esp-idf/components/esp_rom/include/esp32c3/rom/efuse.h

393 wiersze
12 KiB
C

// Copyright 2020 Espressif Systems (Shanghai) PTE LTD
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
//
// http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
#ifndef _ROM_EFUSE_H_
#define _ROM_EFUSE_H_
#ifdef __cplusplus
extern "C" {
#endif
#include <stdint.h>
#include <stddef.h>
#include <stdbool.h>
/** \defgroup efuse_APIs efuse APIs
* @brief ESP32 efuse read/write APIs
* @attention
*
*/
/** @addtogroup efuse_APIs
* @{
*/
typedef enum {
ETS_EFUSE_KEY_PURPOSE_USER = 0,
ETS_EFUSE_KEY_PURPOSE_RESERVED = 1,
ETS_EFUSE_KEY_PURPOSE_XTS_AES_128_KEY = 4,
ETS_EFUSE_KEY_PURPOSE_HMAC_DOWN_ALL = 5,
ETS_EFUSE_KEY_PURPOSE_HMAC_DOWN_JTAG = 6,
ETS_EFUSE_KEY_PURPOSE_HMAC_DOWN_DIGITAL_SIGNATURE = 7,
ETS_EFUSE_KEY_PURPOSE_HMAC_UP = 8,
ETS_EFUSE_KEY_PURPOSE_SECURE_BOOT_DIGEST0 = 9,
ETS_EFUSE_KEY_PURPOSE_SECURE_BOOT_DIGEST1 = 10,
ETS_EFUSE_KEY_PURPOSE_SECURE_BOOT_DIGEST2 = 11,
ETS_EFUSE_KEY_PURPOSE_MAX,
} ets_efuse_purpose_t;
typedef enum {
ETS_EFUSE_BLOCK0 = 0,
ETS_EFUSE_MAC_SPI_SYS_0 = 1,
ETS_EFUSE_BLOCK_SYS_DATA = 2,
ETS_EFUSE_BLOCK_USR_DATA = 3,
ETS_EFUSE_BLOCK_KEY0 = 4,
ETS_EFUSE_BLOCK_KEY1 = 5,
ETS_EFUSE_BLOCK_KEY2 = 6,
ETS_EFUSE_BLOCK_KEY3 = 7,
ETS_EFUSE_BLOCK_KEY4 = 8,
ETS_EFUSE_BLOCK_KEY5 = 9,
ETS_EFUSE_BLOCK_KEY6 = 10,
ETS_EFUSE_BLOCK_MAX,
} ets_efuse_block_t;
/**
* @brief set timing accroding the apb clock, so no read error or write error happens.
*
* @param clock: apb clock in HZ, only accept 5M(in FPGA), 10M(in FPGA), 20M, 40M, 80M.
*
* @return : 0 if success, others if clock not accepted
*/
int ets_efuse_set_timing(uint32_t clock);
/**
* @brief Enable efuse subsystem. Called after reset. Doesn't need to be called again.
*/
void ets_efuse_start(void);
/**
* @brief Efuse read operation: copies data from physical efuses to efuse read registers.
*
* @param null
*
* @return : 0 if success, others if apb clock is not accepted
*/
int ets_efuse_read(void);
/**
* @brief Efuse write operation: Copies data from efuse write registers to efuse. Operates on a single block of efuses at a time.
*
* @note This function does not update read efuses, call ets_efuse_read() once all programming is complete.
*
* @return : 0 if success, others if apb clock is not accepted
*/
int ets_efuse_program(ets_efuse_block_t block);
/**
* @brief Set all Efuse program registers to zero.
*
* Call this before writing new data to the program registers.
*/
void ets_efuse_clear_program_registers(void);
/**
* @brief Program a block of key data to an efuse block
*
* @param key_block Block to read purpose for. Must be in range ETS_EFUSE_BLOCK_KEY0 to ETS_EFUSE_BLOCK_KEY6. Key block must be unused (@ref ets_efuse_key_block_unused).
* @param purpose Purpose to set for this key. Purpose must be already unset.
* @param data Pointer to data to write.
* @param data_len Length of data to write.
*
* @note This function also calls ets_efuse_program() for the specified block, and for block 0 (setting the purpose)
*/
int ets_efuse_write_key(ets_efuse_block_t key_block, ets_efuse_purpose_t purpose, const void *data, size_t data_len);
/* @brief Return the address of a particular efuse block's first read register
*
* @param block Index of efuse block to look up
*
* @return 0 if block is invalid, otherwise a numeric read register address
* of the first word in the block.
*/
uint32_t ets_efuse_get_read_register_address(ets_efuse_block_t block);
/**
* @brief Return the current purpose set for an efuse key block
*
* @param key_block Block to read purpose for. Must be in range ETS_EFUSE_BLOCK_KEY0 to ETS_EFUSE_BLOCK_KEY6.
