kopia lustrzana https://github.com/espressif/esp-idf
570 wiersze
21 KiB
C
570 wiersze
21 KiB
C
// Copyright 2010-2016 Espressif Systems (Shanghai) PTE LTD
|
|
//
|
|
// Licensed under the Apache License, Version 2.0 (the "License");
|
|
// you may not use this file except in compliance with the License.
|
|
// You may obtain a copy of the License at
|
|
//
|
|
// http://www.apache.org/licenses/LICENSE-2.0
|
|
//
|
|
// Unless required by applicable law or agreed to in writing, software
|
|
// distributed under the License is distributed on an "AS IS" BASIS,
|
|
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
// See the License for the specific language governing permissions and
|
|
// limitations under the License.
|
|
|
|
#ifndef _ROM_SPI_FLASH_H_
|
|
#define _ROM_SPI_FLASH_H_
|
|
|
|
#include <stdint.h>
|
|
#include <stdbool.h>
|
|
|
|
#include "esp_attr.h"
|
|
|
|
#include "sdkconfig.h"
|
|
|
|
#ifdef CONFIG_LEGACY_INCLUDE_COMMON_HEADERS
|
|
#include "soc/spi_reg.h"
|
|
#endif
|
|
|
|
#ifdef __cplusplus
|
|
extern "C" {
|
|
#endif
|
|
|
|
/** \defgroup spi_flash_apis, spi flash operation related apis
|
|
* @brief spi_flash apis
|
|
*/
|
|
|
|
/** @addtogroup spi_flash_apis
|
|
* @{
|
|
*/
|
|
|
|
/*************************************************************
|
|
* Note
|
|
*************************************************************
|
|
* 1. ESP32 chip have 4 SPI slave/master, however, SPI0 is
|
|
* used as an SPI master to access Flash and ext-SRAM by
|
|
* Cache module. It will support Decryto read for Flash,
|
|
* read/write for ext-SRAM. And SPI1 is also used as an
|
|
* SPI master for Flash read/write and ext-SRAM read/write.
|
|
* It will support Encrypto write for Flash.
|
|
* 2. As an SPI master, SPI support Highest clock to 80M,
|
|
* however, Flash with 80M Clock should be configured
|
|
* for different Flash chips. If you want to use 80M
|
|
* clock We should use the SPI that is certified by
|
|
* Espressif. However, the certification is not started
|
|
* at the time, so please use 40M clock at the moment.
|
|
* 3. SPI Flash can use 2 lines or 4 lines mode. If you
|
|
* use 2 lines mode, you can save two pad SPIHD and
|
|
* SPIWP for gpio. ESP32 support configured SPI pad for
|
|
* Flash, the configuration is stored in efuse and flash.
|
|
* However, the configurations of pads should be certified
|
|
* by Espressif. If you use this function, please use 40M
|
|
* clock at the moment.
|
|
* 4. ESP32 support to use Common SPI command to configure
|
|
* Flash to QIO mode, if you failed to configure with fix
|
|
* command. With Common SPI Command, ESP32 can also provide
|
|
* a way to use same Common SPI command groups on different
|
|
* Flash chips.
