From b30f589def4f08e5cafe440df14f5ce313a161a5 Mon Sep 17 00:00:00 2001 From: Pawel Jalocha Date: Thu, 7 May 2020 22:39:01 +0100 Subject: [PATCH] Config. files for T-Beam with OLED --- T-Beam_OLED.cfg | 74 ++++++++++++++++++++++++++++++++++++++++++++ T-Beam_new_OLED.cfg | 75 +++++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 149 insertions(+) create mode 100644 T-Beam_OLED.cfg create mode 100644 T-Beam_new_OLED.cfg diff --git a/T-Beam_OLED.cfg b/T-Beam_OLED.cfg new file mode 100644 index 0000000..ac4b151 --- /dev/null +++ b/T-Beam_OLED.cfg @@ -0,0 +1,74 @@ +#define DEFAULT_AcftType 1 // [0..15] default aircraft-type: glider +#define DEFAULT_GeoidSepar 40 // [m] +#define DEFAULT_CONbaud 115200 +#define DEFAULT_PPSdelay 100 +#define DEFAULT_FreqPlan 0 + +// #define WITH_HELTEC // HELTEC module: PCB LED on GPI025 +// #define WITH_TTGO // TTGO module: PCB LED on GPIO2, GPIO25 free to use as DAC2 output +#define WITH_TBEAM // T-Beam module +// #define WITH_TBEAM_V10 // T-Beam module +// #define WITH_JACEK // JACEK ESP32 OGN-Tracker +// #define WITH_M5_JACEK // JACEK M5 ESP32 OGN-Tracker +// #define WITH_FollowMe // by Avionix + +// #define WITH_ILI9341 // 320x240 M5stack +// #define WITH_ST7789 // IPS 240x240 ST7789 +// #define WITH_TFT_LCD // TFT LCD +// #define WITH_OLED // OLED display on the I2C: some TTGO modules are without OLED display +// #define WITH_OLED2 // 2nd OLED display, I2C address next higher +#define WITH_U8G2_OLED // I2C OLED through the U8g2 library + +#ifdef WITH_JACEK +#define WITH_RFM69 // Jacek design uses RFM69 +#else +#define WITH_RFM95 // RF chip selection: both HELTEC and TTGO use sx1276 which is same as RFM95 +#endif + +// #define WITH_SLEEP // with software sleep mode controlled by the long-press on the button + +// #define WITH_AXP // with AXP192 power controller (T-BEAM V1.0) +// #define WITH_BQ // with BQ24295 power controller (FollowMe) + +// #define WITH_LED_RX +// #define WITH_LED_TX + +// #define WITH_GPS_ENABLE // use GPS_ENABLE control line to turn the GPS ON/OFF +// #define WITH_GPS_PPS // use the PPS signal from GPS for precise time-sync. +#define WITH_GPS_CONFIG // attempt to configure higher GPS baud rate and airborne mode + +#define WITH_GPS_UBX // GPS understands UBX +// #define WITH_GPS_MTK // GPS understands MTK +// #define WITH_GPS_SRF +// #define WITH_MAVLINK + +// #define WITH_GPS_UBX_PASS // to pass directly UBX packets to/from GPS +// #define WITH_GPS_NMEA_PASS // to pass directly NMEA to/from GPS + +// #define WITH_BMP180 // BMP180 pressure sensor +// #define WITH_BMP280 // BMP280 pressure sensor +#define WITH_BME280 // BMP280 with humidity (but still works with BMP280) +// #define WITH_MS5607 // MS5607 pressure sensor + +#define WITH_PFLAA // PFLAU and PFLAA for compatibility with XCsoar and LK8000 +// #define WITH_POGNT +#define WITH_LOOKOUT + +#define WITH_CONFIG // interpret the console input: $POGNS to change parameters + +#define WITH_BEEPER // with digital buzzer +// #define WITH_SOUND // with analog sound produced by DAC on pin 25 + +// #define WITH_KNOB +// #define WITH_VARIO + +// #define WITH_SD // use the SD card in SPI mode and FAT file system +#define WITH_SPIFFS // use SPIFFS file system in Flash +#define WITH_LOG // log own positions and other received to SPIFFS and possibly to uSD + +#define WITH_BT_SPP // Bluetooth serial port for smartphone/tablet link +// #define WITH_WIFI // attempt