*/
ets_efuse_purpose_t ets_efuse_get_key_purpose(ets_efuse_block_t key_block);
/**
* @brief Find a key block with the particular purpose set
*
* @param purpose Purpose to search for.
* @param[out] key_block Pointer which will be set to the key block if found. Can be NULL, if only need to test the key block exists.
* @return true if found, false if not found. If false, value at key_block pointer is unchanged.
*/
bool ets_efuse_find_purpose(ets_efuse_purpose_t purpose, ets_efuse_block_t *key_block);
/**
* Return true if the key block is unused, false otherwise.
*
* An unused key block is all zero content, not read or write protected,
* and has purpose 0 (ETS_EFUSE_KEY_PURPOSE_USER)
*
* @param key_block key block to check.
*
* @return true if key block is unused, false if key block or used
* or the specified block index is not a key block.
*/
bool ets_efuse_key_block_unused(ets_efuse_block_t key_block);
/**
* @brief Search for an unused key block and return the first one found.
*
* See @ref ets_efuse_key_block_unused for a description of an unused key block.
*
* @return First unused key block, or ETS_EFUSE_BLOCK_MAX if no unused key block is found.
*/
ets_efuse_block_t ets_efuse_find_unused_key_block(void);
/**
* @brief Return the number of unused efuse key blocks (0-6)
*/
unsigned ets_efuse_count_unused_key_blocks(void);
/**
* @brief Calculate Reed-Solomon Encoding values for a block of efuse data.
*
* @param data Pointer to data buffer (length 32 bytes)
* @param rs_values Pointer to write encoded data to (length 12 bytes)
*/
void ets_efuse_rs_calculate(const void *data, void *rs_values);
/**
* @brief Read spi flash pads configuration from Efuse
*
* @return
* - 0 for default SPI pins.
* - 1 for default HSPI pins.
* - Other values define a custom pin configuration mask. Pins are encoded as per the EFUSE_SPICONFIG_RET_SPICLK,
* EFUSE_SPICONFIG_RET_SPIQ, EFUSE_SPICONFIG_RET_SPID, EFUSE_SPICONFIG_RET_SPICS0, EFUSE_SPICONFIG_RET_SPIHD macros.
* WP pin (for quad I/O modes) is not saved in efuse and not returned by this function.
*/
uint32_t ets_efuse_get_spiconfig(void);
/**
* @brief Read spi flash wp pad from Efuse
*
* @return
* - 0x3f for invalid.
* - 0~46 is valid.
*/
uint32_t ets_efuse_get_wp_pad(void);
/**
* @brief Read opi flash pads configuration from Efuse
*
* @return
* - 0 for default SPI pins.
* - Other values define a custom pin configuration mask. From the LSB, every 6 bits represent a GPIO number which stand for:
* DQS, D4, D5, D6, D7 accordingly.
*/
uint32_t ets_efuse_get_opiconfig(void);
/**
* @brief Read if download mode disabled from Efuse
*
* @return
* - true for efuse disable download mode.
* - false for efuse doesn't disable download mode.
*/
bool ets_efuse_download_modes_disabled(void);
/**
* @brief Read if legacy spi flash boot mode disabled from Efuse
*
* @return
* - true for efuse disable legacy spi flash boot mode.
* - false for efuse doesn't disable legacy spi flash boot mode.
*/
bool ets_efuse_legacy_spi_boot_mode_disabled(void);
/**
* @brief Read if uart print control value from Efuse
*
* @return
* - 0 for uart force print.
* - 1 for uart print when GPIO8 is low when digital reset.
* 2 for uart print when GPIO8 is high when digital reset.
* 3 for uart force slient
*/
uint32_t ets_efuse_get_uart_print_control(void);
/**
* @brief Read which channel will used by ROM to print
*
* @return
* - 0 for UART0.
* - 1 for UART1.
*/
uint32_t ets_efuse_get_uart_print_channel(void);
/**
* @brief Read if usb download mode disabled from Efuse
*
* (Also returns true if security download mode is enabled, as this mode
* disables USB download.)
*
* @return
* - true for efuse disable usb download mode.
* - false for efuse doesn't disable usb download mode.
*/
bool ets_efuse_usb_download_mode_disabled(void);
/**
* @brief Read if tiny basic mode disabled from Efuse
*
* @return
* - true for efuse disable tiny basic mode.
* - false for efuse doesn't disable tiny basic mode.
*/
bool ets_efuse_tiny_basic_mode_disabled(void);
/**
* @brief Read if usb module disabled from Efuse
*
* @return
* - true for efuse disable usb module.
* - false for efuse doesn't disable usb module.
*/
bool ets_efuse_usb_module_disabled(void);
/**
* @brief Read if security download modes enabled from Efuse
*
* @return
* - true for efuse enable security download mode.
* - false for efuse doesn't enable security download mode.