|
|
* 5. This functions are not protected by packeting, Please use the
|
|
*************************************************************
|
|
*/
|
|
|
|
#define PERIPHS_SPI_FLASH_CMD SPI_CMD_REG(1)
|
|
#define PERIPHS_SPI_FLASH_ADDR SPI_ADDR_REG(1)
|
|
#define PERIPHS_SPI_FLASH_CTRL SPI_CTRL_REG(1)
|
|
#define PERIPHS_SPI_FLASH_CTRL1 SPI_CTRL1_REG(1)
|
|
#define PERIPHS_SPI_FLASH_STATUS SPI_RD_STATUS_REG(1)
|
|
#define PERIPHS_SPI_FLASH_USRREG SPI_USER_REG(1)
|
|
#define PERIPHS_SPI_FLASH_USRREG1 SPI_USER1_REG(1)
|
|
#define PERIPHS_SPI_FLASH_USRREG2 SPI_USER2_REG(1)
|
|
#define PERIPHS_SPI_FLASH_C0 SPI_W0_REG(1)
|
|
#define PERIPHS_SPI_FLASH_C1 SPI_W1_REG(1)
|
|
#define PERIPHS_SPI_FLASH_C2 SPI_W2_REG(1)
|
|
#define PERIPHS_SPI_FLASH_C3 SPI_W3_REG(1)
|
|
#define PERIPHS_SPI_FLASH_C4 SPI_W4_REG(1)
|
|
#define PERIPHS_SPI_FLASH_C5 SPI_W5_REG(1)
|
|
#define PERIPHS_SPI_FLASH_C6 SPI_W6_REG(1)
|
|
#define PERIPHS_SPI_FLASH_C7 SPI_W7_REG(1)
|
|
#define PERIPHS_SPI_FLASH_TX_CRC SPI_TX_CRC_REG(1)
|
|
|
|
#define SPI0_R_QIO_DUMMY_CYCLELEN 3
|
|
#define SPI0_R_QIO_ADDR_BITSLEN 31
|
|
#define SPI0_R_FAST_DUMMY_CYCLELEN 7
|
|
#define SPI0_R_DIO_DUMMY_CYCLELEN 1
|
|
#define SPI0_R_DIO_ADDR_BITSLEN 27
|
|
#define SPI0_R_FAST_ADDR_BITSLEN 23
|
|
#define SPI0_R_SIO_ADDR_BITSLEN 23
|
|
|
|
#define SPI1_R_QIO_DUMMY_CYCLELEN 3
|
|
#define SPI1_R_QIO_ADDR_BITSLEN 31
|
|
#define SPI1_R_FAST_DUMMY_CYCLELEN 7
|
|
#define SPI1_R_DIO_DUMMY_CYCLELEN 3
|
|
#define SPI1_R_DIO_ADDR_BITSLEN 31
|
|
#define SPI1_R_FAST_ADDR_BITSLEN 23
|
|
#define SPI1_R_SIO_ADDR_BITSLEN 23
|
|
|
|
#define ESP_ROM_SPIFLASH_W_SIO_ADDR_BITSLEN 23
|
|
|
|
#define ESP_ROM_SPIFLASH_TWO_BYTE_STATUS_EN SPI_WRSR_2B
|
|
|
|
//SPI address register
|
|
#define ESP_ROM_SPIFLASH_BYTES_LEN 24
|
|
#define ESP_ROM_SPIFLASH_BUFF_BYTE_WRITE_NUM 32
|
|
#define ESP_ROM_SPIFLASH_BUFF_BYTE_READ_NUM 64
|
|
#define ESP_ROM_SPIFLASH_BUFF_BYTE_READ_BITS 0x3f
|
|
|
|
//SPI status register
|
|
#define ESP_ROM_SPIFLASH_BUSY_FLAG BIT0
|
|
#define ESP_ROM_SPIFLASH_WRENABLE_FLAG BIT1
|
|
#define ESP_ROM_SPIFLASH_BP0 BIT2
|
|
#define ESP_ROM_SPIFLASH_BP1 BIT3
|
|
#define ESP_ROM_SPIFLASH_BP2 BIT4
|
|
#define ESP_ROM_SPIFLASH_WR_PROTECT (ESP_ROM_SPIFLASH_BP0|ESP_ROM_SPIFLASH_BP1|ESP_ROM_SPIFLASH_BP2)
|
|
#define ESP_ROM_SPIFLASH_QE BIT9
