kopia lustrzana https://github.com/espressif/esp-idf
281 wiersze
10 KiB
C
281 wiersze
10 KiB
C
// Copyright 2015-2016 Espressif Systems (Shanghai) PTE LTD
|
|
//
|
|
// Licensed under the Apache License, Version 2.0 (the "License");
|
|
// you may not use this file except in compliance with the License.
|
|
// You may obtain a copy of the License at
|
|
|
|
// http://www.apache.org/licenses/LICENSE-2.0
|
|
//
|
|
// Unless required by applicable law or agreed to in writing, software
|
|
// distributed under the License is distributed on an "AS IS" BASIS,
|
|
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
// See the License for the specific language governing permissions and
|
|
// limitations under the License.
|
|
#include <stddef.h>
|
|
#include <stdint.h>
|
|
#include "flash_qio_mode.h"
|
|
#include "esp_log.h"
|
|
#include "esp_err.h"
|
|
#include "rom/spi_flash.h"
|
|
#include "rom/efuse.h"
|
|
#include "soc/spi_struct.h"
|
|
#include "soc/efuse_reg.h"
|
|
#include "sdkconfig.h"
|
|
|
|
/* SPI flash controller */
|
|
#define SPIFLASH SPI1
|
|
|
|
/* SPI commands (actual on-wire commands not SPI controller bitmasks)
|
|
Suitable for use with the execute_flash_command static function.
|
|
*/
|
|
#define CMD_RDID 0x9F
|
|
#define CMD_WRSR 0x01
|
|
#define CMD_WRSR2 0x31 /* Not all SPI flash uses this command */
|
|
#define CMD_WREN 0x06
|
|
#define CMD_WRDI 0x04
|
|
#define CMD_RDSR 0x05
|
|
#define CMD_RDSR2 0x35 /* Not all SPI flash uses this command */
|
|
|
|
static const char *TAG = "qio_mode";
|
|
|
|
typedef unsigned (*read_status_fn_t)();
|
|
typedef void (*write_status_fn_t)(unsigned);
|
|
|
|
typedef struct __attribute__((packed)) {
|
|
const char *manufacturer;
|
|
uint8_t mfg_id; /* 8-bit JEDEC manufacturer ID */
|
|
uint16_t flash_id; /* 16-bit JEDEC flash chip ID */
|
|
uint16_t id_mask; /* Bits to match on in flash chip ID */
|
|
read_status_fn_t read_status_fn;
|
|
write_status_fn_t write_status_fn;
|
|
uint8_t status_qio_bit;
|
|
} qio_info_t;
|
|
|
|
/* Read 8 bit status using RDSR command */
|
|
static unsigned read_status_8b_rdsr();
|
|
/* Read 8 bit status (second byte) using RDSR2 command */
|
|
static unsigned read_status_8b_rdsr2();
|
|
/* read 16 bit status using RDSR & RDSR2 (low and high bytes) */
|
|
static unsigned read_status_16b_rdsr_rdsr2();
|
|
|
|
/* Write 8 bit status using WRSR */
|
|
static void write_status_8b_wrsr(unsigned new_status);
|
|
/* Write 8 bit status (second byte) using WRSR2 */
|
|
static void write_status_8b_wrsr2(unsigned new_status);
|
|
/* Write 16 bit status using WRSR */
|
|
static void write_status_16b_wrsr(unsigned new_status);
|
|
|
|
#define ESP32_D2WD_WP_GPIO 7 /* ESP32-D2WD has this GPIO wired to WP pin of flash */
|
|
|
|
#ifndef CONFIG_BOOTLOADER_SPI_WP_PIN // Set in menuconfig if SPI flasher config is set to a quad mode
|
|
#define CONFIG_BOOTLOADER_SPI_WP_PIN ESP32_D2WD_WP_GPIO
|
|
#endif
|
|
|
|
/* Array of known flash chips and data to enable Quad I/O mode
|
|
|
|
Manufacturer & flash ID can be tested by running "esptool.py
|
|
flash_id"
|
|
|
|
If manufacturer ID matches, and flash ID ORed with flash ID mask
|
|
matches, enable_qio_mode() will execute "Read Cmd", test if bit
|
|
number "QIE Bit" is set, and if not set it will call "Write Cmd"
|
|
with this bit set.
|
|
|
|
Searching of this table stops when the first match is found.
|
|
*/
|
|
const static qio_info_t chip_data[] = {
|
|
/* Manufacturer, mfg_id, flash_id, id mask, Read Status, Write Status, QIE Bit */
|
|
{ "MXIC", 0xC2, 0x2000, 0xFF00, read_status_8b_rdsr, write_status_8b_wrsr, 6 },
|
|
{ "ISSI", 0x9D, 0x4000, 0xCF00, read_status_8b_rdsr, write_status_8b_wrsr, 6 }, /* IDs 0x40xx, 0x70xx */
|
|
{ "WinBond", 0xEF, 0x4000, 0xFF00, read_status_16b_rdsr_rdsr2, write_status_16b_wrsr, 9 },
|
|
{ "GD", 0xC8, 0x6000, 0xFF00, read_status_16b_rdsr_rdsr2, write_status_16b_wrsr, 9 },
|
|
|
|
/* Final entry is default entry, if no other IDs have matched.
