![]() 1. Add command for Ethernet based on console component. 2. Make cmd_system and iperf a component that can be referenced by other examples 3. Add "version" command to cmd_system.c 4. Clean up the README.md in all ethernet examples[TW#26525] |
||
---|---|---|
.. | ||
main | ||
CMakeLists.txt | ||
Makefile | ||
README.md | ||
partitions_example.csv | ||
sdkconfig.defaults |
README.md
Ethernet iperf example
(See the README.md file in the upper level 'examples' directory for more information about examples.)
Overview
This example demonstrates basic usage of iperf protocol to measure the throughout/bandwidth of Ethernet.
This example is based on esp-idf's console component. For more information about console you can read the guide.
How to use example
Prepare work
- Install iperf tool on PC
- Debian/Ubuntu:
sudo apt-get install iperf
- macOS:
brew install iperf
(if using Homebrew) orsudo port install iperf
(if using MacPorts) - Windows(MSYS2): Downloads binaries from here
- Debian/Ubuntu:
- Initialise Ethernet on ESP32, run
ethernet start
- Get ip information(optional), run
ethernet info
Configure the project
Enter make menuconfig
if you are using GNU Make based build system or enter idf.py menuconfig
if you' are using CMake based build system. Then go into Example Configuration
menu.
-
Check whether or not to store the history command into flash under
Store command history in flash
option -
Set PHY address under
PHY address
option, this address depends on the hardware and the PHY configuration. Consult the documentation/datasheet for the PHY hardware you have.- Address 31 (default) for Espressif's Ethernet board with TLK110 PHY by default
- Address 1 for the common Waveshare LAN8720 PHY breakout
- Address 0 for other LAN8720 breakouts
-
Check whether or not to control PHY's power (if true, you need also to set PHY Power GPIO number later)
-
Set SMI MDC/MDIO GPIO number according to board schemetic, default these two GPIOs are set as below:
Default Example GPIO RMII Signal Notes GPIO23 MDC Output to PHY GPIO18 MDIO Bidirectional -
Select one kind of EMAC clock mode under
EMAC clock mode
option. Possible configurations of the clock are listed as below:Mode GPIO Pin Signal name Notes external GPIO0 EMAC_TX_CLK Input of 50MHz PHY clock internal GPIO16 EMAC_CLK_OUT Output of 50MHz APLL clock internal GPIO17 EMAC_CLK_180 Inverted output of 50MHz APLL clock (suitable for long clock trace) - The external reference clock of 50MHz must be supplied on
GPIO0
. - The ESP32 can generate a 50MHz clock using its APLL. When the APLL is already used as clock source for other purposes (most likely I²S), you have no choice but choose external clock.
- The external reference clock of 50MHz must be supplied on
Build and Flash
Enter make -j4 flash monitor
if you are using GNU Make based build system or enter idf.py build flash monitor
if you' are using CMake based build system.
(To exit the serial monitor, type Ctrl-]
.)
See the Getting Started Guide for full steps to configure and use ESP-IDF to build projects.
Example Output
Test uplink bandwidth
- PC: run command:
iperf -u -s -i 3
to start iperf server in UDP mode, and report interval is 3 seconds. - ESP32: run command:
iperf -u -c PC_IP -i 3 -t 30
to start iperf client in UDP mode, and the test will last 30 seconds.
PC output
------------------------------------------------------------
Server listening on UDP port 5001
Receiving 1470 byte datagrams
UDP buffer size: 208 KByte (default)
------------------------------------------------------------
[ 3] local 192.168.2.160 port 5001 connected with 192.168.2.156 port 49154
[ ID] Interval Transfer Bandwidth Jitter Lost/Total Datagrams
[ 3] 0.0- 3.0 sec 24.8 MBytes 69.5 Mbits/sec 0.172 ms 1/17721 (0.0056%)
[ 3] 3.0- 6.0 sec 24.8 MBytes 69.5 Mbits/sec 0.169 ms 0/17719 (0%)
[ 3] 6.0- 9.0 sec 24.8 MBytes 69.5 Mbits/sec 0.170 ms 0/17719 (0%)
[ 3] 9.0-12.0 sec 24.8 MBytes 69.5 Mbits/sec 0.170 ms 0/17718 (0%)
[ 3] 12.0-15.0 sec 24.8 MBytes 69.5 Mbits/sec 0.169 ms 0/17717 (0%)
[ 3] 15.0-18.0 sec 24.8 MBytes 69.5 Mbits/sec 0.170 ms 0/17720 (0%)
[ 3] 18.0-21.0 sec 24.8 MBytes 69.5 Mbits/sec 0.170 ms 0/17721 (0%)
[ 3] 21.0-24.0 sec 24.8 MBytes 69.5 Mbits/sec 0.169 ms 0/17720 (0%)
[ 3] 24.0-27.0 sec 24.8 MBytes 69.5 Mbits/sec 0.169 ms 0/17723 (0%)
ESP32 output
mode=udp-client sip=192.168.2.156:5001, dip=192.168.2.160:5001, interval=3, time=30
Interval Bandwidth
0- 3 sec 69.34 Mbits/sec
3- 6 sec 69.55 Mbits/sec
6- 9 sec 69.55 Mbits/sec
9- 12 sec 69.55 Mbits/sec
12- 15 sec 69.55 Mbits/sec
15- 18 sec 69.56 Mbits/sec
18- 21 sec 69.56 Mbits/sec
21- 24 sec 69.56 Mbits/sec
24- 27 sec 69.56 Mbits/sec
27- 30 sec 69.56 Mbits/sec
Test downlink bandwidth
- PC: run command:
iperf -u -c ESP_IP -b 80M -t 30 -i 3
to start iperf client in UDP mode with estimated bandwidth 100M, and report interval is 3 seconds. - ESP32: run command:
iperf -u -s -t 30 -i 3
to start iperf server in UDP mode, and the test will last 30 seconds.
