esp-idf/examples/system/console/basic

Basic Console Example (esp_console_repl)

(See the README.md file in the upper level 'examples' directory for more information about examples.)

This example illustrates the usage of the REPL (Read-Eval-Print Loop) APIs of the Console Component to create an interactive shell on the ESP chip. The interactive shell running on the ESP chip can then be controlled/interacted with over a serial interface. This example supports UART and USB interfaces.

The interactive shell implemented in this example contains a wide variety of commands, and can act as a basis for applications that require a command-line interface (CLI).

Compared to the advanced console example, this example requires less code to initialize and run the console. esp_console_repl API handles most of the details. If you'd like to customize the way console works (for example, process console commands in an existing task), please check the advanced console example.

How to use example

This example can be used on boards with UART and USB interfaces. The sections below explain how to set up the board and configure the example.

Using with UART

When UART interface is used, this example should run on any commonly available Espressif development board. UART interface is enabled by default (CONFIG_ESP_CONSOLE_UART_DEFAULT option in menuconfig). No extra configuration is required.

Using with USB_SERIAL_JTAG

On chips with USB_SERIAL_JTAG peripheral, console example can be used over the USB serial port.

• First, connect the USB cable to the USB_SERIAL_JTAG interface.
• Second, run idf.py menuconfig and enable CONFIG_ESP_CONSOLE_USB_SERIAL_JTAG option.

For more details about connecting and configuring USB_SERIAL_JTAG (including pin numbers), see the IDF Programming Guide:

• ESP32-C3 USB_SERIAL_JTAG
• ESP32-S3 USB_SERIAL_JTAG

Using with USB CDC (USB_OTG peripheral)

USB_OTG peripheral can also provide a USB serial port which works with this example.

• First, connect the USB cable to the USB_OTG peripheral interface.
• Second, run idf.py menuconfig and enable CONFIG_ESP_CONSOLE_USB_CDC option.

For more details about connecting and configuring USB_OTG (including pin numbers), see the IDF Programming Guide:

• ESP32-S2 USB_OTG
• ESP32-S3 USB_OTG

Other configuration options

This example has an option to store the command history in Flash. This option is enabled by default.

To disable this, run idf.py menuconfig and disable CONFIG_CONSOLE_STORE_HISTORY option.

Build and Flash

Build the project and flash it to the board, then run monitor tool to view serial output:

idf.py -p PORT flash monitor

(Replace PORT with the name of the serial port to use.)

(To exit the serial monitor, type Ctrl-].)

See the Getting Started Guide for full steps to configure and use ESP-IDF to build projects.

Example Output

Enter the help command get a full list of all available commands. The following is a sample session of the Console Example where a variety of commands provided by the Console Example are used.

On ESP32, GPIO15 may be connected to GND to remove the boot log output.

This is an example of ESP-IDF console component.
Type 'help' to get the list of commands.
Use UP/DOWN arrows to navigate through command history.
Press TAB when typing command name to auto-complete.
[esp32]> help
help 
  Print the list of registered commands

free 
  Get the total size of heap memory available

restart 
  Restart the program

deep_sleep  [-t <t>] [--io=<n>] [--io_level=<0|1>]
  Enter deep sleep mode. Two wakeup modes are supported: timer and GPIO. If no
  wakeup option is specified, will sleep indefinitely.
  -t, --time=<t>  Wake up time, ms
      --io=<n>  If specified, wakeup using GPIO with given number
  --io_level=<0|1>  GPIO level to trigger wakeup

join  [--timeout=<t>] <ssid> [<pass>]
  Join WiFi AP as a station
  --timeout=<t>  Connection timeout, ms
        <ssid>  SSID of AP
        <pass>  PSK of AP

[esp32]> free
257200
[esp32]> deep_sleep -t 1000
I (146929) deep_sleep: Enabling timer wakeup, timeout=1000000us
I (619) heap_init: Initializing. RAM available for dynamic allocation:
I (620) heap_init: At 3FFAE2A0 len 00001D60 (7 KiB): DRAM
I (626) heap_init: At 3FFB7EA0 len 00028160 (160 KiB): DRAM
I (645) heap_init: At 3FFE0440 len 00003BC0 (14 KiB): D/IRAM
I (664) heap_init: At 3FFE4350 len 0001BCB0 (111 KiB): D/IRAM
I (684) heap_init: At 40093EA8 len 0000C158 (48 KiB): IRAM

This is an example of ESP-IDF console component.
Type 'help' to get the list of commands.
Use UP/DOWN arrows to navigate through command history.
Press TAB when typing command name to auto-complete.
[esp32]> join --timeout 10000 test_ap test_password
I (182639) connect: Connecting to 'test_ap'
I (184619) connect: Connected
[esp32]> free
212328
[esp32]> restart
I (205639) restart: Restarting
I (616) heap_init: Initializing. RAM available for dynamic allocation:
I (617) heap_init: At 3FFAE2A0 len 00001D60 (7 KiB): DRAM
I (623) heap_init: At 3FFB7EA0 len 00028160 (160 KiB): DRAM
I (642) heap_init: At 3FFE0440 len 00003BC0 (14 KiB): D/IRAM
I (661) heap_init: At 3FFE4350 len 0001BCB0 (111 KiB): D/IRAM
I (681) heap_init: At 40093EA8 len 0000C158 (48 KiB): IRAM

This is an example of ESP-IDF console component.
Type 'help' to get the list of commands.
Use UP/DOWN arrows to navigate through command history.
Press TAB when typing command name to auto-complete.
[esp32]> 

Troubleshooting

Line Endings

The line endings in the Console Example are configured to match particular serial monitors. Therefore, if the following log output appears, consider using a different serial monitor (e.g. Putty for Windows) or modify the example's UART configuration.

This is an example of ESP-IDF console component.
Type 'help' to get the list of commands.
Use UP/DOWN arrows to navigate through command history.
Press TAB when typing command name to auto-complete.
Your terminal application does not support escape sequences.
Line editing and history features are disabled.
On Windows, try using Putty instead.
esp32>