esp-idf/components/esp_adc_cal/include/esp_adc_cal.h

153 wiersze
6.4 KiB
C

// Copyright 2015-2016 Espressif Systems (Shanghai) PTE LTD
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
// http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
#ifndef __ESP_ADC_CAL_H__
#define __ESP_ADC_CAL_H__
#ifdef __cplusplus
extern "C" {
#endif
#include <stdint.h>
#include "esp_err.h"
#include "driver/adc.h"
/**
* @brief Type of calibration value used in characterization
*/
typedef enum {
ESP_ADC_CAL_VAL_EFUSE_VREF = 0, /**< Characterization based on reference voltage stored in eFuse*/
ESP_ADC_CAL_VAL_EFUSE_TP = 1, /**< Characterization based on Two Point values stored in eFuse*/
ESP_ADC_CAL_VAL_DEFAULT_VREF = 2, /**< Characterization based on default reference voltage*/
} esp_adc_cal_value_t;
/**
* @brief Structure storing characteristics of an ADC
*
* @note Call esp_adc_cal_characterize() to initialize the structure
*/
typedef struct {
adc_unit_t adc_num; /**< ADC number*/
adc_atten_t atten; /**< ADC attenuation*/
adc_bits_width_t bit_width; /**< ADC bit width */
uint32_t coeff_a; /**< Gradient of ADC-Voltage curve*/
uint32_t coeff_b; /**< Offset of ADC-Voltage curve*/
uint32_t vref; /**< Vref used by lookup table*/
const uint32_t *low_curve; /**< Pointer to low Vref curve of lookup table (NULL if unused)*/
const uint32_t *high_curve; /**< Pointer to high Vref curve of lookup table (NULL if unused)*/
} esp_adc_cal_characteristics_t;
/**
* @brief Checks if ADC calibration values are burned into eFuse
*
* This function checks if ADC reference voltage or Two Point values have been
* burned to the eFuse of the current ESP32
*
* @param value_type Type of calibration value (ESP_ADC_CAL_VAL_EFUSE_VREF or ESP_ADC_CAL_VAL_EFUSE_TP)
*
* @return
* - ESP_OK: The calibration mode is supported in eFuse
* - ESP_ERR_NOT_SUPPORTED: Error, eFuse values are not burned
* - ESP_ERR_INVALID_ARG: Error, invalid argument (ESP_ADC_CAL_VAL_DEFAULT_VREF)
*/
esp_err_t esp_adc_cal_check_efuse(esp_adc_cal_value_t value_type);
/**
* @brief Characterize an ADC at a particular attenuation
*
* This function will characterize the ADC at a particular attenuation and generate
* the ADC-Voltage curve in the form of [y = coeff_a * x + coeff_b].
* Characterization can be based on Two Point values, eFuse Vref, or default Vref
* and the calibration values will be prioritized in that order.
*
* @note Two Point values and eFuse Vref can be enabled/disabled using menuconfig.
*
* @param[in] adc_num ADC to characterize (ADC_UNIT_1 or ADC_UNIT_2)
* @param[in] atten Attenuation to characterize
* @param[in] bit_width Bit width configuration of ADC
* @param[in] default_vref Default ADC reference voltage in mV (used if eFuse values is not available)
* @param[out] chars Pointer to empty structure used to store ADC characteristics
*
* @return
* - ESP_ADC_CAL_VAL_EFUSE_VREF: eFuse Vref used for characterization
* - ESP_ADC_CAL_VAL_EFUSE_TP: Two Point value used for characterization (only in Linear Mode)
* - ESP_ADC_CAL_VAL_DEFAULT_VREF: Default Vref used for characterization
*/
esp_adc_cal_value_t esp_adc_cal_characterize(adc_unit_t adc_num,
adc_atten_t atten,
adc_bits_width_t bit_width,
uint32_t default_vref,
esp_adc_cal_characteristics_t *chars);
/**
* @brief Convert an ADC reading to voltage in mV
*
* This function converts an ADC reading to a voltage in mV based on the ADC's
* characteristics.
*
* @note Characteristics structure must be initialized before this function
* is called (call esp_adc_cal_characterize())
*
* @param[in] adc_reading ADC reading
* @param[in] chars Pointer to initialized structure containing ADC characteristics
*
* @return Voltage in mV
*/
uint32_t esp_adc_cal_raw_to_voltage(uint32_t adc_reading, const esp_adc_cal_characteristics_t *chars);
/**
* @brief Reads an ADC and converts the reading to a voltage in mV
*
* This function reads an ADC then converts the raw reading to a voltage in mV
* based on the characteristics provided. The ADC that is read is also
* determined by the characteristics.
*
* @note The Characteristics structure must be initialized before this
* function is called (call esp_adc_cal_characterize())
*
* @param[in] channel ADC Channel to read
* @param[in] chars Pointer to initialized ADC characteristics structure
* @param[out] voltage Pointer to store converted voltage
*
* @return
* - ESP_OK: ADC read and converted to mV
* - ESP_ERR_TIMEOUT: Error, timed out attempting to read ADC
* - ESP_ERR_INVALID_ARG: Error due to invalid arguments
*/
esp_err_t esp_adc_cal_get_voltage(adc_channel_t channel, const esp_adc_cal_characteristics_t *chars, uint32_t *voltage);
/* -------------------------- Deprecated API ------------------------------- */
/** @cond */ //Doxygen command to hide deprecated function from API Reference
/**
* @deprecated ADC1 characterization function. Deprecated in order to accommodate
* ADC2 and eFuse functionality. Use esp_adc_cal_characterize() instead
*/
void esp_adc_cal_get_characteristics(uint32_t vref, adc_atten_t atten, adc_bits_width_t bit_width, esp_adc_cal_characteristics_t *chars) __attribute__((deprecated));
/*
* @deprecated This function reads ADC1 and returns the corrected voltage. This
* has been deprecated in order to accommodate ADC2 support. Use the
* new function esp_adc_cal_get_voltage() instead.
*/
uint32_t adc1_to_voltage(adc1_channel_t channel, const esp_adc_cal_characteristics_t *chars) __attribute__((deprecated));
/** @endcond */
#ifdef __cplusplus
}
#endif
#endif /* __ESP_ADC_CAL_H__ */