|
|
|
|
This approach works for chips including:
|
|
GigaDevice (mfg ID 0xC8, flash IDs including 4016),
|
|
FM25Q32 (QOUT mode only, mfg ID 0xA1, flash IDs including 4016)
|
|
*/
|
|
{ NULL, 0xFF, 0xFFFF, 0xFFFF, read_status_8b_rdsr2, write_status_8b_wrsr2, 1 },
|
|
};
|
|
|
|
#define NUM_CHIPS (sizeof(chip_data) / sizeof(qio_info_t))
|
|
|
|
static esp_err_t enable_qio_mode(read_status_fn_t read_status_fn,
|
|
write_status_fn_t write_status_fn,
|
|
uint8_t status_qio_bit);
|
|
|
|
/* Generic function to use the "user command" SPI controller functionality
|
|
to send commands to the SPI flash and read the respopnse.
|
|
|
|
The command passed here is always the on-the-wire command given to the SPI flash unit.
|
|
*/
|
|
static uint32_t execute_flash_command(uint8_t command, uint32_t mosi_data, uint8_t mosi_len, uint8_t miso_len);
|
|
|
|
/* dummy_len_plus values defined in ROM for SPI flash configuration */
|
|
extern uint8_t g_rom_spiflash_dummy_len_plus[];
|
|
|
|
void bootloader_enable_qio_mode(void)
|
|
{
|
|
uint32_t old_ctrl_reg;
|
|
uint32_t raw_flash_id;
|
|
uint8_t mfg_id;
|
|
uint16_t flash_id;
|
|
int i;
|
|
|
|
ESP_LOGD(TAG, "Probing for QIO mode enable...");
|
|
esp_rom_spiflash_wait_idle(&g_rom_flashchip);
|
|
|
|
/* Set up some of the SPIFLASH user/ctrl variables which don't change
|
|
while we're probing using execute_flash_command() */
|
|
old_ctrl_reg = SPIFLASH.ctrl.val;
|
|
SPIFLASH.ctrl.val = SPI_WP_REG; // keep WP high while idle, otherwise leave DIO mode
|
|
SPIFLASH.user.usr_dummy = 0;
|
|
SPIFLASH.user.usr_addr = 0;
|
|
SPIFLASH.user.usr_command = 1;
|
|
SPIFLASH.user2.usr_command_bitlen = 7;
|
|
|
|
raw_flash_id = execute_flash_command(CMD_RDID, 0, 0, 24);
|
|
ESP_LOGD(TAG, "Raw SPI flash chip id 0x%x", raw_flash_id);
|
|
|
|
mfg_id = raw_flash_id & 0xFF;
|
|
flash_id = (raw_flash_id >> 16) | (raw_flash_id & 0xFF00);
|
|
ESP_LOGD(TAG, "Manufacturer ID 0x%02x chip ID 0x%04x", mfg_id, flash_id);
|
|
|
|
for (i = 0; i < NUM_CHIPS-1; i++) {
|
|
const qio_info_t *chip = &chip_data[i];
|
|
if (mfg_id == chip->mfg_id && (flash_id & chip->id_mask) == (chip->flash_id & chip->id_mask)) {
|
|
ESP_LOGI(TAG, "Enabling QIO for flash chip %s", chip_data[i].manufacturer);
|
|
break;
|
|
}
|
|
}
|
|
|
|
if (i == NUM_CHIPS - 1) {
|
|
ESP_LOGI(TAG, "Enabling default flash chip QIO");
|
|
}
|
|
|
|
esp_err_t res = enable_qio_mode(chip_data[i].read_status_fn,
|
|
chip_data[i].write_status_fn,
|
|
chip_data[i].status_qio_bit);
|
|
if (res != ESP_OK) {
|
|
// Restore SPI flash CTRL setting, to keep us in DIO/DOUT mode
|
|
SPIFLASH.ctrl.val = old_ctrl_reg;
|
|
}
|
|
}
|
|
|
|
static esp_err_t enable_qio_mode(read_status_fn_t read_status_fn,
|
|
write_status_fn_t write_status_fn,
|
|
uint8_t status_qio_bit)
|
|
{
|
|
uint32_t status;
|
|
const uint32_t spiconfig = ets_efuse_get_spiconfig();
|
|
|
|
if (spiconfig != EFUSE_SPICONFIG_SPI_DEFAULTS && spiconfig != EFUSE_SPICONFIG_HSPI_DEFAULTS) {
|
|
// spiconfig specifies a custom efuse pin configuration. This config defines all pins -except- WP,
|
|
// which is compiled into the bootloader instead.
|
|
//
|
|
// Most commonly an overriden pin mapping means ESP32-D2WD. Warn if chip is ESP32-D2WD
|
|
// but someone has changed the WP pin assignment from that chip's WP pin.