|
|
#define ESP_ROM_SPIFLASH_BP_MASK_ISSI (BIT7 | BIT5 | BIT4 | BIT3 | BIT2)
|
|
|
|
//Extra dummy for flash read
|
|
#define ESP_ROM_SPIFLASH_DUMMY_LEN_PLUS_20M 0
|
|
#define ESP_ROM_SPIFLASH_DUMMY_LEN_PLUS_26M 0
|
|
#define ESP_ROM_SPIFLASH_DUMMY_LEN_PLUS_40M 1
|
|
#define ESP_ROM_SPIFLASH_DUMMY_LEN_PLUS_80M 2
|
|
|
|
#define FLASH_ID_GD25LQ32C 0xC86016
|
|
|
|
typedef enum {
|
|
ESP_ROM_SPIFLASH_QIO_MODE = 0,
|
|
ESP_ROM_SPIFLASH_QOUT_MODE,
|
|
ESP_ROM_SPIFLASH_DIO_MODE,
|
|
ESP_ROM_SPIFLASH_DOUT_MODE,
|
|
ESP_ROM_SPIFLASH_FASTRD_MODE,
|
|
ESP_ROM_SPIFLASH_SLOWRD_MODE
|
|
} esp_rom_spiflash_read_mode_t;
|
|
|
|
typedef enum {
|
|
ESP_ROM_SPIFLASH_RESULT_OK,
|
|
ESP_ROM_SPIFLASH_RESULT_ERR,
|
|
ESP_ROM_SPIFLASH_RESULT_TIMEOUT
|
|
} esp_rom_spiflash_result_t;
|
|
|
|
typedef struct {
|
|
uint32_t device_id;
|
|
uint32_t chip_size; // chip size in bytes
|
|
uint32_t block_size;
|
|
uint32_t sector_size;
|
|
uint32_t page_size;
|
|
uint32_t status_mask;
|
|
} esp_rom_spiflash_chip_t;
|
|
|
|
typedef struct {
|
|
uint8_t data_length;
|
|
uint8_t read_cmd0;
|
|
uint8_t read_cmd1;
|
|
uint8_t write_cmd;
|
|
uint16_t data_mask;
|
|
uint16_t data;
|
|
} esp_rom_spiflash_common_cmd_t;
|
|
|
|
/**
|
|
* @brief Fix the bug in SPI hardware communication with Flash/Ext-SRAM in High Speed.
|
|
* Please do not call this function in SDK.
|
|
*
|
|
* @param uint8_t spi: 0 for SPI0(Cache Access), 1 for SPI1(Flash read/write).
|
|
*
|
|
* @param uint8_t freqdiv: Pll is 80M, 4 for 20M, 3 for 26.7M, 2 for 40M, 1 for 80M.
|
|
*
|
|
* @return None
|
|
*/
|
|
void esp_rom_spiflash_fix_dummylen(uint8_t spi, uint8_t freqdiv);
|
|
|
|
/**
|
|
* @brief Select SPI Flash to QIO mode when WP pad is read from Flash.
|
|
* Please do not call this function in SDK.
|
|
*
|
|
* @param uint8_t wp_gpio_num: WP gpio number.
|
|
*
|
|
* @param uint32_t ishspi: 0 for spi, 1 for hspi, flash pad decided by strapping
|
|
* else, bit[5:0] spiclk, bit[11:6] spiq, bit[17:12] spid, bit[23:18] spics0, bit[29:24] spihd
|
|
*
|
|
* @return None
|
|
*/
|
|
void esp_rom_spiflash_select_qiomode(uint8_t wp_gpio_num, uint32_t ishspi);
|
|
|
|
/**
|
|
* @brief Set SPI Flash pad drivers.
|
|
* Please do not call this function in SDK.
|
|
*
|
|
* @param uint8_t wp_gpio_num: WP gpio number.
