CMD_DISPLAY_NORMAL 0xA6
|
|
#define OLED_CMD_DISPLAY_INVERTED 0xA7
|
|
#define OLED_CMD_DISPLAY_OFF 0xAE
|
|
#define OLED_CMD_DISPLAY_ON 0xAF
|
|
|
|
// Addressing Command Table (pg.30)
|
|
#define OLED_CMD_SET_MEMORY_ADDR_MODE 0x20 // follow with 0x00 = HORZ mode = Behave like a KS108 graphic LCD
|
|
#define OLED_CMD_SET_COLUMN_RANGE 0x21 // can be used only in HORZ/VERT mode - follow with 0x00 and 0x7F = COL127
|
|
#define OLED_CMD_SET_PAGE_RANGE 0x22 // can be used only in HORZ/VERT mode - follow with 0x00 and 0x07 = PAGE7
|
|
|
|
// Hardware Config (pg.31)
|
|
#define OLED_CMD_SET_DISPLAY_START_LINE 0x40
|
|
#define OLED_CMD_SET_SEGMENT_REMAP 0xA1
|
|
#define OLED_CMD_SET_MUX_RATIO 0xA8 // follow with 0x3F = 64 MUX
|
|
#define OLED_CMD_SET_COM_SCAN_MODE 0xC8
|
|
#define OLED_CMD_SET_DISPLAY_OFFSET 0xD3 // follow with 0x00
|
|
#define OLED_CMD_SET_COM_PIN_MAP 0xDA // follow with 0x12
|
|
#define OLED_CMD_NOP 0xE3 // NOP
|
|
|
|
// Timing and Driving Scheme (pg.32)
|
|
#define OLED_CMD_SET_DISPLAY_CLK_DIV 0xD5 // follow with 0x80
|
|
#define OLED_CMD_SET_PRECHARGE 0xD9 // follow with 0xF1
|
|
#define OLED_CMD_SET_VCOMH_DESELCT 0xDB // follow with 0x30
|
|
|
|
// Charge Pump (pg.62)
|
|
#define OLED_CMD_SET_CHARGE_PUMP 0x8D // follow with 0x14
|
|
|
|
#endif // __SSD1306_H__
|