kopia lustrzana https://github.com/espressif/esp-idf
74 wiersze
3.2 KiB
Plaintext
74 wiersze
3.2 KiB
Plaintext
menu "Hardware Settings"
|
|
menu "MAC Config"
|
|
config ESP_MAC_ADDR_UNIVERSE_WIFI_STA
|
|
bool
|
|
|
|
config ESP_MAC_ADDR_UNIVERSE_WIFI_AP
|
|
bool
|
|
|
|
config ESP_MAC_ADDR_UNIVERSE_BT
|
|
bool
|
|
|
|
config ESP_MAC_ADDR_UNIVERSE_ETH
|
|
bool
|
|
|
|
# Insert chip-specific MAC config
|
|
rsource "./port/$IDF_TARGET/Kconfig.mac"
|
|
endmenu
|
|
|
|
menu "Sleep Config"
|
|
# This is here since this option affect behavior of esp_light_sleep_start
|
|
# regardless of power management configuration.
|
|
config ESP_SLEEP_POWER_DOWN_FLASH
|
|
bool "Power down flash in light sleep when there is no SPIRAM"
|
|
depends on !SPIRAM
|
|
default y
|
|
help
|
|
If enabled, chip will try to power down flash as part of esp_light_sleep_start(), which costs
|
|
more time when chip wakes up. Can only be enabled if there is no SPIRAM configured.
|
|
This option will in fact consider VDD_SDIO auto power value (ESP_PD_OPTION_AUTO) as OFF. Also, it is
|
|
possible to force a power domain to stay ON during light sleep by using esp_sleep_pd_config()
|
|
function.
|
|
|
|
config ESP_SLEEP_RTC_BUS_ISO_WORKAROUND
|
|
bool
|
|
default y if IDF_TARGET_ESP32 || IDF_TARGET_ESP32S2 || IDF_TARGET_ESP32S3
|
|
|
|
config ESP_SLEEP_GPIO_RESET_WORKAROUND
|
|
bool "light sleep GPIO reset workaround"
|
|
default y if IDF_TARGET_ESP32C3 || IDF_TARGET_ESP32S3
|
|
select PM_SLP_DISABLE_GPIO if FREERTOS_USE_TICKLESS_IDLE
|
|
help
|
|
esp32c3 and esp32s3 will reset at wake-up if GPIO is received a small electrostatic
|
|
pulse during light sleep, with specific condition
|
|
|
|
- GPIO needs to be configured as input-mode only
|
|
- The pin receives a small electrostatic pulse, and reset occurs when the pulse
|
|
voltage is higher than 6 V
|
|
|
|
For GPIO set to input mode only, it is not a good practice to leave it open/floating,
|
|
The hardware design needs to controlled it with determined supply or ground voltage
|
|
is necessary.
|
|
|
|
This option provides a software workaround for this issue. Configure to isolate all
|
|
GPIO pins in sleep state.
|
|
|
|
config ESP_SLEEP_PSRAM_LEAKAGE_WORKAROUND
|
|
bool "PSRAM leakage current workaround in light sleep"
|
|
depends on SPIRAM
|
|
help
|
|
When the CS pin of SPIRAM is not pulled up, the sleep current will
|
|
increase during light sleep. If the CS pin of SPIRAM has an external
|
|
pull-up, you do not need to select this option, otherwise, you
|
|
should enable this option.
|
|
|
|
config ESP_SLEEP_FLASH_LEAKAGE_WORKAROUND
|
|
bool "Flash leakage current workaround in light sleep"
|
|
help
|
|
When the CS pin of Flash is not pulled up, the sleep current will
|
|
increase during light sleep. If the CS pin of Flash has an external
|
|
pull-up, you do not need to select this option, otherwise, you
|
|
should enable this option.
|
|
endmenu
|
|
endmenu
|