|
|
*
|
|
* @param uint32_t ishspi: 0 for spi, 1 for hspi, flash pad decided by strapping
|
|
* else, bit[5:0] spiclk, bit[11:6] spiq, bit[17:12] spid, bit[23:18] spics0, bit[29:24] spihd
|
|
*
|
|
* @param uint8_t *drvs: drvs[0]-bit[3:0] for cpiclk, bit[7:4] for spiq, drvs[1]-bit[3:0] for spid, drvs[1]-bit[7:4] for spid
|
|
* drvs[2]-bit[3:0] for spihd, drvs[2]-bit[7:4] for spiwp.
|
|
* Values usually read from falsh by rom code, function usually callde by rom code.
|
|
* if value with bit(3) set, the value is valid, bit[2:0] is the real value.
|
|
*
|
|
* @return None
|
|
*/
|
|
void esp_rom_spiflash_set_drvs(uint8_t wp_gpio_num, uint32_t ishspi, uint8_t *drvs);
|
|
|
|
/**
|
|
* @brief Select SPI Flash function for pads.
|
|
* Please do not call this function in SDK.
|
|
*
|
|
* @param uint32_t ishspi: 0 for spi, 1 for hspi, flash pad decided by strapping
|
|
* else, bit[5:0] spiclk, bit[11:6] spiq, bit[17:12] spid, bit[23:18] spics0, bit[29:24] spihd
|
|
*
|
|
* @return None
|
|
*/
|
|
void esp_rom_spiflash_select_padsfunc(uint32_t ishspi);
|
|
|
|
/**
|
|
* @brief SPI Flash init, clock divisor is 4, use 1 line Slow read mode.
|
|
* Please do not call this function in SDK.
|
|
*
|
|
* @param uint32_t ishspi: 0 for spi, 1 for hspi, flash pad decided by strapping
|
|
* else, bit[5:0] spiclk, bit[11:6] spiq, bit[17:12] spid, bit[23:18] spics0, bit[29:24] spihd
|
|
*
|
|
* @param uint8_t legacy: In legacy mode, more SPI command is used in line.
|
|
*
|
|
* @return None
|
|
*/
|
|
void esp_rom_spiflash_attach(uint32_t ishspi, bool legacy);
|
|
|
|
/**
|
|
* @brief SPI Read Flash status register. We use CMD 0x05 (RDSR).
|
|
* Please do not call this function in SDK.
|
|
*
|
|
* @param esp_rom_spiflash_chip_t *spi : The information for Flash, which is exported from ld file.
|
|
*
|
|
* @param uint32_t *status : The pointer to which to return the Flash status value.
|
|
*
|
|
* @return ESP_ROM_SPIFLASH_RESULT_OK : read OK.
|
|
* ESP_ROM_SPIFLASH_RESULT_ERR : read error.
|
|
* ESP_ROM_SPIFLASH_RESULT_TIMEOUT : read timeout.
|
|
*/
|
|
esp_rom_spiflash_result_t esp_rom_spiflash_read_status(esp_rom_spiflash_chip_t *spi, uint32_t *status);
|
|
|
|
/**
|
|
* @brief SPI Read Flash status register bits 8-15. We use CMD 0x35 (RDSR2).
|
|
* Please do not call this function in SDK.
|
|
*
|
|
* @param esp_rom_spiflash_chip_t *spi : The information for Flash, which is exported from ld file.
|
|
*
|
|
* @param uint32_t *status : The pointer to which to return the Flash status value.
|
|
*
|
|
* @return ESP_ROM_SPIFLASH_RESULT_OK : read OK.
|
|
* ESP_ROM_SPIFLASH_RESULT_ERR : read error.
|
|
* ESP_ROM_SPIFLASH_RESULT_TIMEOUT : read timeout.
|
|
*/
|
|
esp_rom_spiflash_result_t esp_rom_spiflash_read_statushigh(esp_rom_spiflash_chip_t *spi, uint32_t *status);
|
|
|
|
/**
|
|
* @brief Write status to Falsh status register.
|
|
* Please do not call this function in SDK.
|
|
*
|
|
* @param esp_rom_spiflash_chip_t *spi : The information for Flash, which is exported from ld file.