|
|
uint32_t chip_ver = REG_GET_FIELD(EFUSE_BLK0_RDATA3_REG, EFUSE_RD_CHIP_VER_RESERVE);
|
|
uint32_t pkg_ver = chip_ver & 0x7;
|
|
const int PKG_VER_ESP32_D2WD = 2; // TODO: use chip detection API once available
|
|
if (pkg_ver == PKG_VER_ESP32_D2WD && CONFIG_BOOTLOADER_SPI_WP_PIN != ESP32_D2WD_WP_GPIO) {
|
|
ESP_LOGW(TAG, "Chip is ESP32-D2WD but flash WP pin is different value to internal flash");
|
|
}
|
|
}
|
|
|
|
esp_rom_spiflash_wait_idle(&g_rom_flashchip);
|
|
|
|
status = read_status_fn();
|
|
ESP_LOGD(TAG, "Initial flash chip status 0x%x", status);
|
|
|
|
if ((status & (1<<status_qio_bit)) == 0) {
|
|
execute_flash_command(CMD_WREN, 0, 0, 0);
|
|
write_status_fn(status | (1<<status_qio_bit));
|
|
|
|
esp_rom_spiflash_wait_idle(&g_rom_flashchip);
|
|
|
|
status = read_status_fn();
|
|
ESP_LOGD(TAG, "Updated flash chip status 0x%x", status);
|
|
if ((status & (1<<status_qio_bit)) == 0) {
|
|
ESP_LOGE(TAG, "Failed to set QIE bit, not enabling QIO mode");
|
|
return ESP_FAIL;
|
|
}
|
|
|
|
} else {
|
|
ESP_LOGD(TAG, "QIO mode already enabled in flash");
|
|
}
|
|
|
|
ESP_LOGD(TAG, "Enabling QIO mode...");
|
|
|
|
esp_rom_spiflash_read_mode_t mode;
|
|
#if CONFIG_FLASHMODE_QOUT
|
|
mode = ESP_ROM_SPIFLASH_QOUT_MODE;
|
|
#else
|
|
mode = ESP_ROM_SPIFLASH_QIO_MODE;
|
|
#endif
|
|
|
|
esp_rom_spiflash_config_readmode(mode);
|
|
|
|
esp_rom_spiflash_select_qio_pins(CONFIG_BOOTLOADER_SPI_WP_PIN, spiconfig);
|
|
|
|
return ESP_OK;
|
|
}
|
|
|
|
static unsigned read_status_8b_rdsr()
|
|
{
|
|
return execute_flash_command(CMD_RDSR, 0, 0, 8);
|
|
}
|
|
|
|
static unsigned read_status_8b_rdsr2()
|
|
{
|
|
return execute_flash_command(CMD_RDSR2, 0, 0, 8);
|
|
}
|
|
|
|
static unsigned read_status_16b_rdsr_rdsr2()
|
|
{
|
|
return execute_flash_command(CMD_RDSR, 0, 0, 8) | (execute_flash_command(CMD_RDSR2, 0, 0, 8) << 8);
|
|
}
|
|
|
|
static void write_status_8b_wrsr(unsigned new_status)
|
|
{
|
|
execute_flash_command(CMD_WRSR, new_status, 8, 0);
|
|
}
|
|
|
|
static void write_status_8b_wrsr2(unsigned new_status)
|
|
{
|
|
execute_flash_command(CMD_WRSR2, new_status, 8, 0);
|
|
}
|
|
|
|
static void write_status_16b_wrsr(unsigned new_status)
|
|
{
|
|
execute_flash_command(CMD_WRSR, new_status, 16, 0);
|
|
}
|
|
|
|
static uint32_t execute_flash_command(uint8_t command, uint32_t mosi_data, uint8_t mosi_len, uint8_t miso_len)
|
|
{
|
|
SPIFLASH.user2.usr_command_value = command;
|
|
SPIFLASH.user.usr_miso = miso_len > 0;
|
|
SPIFLASH.miso_dlen.usr_miso_dbitlen = miso_len ? (miso_len - 1) : 0;
|
|
SPIFLASH.user.usr_mosi = mosi_len > 0;
|
|
SPIFLASH.mosi_dlen.usr_mosi_dbitlen = mosi_len ? (mosi_len - 1) : 0;
|
|
SPIFLASH.data_buf[0] = mosi_data;
|
|
|
|
if (g_rom_spiflash_dummy_len_plus[1]) {
|
|
/* When flash pins are mapped via GPIO matrix, need a dummy cycle before reading via MISO */
|
|
if (miso_len > 0) {
|
|
SPIFLASH.user.usr_dummy = 1;
|
|
SPIFLASH.user1.usr_dummy_cyclelen = g_rom_spiflash_dummy_len_plus[1] - 1;
|
|
} else {
|
|
SPIFLASH.user.usr_dummy = 0;
|
|
SPIFLASH.user1.usr_dummy_cyclelen = 0;
|
|
}
|
|
}
|
|
|
|
SPIFLASH.cmd.usr = 1;
|
|
while(SPIFLASH.cmd.usr != 0)
|
|
{ }
|
|
|
|
return SPIFLASH.data_buf[0];
|
|
}
|