PC output
------------------------------------------------------------
Client connecting to 192.168.2.156, UDP port 5001
Sending 1470 byte datagrams
UDP buffer size: 208 KByte (default)
------------------------------------------------------------
[ 3] local 192.168.2.160 port 59581 connected with 192.168.2.156 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0- 3.0 sec 28.6 MBytes 80.0 Mbits/sec
[ 3] 3.0- 6.0 sec 28.6 MBytes 80.0 Mbits/sec
[ 3] 6.0- 9.0 sec 28.6 MBytes 80.0 Mbits/sec
[ 3] 9.0-12.0 sec 28.6 MBytes 80.0 Mbits/sec
[ 3] 12.0-15.0 sec 28.6 MBytes 79.9 Mbits/sec
[ 3] 15.0-18.0 sec 28.6 MBytes 80.0 Mbits/sec
[ 3] 18.0-21.0 sec 28.6 MBytes 80.0 Mbits/sec
[ 3] 21.0-24.0 sec 28.6 MBytes 80.0 Mbits/sec
[ 3] 24.0-27.0 sec 28.6 MBytes 80.0 Mbits/sec
ESP32 output
mode=udp-server sip=192.168.2.156:5001, dip=0.0.0.0:5001, interval=3, time=30
Interval Bandwidth
I (2534456) iperf: want recv=16384
0- 30 sec 72.67 Mbits/sec
3- 6 sec 74.18 Mbits/sec
6- 9 sec 73.14 Mbits/sec
9- 12 sec 73.65 Mbits/sec
12- 15 sec 72.87 Mbits/sec
15- 18 sec 73.29 Mbits/sec
18- 21 sec 74.35 Mbits/sec
21- 24 sec 72.28 Mbits/sec
24- 27 sec 73.39 Mbits/sec
27- 30 sec 73.49 Mbits/sec
Suggestions of getting higher bandwidth
- Higher MCU working frequency will get higher bandwidth
- Put frequency invoked function into IRAM via macro
IRAM_ATTR
in code. - Priority of iperf task may also have effect.
Troubleshooting
-
If the PHY address is incorrect then the EMAC will still be initialised, but all attempts to read/write configuration registers in the PHY's register will fail, for example, waiting for auto-negotiation done.
-
Check PHY Clock
The ESP32's MAC and the External PHY device need a common 50MHz reference clock. This clock can either be provided externally by a crystal oscillator (e.g. crystal connected to the PHY or a seperate crystal oscillator) or internally by generating from EPS32's APLL. The signal integrity of this clock is strict, so it is highly recommended to add a 33Ω resistor in series to reduce ringing.
-
Check GPIO connections, the RMII PHY wiring is fixed which can not be changed through either IOMUX or GPIO Matrix. They're described as below:
GPIO RMII Signal ESP32 EMAC Function GPIO21 TX_EN EMAC_TX_EN GPIO19 TX0 EMAC_TXD0 GPIO22 TX1 EMAC_TXD1 GPIO25 RX0 EMAC_RXD0 GPIO26 RX1 EMAC_RXD1 GPIO27 CRS_DV EMAC_RX_DRV -
Check GPIO0
GPIO0 is a strapping pin for entering UART flashing mode on reset, care must be taken when using this pin as
EMAC_TX_CLK
. If the clock output from the PHY is oscillating during reset, the ESP32 may randomly enter UART flashing mode. One solution is to use an additional GPIO as a "power pin", which either powers the PHY on/off or enables/disables the PHY's own oscillator. This prevents the clock signal from being active during a system reset. For this configuration to work,GPIO0
also needs a pullup resistor and the "power pin" GPIO will need a pullup/pulldown resistor - as appropriate in order to keep the PHY clock disabled when the ESP32 is in reset. See the example source code to see how the "power pin" GPIO can be managed in software. The example defaults to usingGPIO17
for this function, but it can be overriden. On Espressif's Ethernet development board,GPIO17
is the power pin used to enable/disable the PHY oscillator.