|
|
*
|
|
* @param uint32_t status_value : Value to .
|
|
*
|
|
* @return ESP_ROM_SPIFLASH_RESULT_OK : write OK.
|
|
* ESP_ROM_SPIFLASH_RESULT_ERR : write error.
|
|
* ESP_ROM_SPIFLASH_RESULT_TIMEOUT : write timeout.
|
|
*/
|
|
esp_rom_spiflash_result_t esp_rom_spiflash_write_status(esp_rom_spiflash_chip_t *spi, uint32_t status_value);
|
|
|
|
/**
|
|
* @brief Use a command to Read Flash status register.
|
|
* Please do not call this function in SDK.
|
|
*
|
|
* @param esp_rom_spiflash_chip_t *spi : The information for Flash, which is exported from ld file.
|
|
*
|
|
* @param uint32_t*status : The pointer to which to return the Flash status value.
|
|
*
|
|
* @return ESP_ROM_SPIFLASH_RESULT_OK : read OK.
|
|
* ESP_ROM_SPIFLASH_RESULT_ERR : read error.
|
|
* ESP_ROM_SPIFLASH_RESULT_TIMEOUT : read timeout.
|
|
*/
|
|
esp_rom_spiflash_result_t esp_rom_spiflash_read_user_cmd(uint32_t *status, uint8_t cmd);
|
|
|
|
/**
|
|
* @brief Config SPI Flash read mode when init.
|
|
* Please do not call this function in SDK.
|
|
*
|
|
* @param esp_rom_spiflash_read_mode_t mode : QIO/QOUT/DIO/DOUT/FastRD/SlowRD.
|
|
*
|
|
* This function does not try to set the QIO Enable bit in the status register, caller is responsible for this.
|
|
*
|
|
* @return ESP_ROM_SPIFLASH_RESULT_OK : config OK.
|
|
* ESP_ROM_SPIFLASH_RESULT_ERR : config error.
|
|
* ESP_ROM_SPIFLASH_RESULT_TIMEOUT : config timeout.
|
|
*/
|
|
esp_rom_spiflash_result_t esp_rom_spiflash_config_readmode(esp_rom_spiflash_read_mode_t mode);
|
|
|
|
/**
|
|
* @brief Config SPI Flash clock divisor.
|
|
* Please do not call this function in SDK.
|
|
*
|
|
* @param uint8_t freqdiv: clock divisor.
|
|
*
|
|
* @param uint8_t spi: 0 for SPI0, 1 for SPI1.
|
|
*
|
|
* @return ESP_ROM_SPIFLASH_RESULT_OK : config OK.
|
|
* ESP_ROM_SPIFLASH_RESULT_ERR : config error.
|
|
* ESP_ROM_SPIFLASH_RESULT_TIMEOUT : config timeout.
|
|
*/
|
|
esp_rom_spiflash_result_t esp_rom_spiflash_config_clk(uint8_t freqdiv, uint8_t spi);
|
|
|
|
/**
|
|
* @brief Send CommonCmd to Flash so that is can go into QIO mode, some Flash use different CMD.
|
|
* Please do not call this function in SDK.
|
|
*
|
|
* @param esp_rom_spiflash_common_cmd_t *cmd : A struct to show the action of a command.
|
|
*
|
|
* @return uint16_t 0 : do not send command any more.
|
|
* 1 : go to the next command.
|
|
* n > 1 : skip (n - 1) commands.
|
|
*/
|
|
uint16_t esp_rom_spiflash_common_cmd(esp_rom_spiflash_common_cmd_t *cmd);
|
|
|
|
/**
|
|
* @brief Unlock SPI write protect.
|
|
* Please do not call this function in SDK.
|
|
*
|
|
* @param None.
|
|
*
|
|
* @return ESP_ROM_SPIFLASH_RESULT_OK : Unlock OK.
|
|
* ESP_ROM_SPIFLASH_RESULT_ERR : Unlock error.
