…
|
||
---|---|---|
.. | ||
main | ||
tutorial | ||
CMakeLists.txt | ||
README.md | ||
sdkconfig.defaults | ||
sdkconfig.defaults.esp32c2 | ||
sdkconfig.defaults.esp32c3 | ||
sdkconfig.defaults.esp32h4 | ||
sdkconfig.defaults.esp32s3 |
README.md
Supported Targets | ESP32 | ESP32-C2 | ESP32-C3 | ESP32-H4 | ESP32-S3 |
---|
ESP-IDF Gatt Security Client Example
This example shows how to use the ESP BLE security APIs to secure connect to and encrypt with peer devices.
How to Use Example
Before project configuration and build, be sure to set the correct chip target using:
idf.py set-target <chip_name>
To test this demo, you can run the gatt_security_server_demo, which starts advertising and can be connected to this demo automatically.
There are some important points for this demo:
esp_ble_gap_set_security_param
should be used to set the security parameters in the initial stage;esp_ble_set_encryption
should be used to start encryption with peer device. If the peer device initiates the encryption,esp_ble_gap_security_rsp
should be used to send security response to the peer device whenESP_GAP_BLE_SEC_REQ_EVT
is received.- The
gatt_security_client_demo
will receive aESP_GAP_BLE_AUTH_CMPL_EVT
once the encryption procedure has completed.
Please, check this tutorial for more information about this example.
Hardware Required
- A development board with ESP32/ESP32-C3/ESP32-C2/ESP32-H4/ESP32-S3 SoC (e.g., ESP32-DevKitC, ESP-WROVER-KIT, etc.)
- A USB cable for Power supply and programming
See Development Boards for more information about it.
Build and Flash
Run idf.py -p PORT flash monitor
to build, flash and monitor the project.
(To exit the serial monitor, type Ctrl-]
.)
See the Getting Started Guide for full steps to configure and use ESP-IDF to build projects.
Example Output
I (0) cpu_start: Starting scheduler on APP CPU.
I (572) BTDM_INIT: BT controller compile version [1342a48]
I (572) system_api: Base MAC address is not set
I (572) system_api: read default base MAC address from EFUSE
I (582) phy_init: phy_version 4670,719f9f6,Feb 18 2021,17:07:07
I (1002) SEC_GATTC_DEMO: EVT 0, gattc if 1
I (1002) SEC_GATTC_DEMO: REG_EVT
I (1032) SEC_GATTC_DEMO: Scan start success
I (1242) SEC_GATTC_DEMO: 38 68 a4 69 bb 7c
I (1242) SEC_GATTC_DEMO: Searched Adv Data Len 31, Scan Response Len 14
I (1242) SEC_GATTC_DEMO: Searched Device Name Len 0
I (1242) SEC_GATTC_DEMO:
I (1262) SEC_GATTC_DEMO: 38 68 a4 69 bb 7c
I (1262) SEC_GATTC_DEMO: Searched Adv Data Len 31, Scan Response Len 14
I (1262) SEC_GATTC_DEMO: Searched Device Name Len 0
I (1272) SEC_GATTC_DEMO:
I (1592) SEC_GATTC_DEMO: 38 68 a4 69 bb 7c
I (1592) SEC_GATTC_DEMO: Searched Adv Data Len 31, Scan Response Len 14
I (1592) SEC_GATTC_DEMO: Searched Device Name Len 0
I (1602) SEC_GATTC_DEMO:
I (1912) SEC_GATTC_DEMO: 38 68 a4 69 bb 7c
I (1912) SEC_GATTC_DEMO: Searched Adv Data Len 31, Scan Response Len 14
I (1912) SEC_GATTC_DEMO: Searched Device Name Len 0
I (1922) SEC_GATTC_DEMO:
Troubleshooting
For any technical queries, please open an issue on GitHub. We will get back to you soon.