to connect to the wifi router for uploading the log files +// #define WITH_SPIFFS_LOG // log transmitted and received packets to SPIFFS + +#define WITH_ENCRYPT // Encrypt (optionally) the position + diff --git a/T-Beam_new_OLED.cfg b/T-Beam_new_OLED.cfg new file mode 100644 index 0000000..5abf0d2 --- /dev/null +++ b/T-Beam_new_OLED.cfg @@ -0,0 +1,75 @@ +#define DEFAULT_AcftType 1 // [0..15] default aircraft-type: glider +#define DEFAULT_GeoidSepar 40 // [m] +#define DEFAULT_CONbaud 115200 +#define DEFAULT_PPSdelay 100 +#define DEFAULT_FreqPlan 0 + +// #define WITH_HELTEC // HELTEC module: PCB LED on GPI025 +// #define WITH_TTGO // TTGO module: PCB LED on GPIO2, GPIO25 free to use as DAC2 output +// #define WITH_TBEAM // T-Beam module +#define WITH_TBEAM_V10 // T-Beam module +// #define WITH_JACEK // JACEK ESP32 OGN-Tracker +// #define WITH_M5_JACEK // JACEK M5 ESP32 OGN-Tracker +// #define WITH_FollowMe // by Avionix + +// #define WITH_ILI9341 // 320x240 M5stack +// #define WITH_ST7789 // IPS 240x240 ST7789 +// #define WITH_TFT_LCD // TFT LCD +// #define WITH_OLED // OLED display on the I2C: some TTGO modules are without OLED display +// #define WITH_OLED2 // 2nd OLED display, I2C address next higher +#define WITH_U8G2_OLED // I2C OLED through the U8g2 library + +#ifdef WITH_JACEK +#define WITH_RFM69 // Jacek design uses RFM69 +#else +#define WITH_RFM95 // RF chip selection: both HELTEC and TTGO use sx1276 which is same as RFM95 +#endif + +// #define WITH_SLEEP // with software sleep mode controlled by the long-press on the button + +#define WITH_AXP // with AXP192 power controller (T-BEAM V1.0) +// #define WITH_BQ // with BQ24295 power controller (FollowMe) + +// #define WITH_LED_RX +// #define WITH_LED_TX + +// #define WITH_GPS_ENABLE // use GPS_ENABLE control line to turn the GPS ON/OFF +#define WITH_GPS_PPS // use the PPS signal from GPS for precise time-sync. +#define WITH_GPS_CONFIG // attempt to configure higher GPS baud rate and airborne mode + +#define WITH_GPS_UBX // GPS understands UBX +// #define WITH_GPS_MTK // GPS understands MTK +// #define WITH_GPS_SRF +// #define WITH_MAVLINK + +// #define WITH_GPS_UBX_PASS // to pass directly UBX packets to/from GPS +// #define WITH_GPS_NMEA_PASS // to pass directly NMEA to/from GPS + +// #define WITH_BMP180 // BMP180 pressure sensor +// #define WITH_BMP280 // BMP280 pressure sensor +#define WITH_BME280 // BMP280 with humidity (but still works with BMP280) +// #define WITH_MS5607 // MS5607 pressure sensor + +// #define WITH_GDL90 +#define WITH_PFLAA // PFLAU and PFLAA for compatibility with XCsoar and LK8000 +// #define WITH_POGNT +#define WITH_LOOKOUT + +#define WITH_CONFIG // interpret the console input: $POGNS to change parameters + +#define WITH_BEEPER // with digital buzzer +// #define WITH_SOUND // with analog sound produced by DAC on pin 25 + +// #define WITH_KNOB +// #define WITH_VARIO + +// #define WITH_SD // use the SD card in SPI mode and FAT file system +#define WITH_SPIFFS // use SPIFFS file system in Flash +#define WITH_LOG // log own positions and other received to SPIFFS and possibly to uSD + +#define WITH_BT_SPP // Bluetooth serial port for smartphone/tablet link +// #define WITH_WIFI // attempt to connect to the wifi router for uploading the log files +// #define WITH_SPIFFS_LOG // log transmitted and received packets to SPIFFS + +// #define WITH_ENCRYPT // Encrypt (optionally) the position +