|
|
* ESP_ROM_SPIFLASH_RESULT_TIMEOUT : Unlock timeout.
|
|
*/
|
|
esp_rom_spiflash_result_t esp_rom_spiflash_unlock(void);
|
|
|
|
/**
|
|
* @brief SPI write protect.
|
|
* Please do not call this function in SDK.
|
|
*
|
|
* @param None.
|
|
*
|
|
* @return ESP_ROM_SPIFLASH_RESULT_OK : Lock OK.
|
|
* ESP_ROM_SPIFLASH_RESULT_ERR : Lock error.
|
|
* ESP_ROM_SPIFLASH_RESULT_TIMEOUT : Lock timeout.
|
|
*/
|
|
esp_rom_spiflash_result_t esp_rom_spiflash_lock(void);
|
|
|
|
/**
|
|
* @brief Update SPI Flash parameter.
|
|
* Please do not call this function in SDK.
|
|
*
|
|
* @param uint32_t deviceId : Device ID read from SPI, the low 32 bit.
|
|
*
|
|
* @param uint32_t chip_size : The Flash size.
|
|
*
|
|
* @param uint32_t block_size : The Flash block size.
|
|
*
|
|
* @param uint32_t sector_size : The Flash sector size.
|
|
*
|
|
* @param uint32_t page_size : The Flash page size.
|
|
*
|
|
* @param uint32_t status_mask : The Mask used when read status from Flash(use single CMD).
|
|
*
|
|
* @return ESP_ROM_SPIFLASH_RESULT_OK : Update OK.
|
|
* ESP_ROM_SPIFLASH_RESULT_ERR : Update error.
|
|
* ESP_ROM_SPIFLASH_RESULT_TIMEOUT : Update timeout.
|
|
*/
|
|
esp_rom_spiflash_result_t esp_rom_spiflash_config_param(uint32_t deviceId, uint32_t chip_size, uint32_t block_size,
|
|
uint32_t sector_size, uint32_t page_size, uint32_t status_mask);
|
|
|
|
/**
|
|
* @brief Erase whole flash chip.
|
|
* Please do not call this function in SDK.
|
|
*
|
|
* @param None
|
|
*
|
|
* @return ESP_ROM_SPIFLASH_RESULT_OK : Erase OK.
|
|
* ESP_ROM_SPIFLASH_RESULT_ERR : Erase error.
|
|
* ESP_ROM_SPIFLASH_RESULT_TIMEOUT : Erase timeout.
|
|
*/
|
|
esp_rom_spiflash_result_t esp_rom_spiflash_erase_chip(void);
|
|
|
|
/**
|
|
* @brief Erase a 64KB block of flash
|
|
* Uses SPI flash command D8H.
|
|
* Please do not call this function in SDK.
|
|
*
|
|
* @param uint32_t block_num : Which block to erase.
|
|
*
|
|
* @return ESP_ROM_SPIFLASH_RESULT_OK : Erase OK.
|
|
* ESP_ROM_SPIFLASH_RESULT_ERR : Erase error.
|
|
* ESP_ROM_SPIFLASH_RESULT_TIMEOUT : Erase timeout.
|
|
*/
|
|
esp_rom_spiflash_result_t esp_rom_spiflash_erase_block(uint32_t block_num);
|
|
|
|
/**
|
|
* @brief Erase a sector of flash.
|
|
* Uses SPI flash command 20H.
|
|
* Please do not call this function in SDK.
|
|
*
|
|
* @param uint32_t sector_num : Which sector to erase.
|
|
*
|
|
* @return ESP_ROM_SPIFLASH_RESULT_OK : Erase OK.
|
|
* ESP_ROM_SPIFLASH_RESULT_ERR : Erase error.
|
|
* ESP_ROM_SPIFLASH_RESULT_TIMEOUT : Erase timeout.