*/
bool ets_efuse_security_download_modes_enabled(void);
/**
* @brief Return true if secure boot is enabled in EFuse
*/
bool ets_efuse_secure_boot_enabled(void);
/**
* @brief Return true if secure boot aggressive revoke is enabled in EFuse
*/
bool ets_efuse_secure_boot_aggressive_revoke_enabled(void);
/**
* @brief Return true if cache encryption (flash, etc) is enabled from boot via EFuse
*/
bool ets_efuse_cache_encryption_enabled(void);
/**
* @brief Return true if EFuse indicates an external phy needs to be used for USB
*/
bool ets_efuse_usb_use_ext_phy(void);
/**
* @brief Return true if EFuse indicates USB device persistence is disabled
*/
bool ets_efuse_usb_force_nopersist(void);
/**
* @brief Return true if OPI pins GPIO33-37 are powered by VDDSPI, otherwise by VDD33CPU
*/
bool ets_efuse_flash_opi_5pads_power_sel_vddspi(void);
/**
* @brief Return true if EFuse indicates an opi flash is attached.
*/
bool ets_efuse_flash_opi_mode(void);
/**
* @brief Return true if EFuse indicates to send a flash resume command.
*/
bool ets_efuse_force_send_resume(void);
/**
* @brief return the time in us ROM boot need wait flash to power on from Efuse
*
* @return
* - uint32_t the time in us.
*/
uint32_t ets_efuse_get_flash_delay_us(void);
#define EFUSE_SPICONFIG_SPI_DEFAULTS 0
#define EFUSE_SPICONFIG_HSPI_DEFAULTS 1
#define EFUSE_SPICONFIG_RET_SPICLK_MASK 0x3f
#define EFUSE_SPICONFIG_RET_SPICLK_SHIFT 0
#define EFUSE_SPICONFIG_RET_SPICLK(ret) (((ret) >> EFUSE_SPICONFIG_RET_SPICLK_SHIFT) & EFUSE_SPICONFIG_RET_SPICLK_MASK)
#define EFUSE_SPICONFIG_RET_SPIQ_MASK 0x3f
#define EFUSE_SPICONFIG_RET_SPIQ_SHIFT 6
#define EFUSE_SPICONFIG_RET_SPIQ(ret) (((ret) >> EFUSE_SPICONFIG_RET_SPIQ_SHIFT) & EFUSE_SPICONFIG_RET_SPIQ_MASK)
#define EFUSE_SPICONFIG_RET_SPID_MASK 0x3f
#define EFUSE_SPICONFIG_RET_SPID_SHIFT 12
#define EFUSE_SPICONFIG_RET_SPID(ret) (((ret) >> EFUSE_SPICONFIG_RET_SPID_SHIFT) & EFUSE_SPICONFIG_RET_SPID_MASK)
#define EFUSE_SPICONFIG_RET_SPICS0_MASK 0x3f
#define EFUSE_SPICONFIG_RET_SPICS0_SHIFT 18
#define EFUSE_SPICONFIG_RET_SPICS0(ret) (((ret) >> EFUSE_SPICONFIG_RET_SPICS0_SHIFT) & EFUSE_SPICONFIG_RET_SPICS0_MASK)
#define EFUSE_SPICONFIG_RET_SPIHD_MASK 0x3f
#define EFUSE_SPICONFIG_RET_SPIHD_SHIFT 24
#define EFUSE_SPICONFIG_RET_SPIHD(ret) (((ret) >> EFUSE_SPICONFIG_RET_SPIHD_SHIFT) & EFUSE_SPICONFIG_RET_SPIHD_MASK)
/**
* @brief Enable JTAG temporarily by writing a JTAG HMAC "key" into
* the JTAG_CTRL registers.
*
* Works if JTAG has been "soft" disabled by burning the EFUSE_SOFT_DIS_JTAG efuse.
*
* Will enable the HMAC module to generate a "downstream" HMAC value from a key already saved in efuse, and then write the JTAG HMAC "key" which will enable JTAG if the two keys match.
*
* @param jtag_hmac_key Pointer to a 32 byte array containing a valid key. Supplied by user.
* @param key_block Index of a key block containing the source for this key.
*
* @return ETS_FAILED if HMAC operation fails or invalid parameter, ETS_OK otherwise. ETS_OK doesn't necessarily mean that JTAG was enabled.
*/
int ets_jtag_enable_temporarily(const uint8_t *jtag_hmac_key, ets_efuse_block_t key_block);
/**
* @brief A crc8 algorithm used for MAC addresses in efuse
*
* @param unsigned char const *p : Pointer to original data.
*
* @param unsigned int len : Data length in byte.
*
* @return unsigned char: Crc value.
*/
unsigned char esp_crc8(unsigned char const *p, unsigned int len);
/**
* @}
*/
#ifdef __cplusplus
}
#endif
#endif /* _ROM_EFUSE_H_ */