mirror
/
esp32-ogn-tracker
kopia lustrzana https://github.com/pjalocha/esp32-ogn-tracker
1
0
Forkuj 0
Kod Zgłoszenia Projekty Wydania Wiki Aktywność

Add WITH_LORA32 pin configuration for LoRa32 board by TTGO, untested

pull/36/head
Pawel Jalocha 2021-02-08 19:22:38 +00:00
rodzic 0ea2e24488
commit dc4609678d
1 zmienionych plików z 18 dodań i 9 usunięć
Pokaż statystyki Ściągnij plik aktualizacji Ściągnij plik porównania Expand all files Collapse all files

27
main/hal.cpp
Wyświetl plik

@ -267,7 +267,7 @@ GPIO HELTEC TTGO JACEK M5_JACEK T-Beam T-Beamv10 Foll
#define PIN_RFM_MOSI GPIO_NUM_27 // SPI MOSI
#endif // HELTEC TTGO
#ifdef WITH_TBEAM
#if defined(WITH_TBEAM) || defined(WITH_TBEAM_V10) || defined(WITH_LORA32)
#define PIN_RFM_RST GPIO_NUM_23 // Reset - not clear if T-Beam is using it, or maybe only the older version
#define PIN_RFM_IRQ GPIO_NUM_26 // packet done on receive or transmit
#define PIN_RFM_SS GPIO_NUM_18 // SPI chip-select
@ -277,16 +277,10 @@ GPIO HELTEC TTGO JACEK M5_JACEK T-Beam T-Beamv10 Foll
#endif // TBEAM
#ifdef WITH_TBEAM_V10
#define PIN_RFM_RST GPIO_NUM_23 // Reset 23
#define PIN_RFM_IRQ GPIO_NUM_26 // packet done on receive or transmit
#ifdef WITH_SX1262
#define PIN_RFM_BUSY GPIO_NUM_32 // for the T-Beam with SX1262
#endif
#define PIN_RFM_SS GPIO_NUM_18 // SPI chip-select
#define PIN_RFM_SCK GPIO_NUM_5 // SPI clock
#define PIN_RFM_MISO GPIO_NUM_19 // SPI MISO
#define PIN_RFM_MOSI GPIO_NUM_27 // SPI MOSI
#endif // TBEAM
#endif
#ifdef WITH_FollowMe
// #define PIN_RFM_RST GPIO_NUM_32 // Reset
@ -334,6 +328,13 @@ GPIO HELTEC TTGO JACEK M5_JACEK T-Beam T-Beamv10 Foll
#define PIN_GPS_PPS GPIO_NUM_26
#endif // M5_JACEK
#ifdef WITH_LORA32
#define PIN_GPS_TXD GPIO_NUM_12
#define PIN_GPS_RXD GPIO_NUM_35
#define PIN_GPS_PPS GPIO_NUM_34
#define PIN_GPS_ENA GPIO_NUM_13
#endif // LORA32
#ifdef WITH_TBEAM_V10
#define PIN_AXP_IRQ GPIO_NUM_35
#endif
@ -407,7 +408,7 @@ uint8_t BARO_I2C = (uint8_t)I2C_BUS;
#define PIN_OLED_RST GPIO_NUM_16 // OLED RESET: low-active
#endif // HELTEC || TTGO
#if defined(WITH_TBEAM) || defined(WITH_TBEAM_V10) // T-Beam
#if defined(WITH_TBEAM) || defined(WITH_TBEAM_V10) || defined(WITH_LORA32) // T-Beam
#define PIN_I2C_SCL GPIO_NUM_22 // SCL pin => this way the pin pattern fits the BMP280 module
#define PIN_I2C_SDA GPIO_NUM_21 // SDA pin
#define OLED_I2C_ADDR 0x3C // I2C address of the OLED display
@ -424,6 +425,14 @@ uint8_t BARO_I2C = (uint8_t)I2C_BUS;
// #define PIN_OLED_RST GPIO_NUM_16 // OLED RESET: low-active
// #endif
#ifdef WITH_LORA32
#define PIN_SD_CS GPIO_NUM_13 // SD card interface in SPI mode
#define PIN_SD_SCK GPIO_NUM_14
#define PIN_SD_MISO GPIO_NUM_2
#define PIN_SD_MOSI GPIO_NUM_15
#define SD_SPI_DMA 2
#endif
#ifdef WITH_JACEK
#define PIN_OLED_RST GPIO_NUM_33 // OLED RESET: low-active