|
|
*/
|
|
esp_rom_spiflash_result_t esp_rom_spiflash_erase_sector(uint32_t sector_num);
|
|
|
|
/**
|
|
* @brief Erase some sectors.
|
|
* Please do not call this function in SDK.
|
|
*
|
|
* @param uint32_t start_addr : Start addr to erase, should be sector aligned.
|
|
*
|
|
* @param uint32_t area_len : Length to erase, should be sector aligned.
|
|
*
|
|
* @return ESP_ROM_SPIFLASH_RESULT_OK : Erase OK.
|
|
* ESP_ROM_SPIFLASH_RESULT_ERR : Erase error.
|
|
* ESP_ROM_SPIFLASH_RESULT_TIMEOUT : Erase timeout.
|
|
*/
|
|
esp_rom_spiflash_result_t esp_rom_spiflash_erase_area(uint32_t start_addr, uint32_t area_len);
|
|
|
|
/**
|
|
* @brief Write Data to Flash, you should Erase it yourself if need.
|
|
* Please do not call this function in SDK.
|
|
*
|
|
* @param uint32_t dest_addr : Address to write, should be 4 bytes aligned.
|
|
*
|
|
* @param const uint32_t *src : The pointer to data which is to write.
|
|
*
|
|
* @param uint32_t len : Length to write, should be 4 bytes aligned.
|
|
*
|
|
* @return ESP_ROM_SPIFLASH_RESULT_OK : Write OK.
|
|
* ESP_ROM_SPIFLASH_RESULT_ERR : Write error.
|
|
* ESP_ROM_SPIFLASH_RESULT_TIMEOUT : Write timeout.
|
|
*/
|
|
esp_rom_spiflash_result_t esp_rom_spiflash_write(uint32_t dest_addr, const uint32_t *src, int32_t len);
|
|
|
|
/**
|
|
* @brief Read Data from Flash, you should Erase it yourself if need.
|
|
* Please do not call this function in SDK.
|
|
*
|
|
* @param uint32_t src_addr : Address to read, should be 4 bytes aligned.
|
|
*
|
|
* @param uint32_t *dest : The buf to read the data.
|
|
*
|
|
* @param uint32_t len : Length to read, should be 4 bytes aligned.
|
|
*
|
|
* @return ESP_ROM_SPIFLASH_RESULT_OK : Read OK.
|
|
* ESP_ROM_SPIFLASH_RESULT_ERR : Read error.
|
|
* ESP_ROM_SPIFLASH_RESULT_TIMEOUT : Read timeout.
|
|
*/
|
|
esp_rom_spiflash_result_t esp_rom_spiflash_read(uint32_t src_addr, uint32_t *dest, int32_t len);
|
|
|
|
/**
|
|
* @brief SPI1 go into encrypto mode.
|
|
* Please do not call this function in SDK.
|
|
*
|
|
* @param None
|
|
*
|
|
* @return None
|
|
*/
|
|
void esp_rom_spiflash_write_encrypted_enable(void);
|
|
|
|
/**
|
|
* @brief Prepare 32 Bytes data to encrpto writing, you should Erase it yourself if need.
|
|
* Please do not call this function in SDK.
|
|
*
|
|
* @param uint32_t flash_addr : Address to write, should be 32 bytes aligned.
|
|
*
|
|
* @param uint32_t *data : The pointer to data which is to write.
|
|
*
|
|
* @return ESP_ROM_SPIFLASH_RESULT_OK : Prepare OK.
|
|
* ESP_ROM_SPIFLASH_RESULT_ERR : Prepare error.
|
|
* ESP_ROM_SPIFLASH_RESULT_TIMEOUT : Prepare timeout.
|
|
*/
|
|
esp_rom_spiflash_result_t esp_rom_spiflash_prepare_encrypted_data(uint32_t flash_addr, uint32_t *data);
|
|
|
|
/**
|
|
* @brief SPI1 go out of encrypto mode.
|
|
* Please do not call this function in SDK.
|
|
*
|
|
* @param None
|
|
*
|
|
* @return None
|
|
*/
|
|
void esp_rom_spiflash_write_encrypted_disable(void);
|
|
|
|
/**
|
|
* @brief Write data to flash with transparent encryption.
|
|
* @note Sectors to be written should already be erased.
|
|
*
|
|
* @note Please do not call this function in SDK.
|
|
*
|
|
* @param uint32_t flash_addr : Address to write, should be 32 byte aligned.
|
|
*
|
|
* @param uint32_t *data : The pointer to data to write. Note, this pointer must
|
|
* be 32 bit aligned and the content of the data will be
|
|
* modified by the encryption function.
|
|
*
|
|
* @param uint32_t len : Length to write, should be 32 bytes aligned.
|
|
*
|
|
* @return ESP_ROM_SPIFLASH_RESULT_OK : Data written successfully.
|
|
* ESP_ROM_SPIFLASH_RESULT_ERR : Encryption write error.
|
|
* ESP_ROM_SPIFLASH_RESULT_TIMEOUT : Encrypto write timeout.
|
|
*/
|
|
esp_rom_spiflash_result_t esp_rom_spiflash_write_encrypted(uint32_t flash_addr, uint32_t *data, uint32_t len);
|
|
|
|
|
|
/** @brief Wait until SPI flash write operation is complete
|
|
*
|
|
* @note Please do not call this function in SDK.
|
|
*
|
|
* Reads the Write In Progress bit of the SPI flash status register,
|
|
* repeats until this bit is zero (indicating write complete).
|
|
*
|
|
* @return ESP_ROM_SPIFLASH_RESULT_OK : Write is complete
|
|
* ESP_ROM_SPIFLASH_RESULT_ERR : Error while reading status.
|
|
*/
|
|
esp_rom_spiflash_result_t esp_rom_spiflash_wait_idle(esp_rom_spiflash_chip_t *spi);
|
|
|
|
|
|
/** @brief Enable Quad I/O pin functions
|
|
*
|
|
* @note Please do not call this function in SDK.
|
|
*
|
|
* Sets the HD & WP pin functions for Quad I/O modes, based on the
|
|
* efuse SPI pin configuration.
|
|
*
|
|
* @param wp_gpio_num - Number of the WP pin to reconfigure for quad I/O.
|
|
*
|
|
* @param spiconfig - Pin configuration, as returned from ets_efuse_get_spiconfig().
|
|
* - If this parameter is 0, default SPI pins are used and wp_gpio_num parameter is ignored.
|
|
* - If this parameter is 1, default HSPI pins are used and wp_gpio_num parameter is ignored.
|
|
* - For other values, this parameter encodes the HD pin number and also the CLK pin number. CLK pin selection is used
|
|
* to determine if HSPI or SPI peripheral will be used (use HSPI if CLK pin is the HSPI clock pin, otherwise use SPI).
|
|
* Both HD & WP pins are configured via GPIO matrix to map to the selected peripheral.
|
|
*/
|
|
void esp_rom_spiflash_select_qio_pins(uint8_t wp_gpio_num, uint32_t spiconfig);
|
|
|
|
/**
|
|
* @brief Clear WEL bit unconditionally.
|
|
*
|
|
* @return always ESP_ROM_SPIFLASH_RESULT_OK
|
|
*/
|
|
esp_rom_spiflash_result_t esp_rom_spiflash_write_disable(void);
|
|
|
|
/** @brief Global esp_rom_spiflash_chip_t structure used by ROM functions
|
|
*
|
|
*/
|
|
extern esp_rom_spiflash_chip_t g_rom_flashchip;
|
|
|
|
extern uint8_t g_rom_spiflash_dummy_len_plus[];
|
|
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
#ifdef __cplusplus
|
|
}
|
|
#endif
|
|
|
|
#endif /* _ROM_SPI_FLASH_H_ */
|